FSW-2104W 4-Port Media Streaming Plus 1 Fiber Port Switch
LEGAL The information in this publication has been carefully checked and is believed to be entirely accurate at the time of publication. CTC Union Technologies assumes no responsibility, however, for possible errors or omissions, or for any consequences resulting from the use of the information contained herein.
CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60, Zhouzi St. Neihu, Taipei, 114 Taiwan Phone: +886-2-2659-1021 FAX: +886-2-2799-1355 FSW-2104W 4-port 10/100M + 1-port 100Base-FX WAN Web Smart Media Streaming Fiber Switch * IGMP Snooping v1 / v2 * IGMP Proxy v1 / v2 * Web-Based Management * Built-in wire speed NAT * QoS Functions * DHCP solutions *SNMP v1 / v2 User Manual Version 1.
Contents Chapter 1: About This Guide ................................................................................................. 7 Chapter 2: Introduction .............................................................................................................. 7 2.1 Product Description...................................................................................................... 7 2.2 Product Features..........................................................................................
FSW-2104W Multimedia Residential Gateway Chapter 1: About This Guide Thank you for choosing the FSW-2104W FTTx Router. This router provides dedicate solutions for Fiber to the Home networks for Triple-Play service. To connecting your local network can share Internet access, files and fun for multiple PCs through one ISP account. It is an easy, web-based setup for installation and management. This guide will configure the router easy.
FSW-2104W Multimedia Residential Gateway 2.3 Product Specifications IEEE802.3 10Base-T, IEEE802.
FSW-2104W Multimedia Residential Gateway Chapter 3: Connecting to Router 3.1 System Requirements • • • • Broadband Internet Access Service (FTTx) One single mode fiber connection using dual fiber or single fiber (WDM) Each PC on the LAN needs a working Ethernet Adapter and an Ethernet cable with RJ45 connectors TCP/IP protocol must be installed on each PC 3.2 Installation Environment Requirements • • • • • Not in direct sunlight or near a heater or heating vent Not cluttered or crowded.
FSW-2104W Multimedia Residential Gateway Figure 4-1 Successful result of Ping command If the result displayed is same as to what is shown in figure 4-1, the connection between your PC and the router has been established. Figure 4-2 Fail result of ping command If the result displayed is similar to what shown in figure 4-2, it means that your PC has not connected to the router. If so, refer to the following steps for a solution. 1.
FSW-2104W Multimedia Residential Gateway Chapter 5: Configuring the Router 5.1 login Enter the User name and password correctly and click OK button (shown in figure 5-1). After your successful login, you can configure and manage the router. There are fourteen main menus are: Status, LAN, WAN, NAT, Firewall, Qos, IGMP, SNMP, SNTP, VLAN config, Port config, Storm Control, Tool, System Logs. On the right of the web-based utility, there are the detailed explanations and instructions for the corresponding page.
FSW-2104W Multimedia Residential Gateway 5.2.1.2 LAN Status This field displays the current settings or information for the LAN, including the MAC address, IP address and Subnet Mask. Figure 5-2 Router Status 5.3 LAN Figure 5-3 the LAN menu There are two submenus under the LAN menu (shown in figure 5-3): LAN, DHCP Clients. Click any of them, and you will be able to configure the corresponding function.
FSW-2104W Multimedia Residential Gateway 5.3.1 LAN Please configure the IP parameters of the LAN on this page. Figure 5-4 LAN Setup and DHCP Setup • • • • • • • • IP Address - Enter the IP address of your router in dotted-decimal notation (factory default: 192.168.123.252). Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask. MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed.
FSW-2104W Multimedia Residential Gateway 5.3.2 DHCP Clients This page shows Host IP Address, Host IP Address for each DHCP Client attached to the router (figure 5-5): Figure 5-5 DHCP Clients • • • NO. - The index of the DHCP Client Host IP Address - The name of the DHCP client Host MAC Address - The MAC address of the DHCP client You cannot change any of the values on this page. To update this page and to show the current attached devices, click on the Refresh button. 5.
FSW-2104W Multimedia Residential Gateway 5.4.1 WAN Connection You can configure the WAN port parameters on this page. First, please choose the WAN Connection Type (Dynamic IP/Static IP / PPPoE ) to the Internet. The default type is PPPoE. If you aren’t given any login parameters (fixed IP address, logging ID, etc), please select Dynamic IP. If you are given a fixed IP (static IP), please select Static IP. If you are given a user name and a password, please select PPPoE.
FSW-2104W Multimedia Residential Gateway 2. If you choose Static IP, you should have fixed IP parameters specified by your ISP. The Static IP settings page will appear, shown in figure 5-8: Figure 5-8 WAN - Static IP Please type the following parameters into the spaces provided: • • • • • IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0.
FSW-2104W Multimedia Residential Gateway 3. If you choose PPPoE, you should enter the following parameters (figure 5-9): Figure 5-9 WAN – PPPoE • • • User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Auto Connect - Connect automatically after the router is disconnected. To use this option, click the radio button. Manual Connect - You can configure the router to make it connect or disconnect manually.
FSW-2104W Multimedia Residential Gateway 5.5 NAT Figure 5-11 The NAT menus There is one submenu under the NAT menu (shown in figure 5-11): Virtual Server. Click it, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below : 5.5.1 Virtual Server Virtual server can be used for setting up public services on your LAN, such as DNS, Email and FTP.
