Swift800 Pro SDI & HDMI Wireless Video SHENZHEN CRYSTAL VIDEO TECHNOLOGY CO.,LTD USER MANUAL ADD: F12, F518 Idea Land, Baoyuan Road, Baoan Central Area,Shenzhen, China Post code：518102 Fax: +86-755-29188427 Tel: +86-755-27750518-6652 www.cv-hd.com E-mail: Sales@cv-hd.com E-mail: Marketing@cv-hd.com This user manual applies to: Transmitter: 7103 Receiver: 3103 Version: 1.0 2020.05.
Optimal range between transmitter and receiver is between 1 meter and 30 meters with in line of sight indoor
CONTENTS CONTENTS User Operation Instructions 01 About This Manual 01 Product Introduction 01 Connectivity diagram 02 Packing List 04 Product Interface Introduction 05 Transmitter Interface Introduction 05 Receiver Interface Introduction 07 Product Installation Operation Instructions 09 Powering on and booting up 12 OLED Screen 13 Button Function Instructions 15 How to Use the App 17 Product Specifications 18 Reminders 19 Troubleshooting 21
Connectivity diagram User Operation Instructions Thank you for choosing CVW’s professional wireless high-definition video and audio transmission product. Before using this product, please carefully read the following reminders: * Avoid exposing this product to direct sunlight or dusty places for a long period of time This product includes a transmitter and a receiver. The transmitter supports HDMI input or SDI input and output.
Product Highlights Deliver quality and low latency video transmission Packing List The standard parts are listed below. Support HD-SDI & 3G-SDI input/output and full-HD input/output via HDMI with a resolution up to 1080P60Hz. The built-in H.264 codec delivers smooth video with latency as low as 70ms. Beamforming transmission distance, and anti-interference capabilities Point-to-Point Mode and RTSP Streaming Mode Support two kinds of working modes: point-to-point and RSTP streaming.
Product Interface Introduction Transmitter 7103 Transmitter 7103 Interface Instructions TX:7103 Serial Number Explanation A A SMA jacks for connectors B B Low Battery Indicator C C Power Button D OLED Screen E CH Button F MODE Button G HDMI In H DC In I Type-C USB Port J SDI Loop Out K SDI In L NP-F Battery Slot D TX E F SWIFT 800 PRO G H USB L I LOOP OUT J K 05 06
Receiver 3103 Interface Instructions: RX:3103 Receiver 3103 Interface Introduction Serial Number A Explanation A SMA jacks for connectors B B Low Battery Indicator D C Power Button E D OLED Screen E CH Button F MODE Button G HDMI Out H DC In I Type-C USB Port J SDI Out K SDI Out L NP-F Battery Slot C F SWIFT 800 PRO G H USB I L J K 07 08
Product Installation Operation Instructions 1. Please install the antennas on the receiver and transmitter via the antenna port. There should be a 90° angle between each antenna (the optimal installation method) as shown in the picture. Battery SWIFT 800 PRO 90 3. Install the transmitter and receiver on the camera using the 1/4 screw hole on the bottom or the L-shaped mount 2.
4. Use the HDMI or SDI cable to connect the transmitter to the camera. Powering on and booting up 1. Power the transmitter and receiver with three ways as follows a) Install the NP-F battery in the NP-F battery holder on the back of the transmitter. b) Use the attached DC power adapter c) Use a V-mount battery (USB-D to DC power cable is needed in this case). d) Use a power bank (5V/2A) with Type-C cable SWIFT 800 PRO SDI In 2. Booting up the transmitter and receiver requires about 30 seconds.
OLED Screen SSID Model: 7103+3013 Fan Status Video Signal NO VIDEO Battery Charge Network Signal NO VIDEO Working Mode 930333 CH 1 Video Signal Operating Frequency RTSP CH 1 Operating Frequency Battery Charge: (Displayed only when using Sony NP-F batteries to supply power) Fan Status: (When the fan is on, displays rotating fan blades; when the fan is off, displays non-rotating fan blades) Network Signal: (When the network is not connected, displays ‘X’; When the network successfully connects, d
Button Function Instructions Mode Switching 1. Switching operation must be applied on both the transmitter and receiver. CH Button 2. Factory mode is point-to-point mode Press this button to switch channels. 3.
Product Specifications How to Use the App 1. Download the App App download method can be obtained at www.cv-hd.com Item TX: 7103 RX: 3103 Frequency 5.10~5.80 (GHz) Video Format 1080psf24/23.98(SDI In) 1080i60/59.94, 1080i50, 1080p60/59.94 , 1080p50 , 1080p30/29.97, 1080p25 , 1080p24/23.98 , 2. Install App 720p60/59.94 , 720p50, 480P, 576P, 480i, 576i 3. Switch the product to RTSP working mode 4. Open the app, click the app’s linked icon, and choose the corresponding SSID number.
Reminders Installing Height and Interval Distance Cable Connection a) First connect the video signal cord, and then turn on the power supply. b) During normal usage, avoid hot swapping the video signal cords. 1. In wide-open and unobstructed conditions, and when using the most optimal installation methods for antennas, this product’s transmission distance can reach Product and Antenna Installation 250 meters.
Troubleshooting 1. The transmitter and receiver cannot establish a connection. a) Check whether the product’s antenna has been installed correctly. b) Check whether the power adapter or battery input comply with the product specification requirements. c) Check whether the product can boot up normally, and whether the display screen can display normally. d) Check whether the product’s transmitter and receiver’s working mode are matched.
