RGBHV Video with Stereo Audio USER’S MANUAL Models 7220 and 7221 WORLD HEADQUARTERS 55 Cabot Court Hauppauge, N.Y. 11788 USA Tel: (631) 273-0404 Fax: (631) 273-1638 www.commspecial.com Email: info@commspecial.com Communications Specialties Pte Ltd 100 Beach Road #22-09 Shaw Tower Singapore 189702 Tel: +65 6391 8790 Fax: +65 6396 0138 Email: csiasia@commspecial.com P/N: 122995 Rev.
CONTENTS General Information ................................................... 3 Introduction ............................................................ 3 Technical Specifications ......................................... 3 Installation Instructions .............................................. 5 Installation Procedure ............................................. 6 System Connections ............................................... 6 Alarm Switch Settings ............................................
The status of the VIDEO and AUDIO indicator LEDs should provide the first clue as to the origin of an operational failure. If these are off, it usually means that the fiber is broken or has too much attenuation. Next, be certain that the input and output signal connections are correct. Finally, although multimode and single mode devices may look the same, they will not operate properly together.
Signal Connectors ................................ HD-15F RGB Processing ................................... 24 bits, no compression or scaling Audio: Number of Audio Channels .................. 2, unbalanced Frequency Response ............................. +0/-0.5 dB, 20 Hz to 20 kHz Input Impedance ................................... >24 k Ohms Output Impedance ................................ <1 Ohm Maximum Audio Level ........................ +10 dBu THD+N ...............................................
provides an output to drive a model 6020 Alarm Sensing Module which provides an audible tone and activates a set of contacts for external signaling purposes. The status of the LEDs are as follows: TRANSMITTER and RECEIVER: Power: ON: (GREEN) Indicates that correct power has been applied. TRANSMITTER: Video: OFF: Indicates no video detected on the input. BLINKING GREEN: Indicates either H or V sync detected at the input but not both. STEADY GREEN: Indicates both H and V sync detected on the input.
5. Apply power to both Pure Digital Fiberlink® units. For box versions using DC power connections, refer to Figure 1. 6. When power is applied, the green POWER LED will light, indicating the presence of operating power. The VIDEO LED will give an indication as described on Page 8. 7. The green AUDIO LED will give an indication as stated on Page 8. System Connections - “Video Pin Out” continued: Video Pin Outs: Transmitter Receiver 8 Ground Ground 9 N/C N/C 10 Ground Ground 11 N/C N/C 12 N/C N/C 13 Hor.
5. Apply power to both Pure Digital Fiberlink® units. For box versions using DC power connections, refer to Figure 1. 6. When power is applied, the green POWER LED will light, indicating the presence of operating power. The VIDEO LED will give an indication as described on Page 8. 7. The green AUDIO LED will give an indication as stated on Page 8. System Connections - “Video Pin Out” continued: Video Pin Outs: Transmitter Receiver 8 Ground Ground 9 N/C N/C 10 Ground Ground 11 N/C N/C 12 N/C N/C 13 Hor.
provides an output to drive a model 6020 Alarm Sensing Module which provides an audible tone and activates a set of contacts for external signaling purposes. The status of the LEDs are as follows: TRANSMITTER and RECEIVER: Power: ON: (GREEN) Indicates that correct power has been applied. TRANSMITTER: Video: OFF: Indicates no video detected on the input. BLINKING GREEN: Indicates either H or V sync detected at the input but not both. STEADY GREEN: Indicates both H and V sync detected on the input.
Signal Connectors ................................ HD-15F RGB Processing ................................... 24 bits, no compression or scaling Audio: Number of Audio Channels .................. 2, unbalanced Frequency Response ............................. +0/-0.5 dB, 20 Hz to 20 kHz Input Impedance ................................... >24 k Ohms Output Impedance ................................ <1 Ohm Maximum Audio Level ........................ +10 dBu THD+N ...............................................
The status of the VIDEO and AUDIO indicator LEDs should provide the first clue as to the origin of an operational failure. If these are off, it usually means that the fiber is broken or has too much attenuation. Next, be certain that the input and output signal connections are correct. Finally, although multimode and single mode devices may look the same, they will not operate properly together.
LIMITED WARRANTY Communications Specialties, Inc. (CSI) warrants that for a period of three years after purchase by the Buyer, the Pure Digital Fiberlink® 7220 Series transmission System will be free from defects in material and workmanship under normal use and service. A Return Material Authorization (RMA) number must be obtained from CSI before any equipment is returned by the Buyer.
