User`s guide

ManualsBrandsCSG Security ManualsComputer equipmentNVeDVR

281

282

283

284

285

286

287

288

289

290

280 VEREX Director V4.73 User's Guide 21-0381E v4.7.3

Output Points and Related Settings

Output points are programmable elect ronic

switches that can be used t o signal alarm s or

control items such as lights, garage doors, etc.

The Output P oints screen allo ws vie wing or

changing the characteristics for each of these

outputs.

Power: Outputs provide a switching function only

(devices must include a suitable power source).

Map/Graphic Annunciator Modules

: Outputs on a

"Map" module pertain to firing the LEDs on the module

itself rather than external devices.

Exception: Outputs 1 and 2 on a map module can

each fire an LED and are also provided on the board

(OP1=+V/High; OP2=0V/Low).

Door Controllers and Suite-Security Keypads

: These

devices have built in dedicated outputs that are set up

directly under "Doors" or "Suite Security".

Special Features and Complex

Equations

Beginning with V4.2, outpu t programming has

been greatly enhanced, including:

• Any output function can be set as a positive

trigger (Normally 0V/Low; +V/High when

triggered), or negative trigger (Normally

+V/High; 0V/Low when triggered);

• In addition to steady operation, three On/Off

cadence selections are provided;

• Outputs can be triggered by just about any

type of event(s)--including the new activity-

monitoring and user-counting features.

• Complex equations can be set up using

"Boolean" operators (AND, OR, XOR, etc.)

General Signalling Functions

Outputs can be set to activate whenever a

certain type of input is trigg ered or a specific

event occurs. This can be associated with a

desired panel ("System"), o r a specific "Area",

holiday, or device.

Keypad Function Keys

The function-key feature allo ws settin g up

actions to occ ur w hen a us er presses the “ƒ”

and a number at an 'LCD keypad'. This

pertains to outputs set to "Function Key X".

ƒ1-ƒ5 are available to all users, while ƒ6-ƒ9 and ƒ0 can

be set (on an area-by-area basis) to require a user with

“Function Key” authority to log in before the keys will

work. For details, see the "Require Function Key PIN"

selection under "Areas and Related Settings".

Function key ƒ5 is pre-set to toggle the keypad chime

feature on and off. It can be programmed for other

actions, but is generally not—since the keypad chime

feature would be toggled as well.

The Numeric Paging Feature

UK/ACPO: This feature is not supported with

UK/ACPO operation.

Also See

: [Management], ÖSerial Reporting.

 Software-Based Text Paging (Serial Reporting)

Outputs 5-8, or 5-8 & 121-128 (see e xception)

can be set t o signal a nu meric pager when

triggered by their associated alarm condition.

Exception: Beginning with V4.4 (software and

firmware), the outputs to use for numeric paging are

configurable.

: Configuration, ÖSystem, ÖI/O Mapping 

 I/O Mapping  (under "General System Settings

for a Panel").

Outputs 005 - 008

: These are 'virtual' outputs that are

not associated with any physical wiring).

The specific a larm/event to be associated with

each of the outputs is define d here, while other

settings for the paging feature are set th rough

the System Communication screen.

For details,

refer to "Monitoring, Paging, & Remote Mgt. Settings".

Parallel STU / REDCARE and VBUS

Outputs

Outputs pertaining to a Subscriber Terminal

Unit (STU) interface (and also regarding VBUS

operations) need to be reserved ahead of time.

Select Outputs: Configuration, ÖSystem, ÖI/O

Mapping ;  I/O Mapping  (under "General

System Settings...", previous).

How to Get Here

Multi-Account Systems: First select [Account Folders]

in the 'tree', and locate and double-click the desired

account.

MyTools Bar: Output Points

In the Tree

: Configuration (click the "+"),

ÖOutput Points

(Under the specific panel group and

panel--if listed in the 'tree'.)