Datasheet

Document NO.: WI-FHF- CS-SBA015SL-A Page 7of 9
MODEL: CS-SBA015SL
REV : A/1
Date : 03 Jun 2017
8
Vibration Proof
Capability
抗振动性能
Set the vibration testing machine on
F=20HZ, I=90%, T=30min. Record the
discharging capacity after test.
实验过程中将振动仪设置在 F=20HZ；
I=90%；T=30min 实验后记录电池的 1C 放
电容量
1) After test, 1C capacity should be no
less than 85% of it before test
Internal resistance discrepancy
should be no more than 3mΩ.
实验后的 1C 容量≥实验前 98%，
内阻相差不超过 3mΩ.
2) Battery appearance should not be
obvious nick, leak, smoke and burst.
电池外观应无明显损伤、漏液、冒
烟或爆炸
9
Fall Proof Capability
抗跌落性能
Hang the battery in one meter high in the
air. Let the cells fall down by six sides
将电池悬空在 1 米高处，将电芯自由跌
(Anode and Cathode side，crosswise sides）
1 time each，all together 6 times.
落 6 面（正负极面，横向面）各 1 次，共 6 次。
1）
Battery should not be leak, smoke
and burst.
电池应不漏液、不冒烟、不爆炸
3) After test, 1C capacity should be
no less than 95% of it before
test. Internal resistance
discrepancy should be no more
than 3mΩ.
实验后的 1C 容量≥实验前 95%，内
阻相差不超过 3mΩ。
10
Capacity Retention
电荷保持能力
1) In environmental temperature 20℃± 5
℃ condition, Use nominal capacity
charging method full charge the battery
在环境温度 20℃±5℃条件下, 按标
称容量充电方法将电池充饱电
2) Lay the battery opened circuit 28D,
then use 0.2C discharge it to cut off
voltage
将电池开路搁置 28D,再以 0.2C 放电至终
止电压
0.2C discharging time should no less than
3.20H.
0.2C 放电时间应不低于 3.20H.
11
Constant Temperature and
Humidity Proof Capability
抗恒定湿热性能
Lay the battery in temperature 40±2℃ and
humidity 90% ~ 95% environmental chambers
for 48h. Then lay the battery in
environmental temperature 20±5℃
condition for 2h. Later discharge it in 1C
and record the capacity.
将电池放入 40℃±2℃，相对湿度为 90%
～95%的恒温恒湿箱中搁置 48h 后，将电
池取出在环境温度 20℃±5℃的条件下
搁置 2h，以 1C 放电，并记录容量。
1) Battery appearance should not be
obvious nick, leak, smoke and burst.
电池外观应无明显变形锈蚀、冒烟
或爆炸.
2) 1C discharging capacity should no less
than 36min. Internal resistance
discrepancy should be no more than
3mΩ.
1C 放电容量应≥36min,内阻相差不
超过 3mΩ。
3.4.
Shipping Voltage (Inspection before shipment): ≥2.4V
出货空载电压(出货前检测): ≥2.4V