FSW-2104W Multimedia Residential Gateway 5.6 Firewall Figure 5-13 Firewalls There are two submenus under the Firewall menu (shown in figure 5-13): WAN IP Filter and LAN MAC Filter. 5.6.1 WAN IP Filter Using The Wan IP Filtering feature allows you to control Internet Access by WAN IP addresses. The IP Address Filtering is set on this page,( shown in figure 5-14) : Figure 5-14 Wan IP Filter 5.6.
FSW-2104W Multimedia Residential Gateway 5.7 QoS Figure 5-16 QoS There are two submenus under the Tools menu (shown in figure 5-16): Qos Priority, Qos(DSCP) Configuration. Click any of them, and you will be able to configure the corresponding function. 5.7.1 QoS Priority Configuration Figure 5-17 QoS Priority Configuration • QOS Mode：there are 2 options: Disable, ToS/Dscp Priority. Select ToS/Dscp Priority, It make TOS/DSCP priority function in use. 5.7.
FSW-2104W Multimedia Residential Gateway 5.8 IGMP Figure 5-19 IGMP Multicast forwarding enables transmitting packets from either a specific multicast group to a source or from a nonspecific source to a multicast group. There are two submenus under the Tools menu (shown in figure 5-19): IGMP Configuration, IGMP Status. Click any of them, and you will be able to configure the corresponding function. 5.8.1 IGMP Configuration You can set up which port the IGMP packets send to on this page.
FSW-2104W Multimedia Residential Gateway 5.8.2 IGMP Status You can see the IGMP status on this page, shown in figure 5-21: Figure 5-21 IGMP Status • • • NO.：The number of the IGMP entries. IP Multicast Group ID：The ID of IP Multicast Group. Each IP Multicast Group have only one ID. Port Map: The port which receive the IGMP packets from IGMP router port you set. 5.9 SNMP There are two submenus under the Tools menu (shown in figure 5-22): Figure 5-22 SNMP Global Configuration, Trap Configuration.
FSW-2104W Multimedia Residential Gateway • • • • • • SNMP Mode.：Enable or Disable the SNMP mode SNMP Community：the SNMP Community, include public or private. SNMP SERVER: the IP of SNMP SERVER. SNMP SERVER Port: the port of SNMP SERVER. SNMP Available IP: the Available IP of SNMP. SNMP Available Mask: the Available Mask of SNMP 5.9.2 Trap Configuration Figure 5-24 Trap Configuration • • Trap Target Address：the IP of target trap Trap Target Port：the port of target trap. 5.
FSW-2104W Multimedia Residential Gateway 5.11 VLAN Configuration There is only one submenu under the Tools menu (shown in figure 5-27): Tag VLAN Configuration. Click it, and you will be able to configure the corresponding function. Figure 5-27VLAN configuration 5.11.1 Tag VLAN Configuration Figure 5-28 802.1Q VLAN • • • • • VLAN Index：the index of VLAN VLAN ID：the ID of VLAN Status: the Status of VLAN Port ID: the ID of port. Rule: the rule which the stream can through 5.
FSW-2104W Multimedia Residential Gateway 5.12.1 Port Para Figure 5-30 Port Para Configuration • • • • Port : There are five ports you can select to modify(WAN, LAN-1, LAN-2, LAN-3, LAN-4). Speed：Here you can select the speed of the port . Flow control: you can enable the Flow control function or disable it. Default VLAN ID (1-4094): the VLAN ID you want it default. 5.12.
FSW-2104W Multimedia Residential Gateway 5.13.1 Storm Control Figure 5-33 Storm Control • • • • Broadcast Strom：select enable if you want control the speed of Broadcast packets... Multicast Strom control：select enable if you want control the speed of Multicast packets... UL Strom：select enable if you want control the speed of UL packets.. Burst：select the NO. of the packets you want 5.
FSW-2104W Multimedia Residential Gateway 5.14.2 Restart This page (shown in figure 5-36) allows you to reboot the router: Figure 5-36 Reboot Click the Reboot button to restart the router. Some settings of the router will take effect only after rebooting, which include: • • • • • • • Change LAN IP Address. (System will reboot automatically) MAC Clone (system will reboot automatically) DHCP service function. Static address assignment of DHCP server. Web Service Port of the router.
FSW-2104W Multimedia Residential Gateway Figure 5-38 User Name/Password Management It is strongly recommended that you change the factory default user name and password of the router. All users who try to access the router's web-based utility will be prompted for the router's user name and password. Note: The new user name and password must not exceed 14 characters in length and must not include any spaces. Enter the new Password twice to confirm it. Click the OK button when finished.
FSW-2104W Multimedia Residential Gateway 5.15.1 Log This page (shown in figure 5-40) allows you to query the Logs of the router. Figure 5-40 System Logs The router can keep logs of all traffic. You can query the logs to find what happened to the router. Click the Refresh button to refresh the logs. Click the Clean button to clear all the logs.
FSW-2104W Multimedia Residential Gateway Appendix A: Glossary • • • • • • • • • • • • DDNS (Dynamic Domain Name System) – The capability of assigning a fixed host and domain name to a dynamic Internet IP address. DHCP (Dynamic Host Configuration Protocol) - A protocol that automatically configure the TCP/IP parameters for the all the PCs that are connected to a DHCP server.
