Technical data
34
CTC EcoZenith i250
General Information
8.7 Settings
This is used to set the parameters for operating
the system. It is important that this default setting
is adjusted for your property. Values which are set
incorrectly may mean that your property is not warm
enough or that an unnecessarily large amount of energy
is being used to heat your property.
8.7.1 Heating circuit 1 or 2
Max. primary flow 55(30...80)
The maximum permitted temperature supplied to the
radiators. This functions as an electronic limiter to
protect the floor coils in underfloor heating systems.
Radiator system 2 can only reach the same temperature
as radiator system 1 or a lower temperature.
Min. primary flow Off (Off, 15...65)
You can use this option to set the minimum permitted
temperature if you want a specific level of background
heating during the summer in the basement or
underfloor heating coils, e.g. in the bathroom. The
heating in other parts of your property should then be
switched off using thermostatic radiator valves or shut-
off valves. Note that the radiator pump will then operate
for the whole summer. This means that the temperature
out to the radiators does not fall below a selected
temperature, for example +27°C.
“Off” means that the function is turned off.
Heating off, outside 18(10...30)
Outdoor temperature limit at which the house no
longer requires heating. The radiator pump stops and
the mixing valve is kept closed. The radiator pump
is activated daily for a short period to reduce the risk
of jamming. The system restarts automatically when
heating is required.
Heating off, minutes 120(30...240)
The delay period before the radiator pump stops as
described above.
For example:
“Inclination 50” means that the temperature of the water
supplied to the radiators will be 50°C when the outdoor
temperature is -15°C, if the adjustment is set to 0. If the
adjustment is set to +5, the temperature will be 55°C
instead. The curve is increased by 5°C at all outdoor
temperatures, i.e. the curve is parallel offset by 5°C.
!
Tip: Read more about these settings
in the chapter on Your property’s
heating installation.
Svenska Nederlands English Deutsch
Suomi Française Dansk Norsk
1 2
1 2
22,2 ºC 21,2 ºC 58 ºC -5 ºC
1 2
1 2
1 2
1 2
1 2
T ºC
60
40
20
0
-20
16 20 0 4 8 12
00 - 06 22 - 24
00 - 06 22 - 24
00 - 06 22 - 24
00 - 06 22 - 24
00 - 06 23 - 24
00 - 08 23 - 24
00 - 08 22 - 24
06 - 09 18 - 21
07 - 09 -- - --
08 - 09 -- - --
08 - -- -- - 21
08 - -- -- - 21
10 - 12 20 - 23
10 - 12 20 - 23
Room temp. DHW Operation Installer
CTC EcoZenith Monday 09:35
Night reduction Holiday
Heating circuit 2 (50)
Heating circuit 1
Room temp.
Start menu
Room temperature settings
Selecting DHW comfort
Heating system data
Installer settings menu
Extra
Hot water
0.0 hours
On
Temperature
Normal
Weekly schedule
DHW
Operation data system
Status HP upper tank
Tank upper°C 49 (58)
Tank lower°C 42 (45)
Electric power kW 0.0+2.5
Current L1/L2/L3 0.0 0.0 0.0
Diff func. Pump / ºC On 32
Pool ºC Off 22(20)
Operation data EcoZenith
Stored oper data
Heating circuit
Operation data heating
Installer
Time/Language Settings Define system Service
Software display PCB: 20120205
Software HP PCB: 01234
Installer
Installer
Time 21:34
Date 2012-02-05
Settings
Heating circuit 1
Heating circuit 1
Heating circuit 2
Heat pump
Electric heater
Upper tank
Remote control None
Communication
Solar panels
Diff thermostat function
Pool
Save settings
Load settings
Load factory settings
Max primary flow°C 55
Min primary flow°C Off
Heating off, out°C 18
Heating off 120
Inclination°C 50
Adjustment°C 0
Room temp reduced°C -2
or
Primary flow reduced°C -3
>>
Define system
Def heating circuit 1
Heating circuit 1
Heating circuit 2
Heat pump
CTC SMS
Cooling
Solar panels
Diff thermostat function No
Pool (G50, G51, B50) No
Heating circuit 1 Yes
Room sensor 1 Yes
Type Wire
Service
Function test
Function test
Alarm log
Factory settings coded
Quick start compressor.
