User`s guide

21-0381E v4.7.4
Welcome Report Control Admin
Sys Config Tech-Ref
205
- Module type when last communicated:
During each communications session with the
panel, the module types are checked and
displayed here;
 I/O (for modules that support inputs and
outputs)

- Inputs: The number of input points (monitored
sensors) supported by this module;
Note: The first 3 inputs on a system LCD keypad
pertain to the built-in emergency keys rather than
external sensors.
Director V4.4
: Input points associated with newer-
style modules use custom input circuits. (Related links
follow).
 Configuration, Input Points, Custom Circuit
 Custom Circuit-Types for Input Points
 Configuration, Input Points
 Input Points—Monitored Sensors
- Outputs: The number of outputs
(programmable electronic switches) on the
device;
Note: Outputs on a "Map" module pertain to firing the
LEDs on the module itself rather than triggering
external devices.
-------------------------
- Input Range: The input point numbers to be
associated with this expansion module.
- Output Range: The range of programmable
output-point numbers to be associated with this
expansion module.
Input and Output Range: The Number-Range for inputs
& outputs is based on the number of inputs and outputs
supported by each module, and the order the modules
are installed--plus the "Display Offset" settings for the
specific panel. For details on the "Display Offset" value,
refer to "System Panels and Displayed Item-Numbers".
 Keypad (settings for LCD Keypads) 
- Assigned to Area: The 'area' that this keypad is
associated with;
- Exit Delay When Arming: Whether or not an
exit delay is to be in effect when arming the
keypad's area to 'Stay' and/or 'On'. (Arming any
other areas from this keypad will be immediate).
'Stay' pertains to 'perimeter' sensors being monitored,
and 'On' pertains to all sensors in the area being
monitored.
- Entry and Exit Tones on Stay Mode: Whether
or not Entry/Exit tones are to be sounded at this
keypad while the associated area is set to the
STAY arming level.
- Annunciation (1
st
bar of Areas): The area(s)
to be monitored by this keypad (i.e., the areas
for which any alarms will be signalled at the
sonalert built into this keypad).
Tip: As you move across the 'bar' of area symbols,
the name of each area will be shown on the right—
allowing you to pick the correct ones. Alternatively,
click the pencil symbol and then select desired areas
from the small screen that appears.
- Arming/Disarming (2
nd
bar of Areas --V4.4):
The area(s) that can be armed and disarmed
from this keypad (by users with appropriate
authority);
Also See: 'Tip', previous/above.
Note: This pertains to individual areas, as well as
specific areas within defined 'Area Groups'.
- Exit Delay (3
rd
bar of Areas --V4.4): The
area(s) for which the exit delay is to be signalled
at this keypad;
Also See: 'Tip', previous/above.
- Default Display Mode
(V4.4): This sets what
is normally displayed on this keypad's display
(i.e., date only, or alternate between the date
and the presently defined "System Message".
Related: Configuration, System, Standard 
 General System Settings for a Panel
- Armed LED Display (V4.4): Whether arming
state will always be indicated via LEDs, or only
for a pre-set duration;
- Arming Tone Mode
(V4.4): This sets whether
entry and/or exit tones will be signalled at this
keypad;
- Auto Silence Disarm Mode
(V4.4): Allows
setting the keypad to auto-silence and/or have
all of the user's authorized areas disarm
automatically when someone logs into this
keypad;
- Verify User Mode
(V4.4): Enables and
configures the 'verify user' mode/operation (i.e.,
whether or not users will have to enter their PIN
after silencing an alarm);
 Badge  (V4.4)
User Badging Mode
- Schedule: Select a schedule here to allow card
badging features to be different during a
schedule vs. after-hours.