Specifications

Appendix A
136
A.14.4 Provisioning by NMC (Telnet)
When placed in the CH20 with NMC, this card can be configured through any of the NMC interfaces, including Telnet, Web
GUI and SNMP.
<1> : Port Active - Use this item to enable or disable the line card. When disabled all transmission will be blocked and all
the line card LED indicators will be Off.
<2> : Baud Rate Select - As a 3R repeater, the device needs to be set to the proper data rate for the intended application.
<3> : Loop Back Function - This is a master loop back item. If this is enabled, the loop back configured in 4&5 is enabled.
If this is disabled, all loop back is disabled, regardless of the setting of 4&5.
<4> : Line Side Loop Back - This initiates the line side (top fiber connector) loop back.
<5> : Client Side Loop Back - This initiates the client side (bottom fiber connector) loop back.
<6> : Line Side Loss Propagation - This enables or disables the Line Side Link Fault Passthru function of the converter.
<7> : Client Side Loss Propagation - This enables or disables the Client Link Fault Passthru function of the converter.
<8> : Line Side Auto Laser Shutdown (ALS) - Enables or disables the ALS safety feature for the Line Side Optical port.
<9> : Client Side Auto Laser Shutdown (ALS) - Enables or disables the ALS safety feature for the Client Optical port.
<A> : Port Reset - This function will clear and reload the CPLD, effectively resetting the port. Data loss will occur when
performing this reset. Use with care.
<B> : Set to default - This returns all settings to factory default.
<C> : Line Side SFP - If an SFP is installed for optical, the information can be viewed here. See below..
<D> : Client Side SFP - If an SFP is installed for optical, the information can be viewed here. See below..
Line Side SFP Status
This Chassis ID:[00] Cascaded:[Yes] Monitored Chassis ID:[00]
SLOT #10 > FRM220-3R/10G-SS [Local] [ Ver:1.100-2.007-1.100-0.000 ]
Line Side Link :[Up ] Line Side CDR Lock :[Locked ] Tx Fail:[Normal]
Client Side Link:[Up ] Client Side CDR Lock:[Locked ] Tx Fail:[Normal]
<1> :Port Active:[Enable ] System Status:[Ok ]
<2> :Baud Rate Select:[1G Fiber Channel ]
<3> :Loopback Function:[Disable]
<4> :Line Side Loopback :[OFF]
<5> :Client Side Loopback:[OFF]
<6> :Line Side Loss Propagation :[Disable]
<7> :Client Side Loss Propagation:[Disable]
<8> :Line Side Auto Laser Shutdown :[Disable]
<9> :Client Side Auto Laser Shutdown:[Disable]
<A> :Port Reset.
<B> :Set to default.
<C> :Line Side Small Form Pluggable(SFP):[Yes] Digital Diagnostic(D/D):[Yes]
<D> :Client Side Small Form Pluggable(SFP):[Yes] Digital Diagnostic(D/D):[No ]
SLOT #10 > FRM220-3R/10G-SS [Local ] [ Ver:1.100-2.007-1.100-0.000 ]
Vendor Name :[ FIBERXON INC. ]
Vendor Part Number:[ FTM-3125C-L40 ]
Fiber Type :[ Single ]
Wave Length :[ 1310nm ]
Wave Length 2 :[ 1310nm ]
Link Length :[ 0040km ]
Tx Power :[ +01dBm ]
Rx Power :[ +08dBm ]
Temperature :[ +047C ]
Rx Sensitivity :[ ------ ]
Power Margin :[ ------ ]