Software update, USB
Write log to USB
Control current sensors
Re-installation
Heating circuit
Heat pump
Valves
Electric heater
Solar
Diff thermostat function
Pool
Total operation time h: 14196
Max primary flow°C: 51
Consumtion kWh 20
Compressor:
Total Operation time 1540
Stored oper data
Heat pump
Compressor On
Charge pump On 47%
Brine pump On
HP in/out°C 35.5 / 42.3
Current L1 4.0
Night reduction heat circ.
Weekly program Block NR
Decrease Sunday 22:00
Increase Friday 14:00
Decrease -------- 00:00
Increase -------- 00:00
Holiday
Holiday period 3 days
Out Room1 Prim1 Return Room2 Prim2
Settings language
Night reduction heat circ. 1
Weekly program Day by day NR
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
Weekly program Day by day DHW
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
Weekly program DHW
Svenska Nederlands English Deutsch
Suomi Française Dansk Norsk
1 2
1 2
22,2 ºC 21,2 ºC 58 ºC -5 ºC
1 2
1 2
1 2
1 2
1 2
T ºC
60
40
20
0
-20
16 20 0 4 8 12
00 - 06 22 - 24
00 - 06 22 - 24
00 - 06 22 - 24
00 - 06 22 - 24
00 - 06 23 - 24
00 - 08 23 - 24
00 - 08 22 - 24
06 - 09 18 - 21
07 - 09 -- - --
08 - 09 -- - --
08 - -- -- - 21
08 - -- -- - 21
10 - 12 20 - 23
10 - 12 20 - 23
Room temp. DHW Operation Installer
CTC EcoZenith Monday 09:35
Night reduction Holiday
Heating circuit 2 (50)
Heating circuit 1
Room temp.
Start menu
Room temperature settings
Selecting DHW comfort
Heating system data
Installer settings menu
Extra
Hot water
0.0 hours
On
Temperature
Normal
Weekly schedule
DHW
Operation data system
Status HP upper tank
Tank upper°C 49 (58)
Tank lower°C 42 (45)
Electric power kW 0.0+2.5
Current L1/L2/L3 0.0 0.0 0.0
Diff func. Pump / ºC On 32
Pool ºC Off 22(20)
Operation data EcoZenith
Stored oper data
Heating circuit
Operation data heating
Installer
Time/Language Settings Define system Service
Software display PCB: 20120205
Software HP PCB: 01234
Installer
Installer
Time 21:34
Date 2012-02-05
Settings
Heating circuit 1
Heating circuit 1
Heating circuit 2
Heat pump
Electric heater
Upper tank
Remote control None
Communication
Solar panels
Diff thermostat function
Pool
Save settings
Load settings
Load factory settings
Max primary flow°C 55
Min primary flow°C Off
Heating off, out°C 18
Heating off 120
Inclination°C 50
Adjustment°C 0
Room temp reduced°C -2
or
Primary flow reduced°C -3
>>
Define system
Def heating circuit 1
Heating circuit 1
Heating circuit 2
Heat pump
CTC SMS
Cooling
Solar panels
Diff thermostat function No
Pool (G50, G51, B50) No
Heating circuit 1 Yes
Room sensor 1 Yes
Type Wire
Service
Function test
Function test
Alarm log
Factory settings coded
Quick start compressor.
Software update, USB
Write log to USB
Control current sensors
Re-installation
Heating circuit
Heat pump
Valves
Electric heater
Solar
Diff thermostat function
Pool
Total operation time h: 14196
Max primary flow°C: 51
Consumtion kWh 20
Compressor:
Total Operation time 1540
Stored oper data
Heat pump
Compressor On
Charge pump On 47%
Brine pump On
HP in/out°C 35.5 / 42.3
Current L1 4.0
Night reduction heat circ.
Weekly program Block NR
Decrease Sunday 22:00
Increase Friday 14:00
Decrease -------- 00:00
Increase -------- 00:00
Holiday
Holiday period 3 days
Out Room1 Prim1 Return Room2 Prim2
Settings language
Night reduction heat circ. 1
Weekly program Day by day NR
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
Weekly program Day by day DHW
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
Weekly program DHW