Wireless Video Link Zero Latency PRO 300 Plus User Manual Model:7059+3059 Version:1.1 2018.12.
About the User Manual - Please read this manual carefully before you use this product and retain it properly for future reference. Contents - If there is any question or difficulty about the operation of product, please feel free to contact us or the dealer.
Packing List Specification Please check the package inside to assure it contains the parts as below, if any parts missed, please contact the distributor or us. Transmitter Transmitter * 1 V-Mo unt * 1 *Opt ional Antenna * 2 Power Cable * 1 2-Pin Lemo to D-Tap Specification Item Frequency 5.1~5.9GHz Bandwidth 40MHz Video Formats 1080P 23.98/24/25/30/50/60 1080i 50/59.
Interface Information Transmitter Interface Transmitter Interface Description Model：7059 Specification Item 5.8G Antenna Interface LED Digits Display OK Button CH Button LED Digits Display Display the working channel 1~9, A(10), b(11) OK Button Confirm the function selection CH Button Switch the working channel Mini USB Be used for software upgrading HDMI IN HDMI IN SDI IN SDI IN Mini USB HDMI in Power input interface (LEMO): support 7V to 36V V-MOUNT DC-IN SDI in DC-IN 5.
Receiver Interface Model：3059 Receiver Interface Description 5.
TX Product Installation Transmitter Installation Steps: 1. Fix the antennas and adjust their angles as shown in the figure below. (For details, please refer to the transmission distance description.) 3. Turn on the power switch to start power supplying. Power Switch: ON turn on OFF turn off 4.Press “CH” button to select the corresponding working channel of receiver and then press “OK” button for confirmation.
RX Receiver Installation Steps: 3. Turn on the power switch to start power supplying. 1. Fix the antennas and adjust their angles as shown in the figure below. Power Switch: ON turn on OFF turn off Notice: please rotate the golden mental part of antenna to fasten the antenna. 4. Press “CH” button to select the corresponding working channel of receiver and 2. Connect RX with the monitor via corresponding power cable and HD video cables as shown in the figure below.
5. RX supports switching between normal mode and enhanced antiinterference mode according to transmission distance and interference level LED Digits Display description LED Digits Display Status a) Switch from normal mode to enhanced anti-interference mode: long press “OK” for longer than 3 seconds to enter enhanced anti-interference mode, and decimal point of digital tube (indicator) starts to flash slowly.
Application Recommendations Receiver LED Digits Display: Channel 1 ~ 9, A, b Application Recommendations Video Indicator: HDMI and SDI outputs are enabled together, there are two status of the indicator 1：Red and Yellow light together: RX receives the signal from TX normally, and HDMI and SDI outputs are working together In order to reach the best performance of wireless transmission, we recommend to meet the requirements as follows: 1. The vertical height of TX and RX should be same and more than 1.
2.Recommended Installation Method under Non-ideal Position When the front side of the transmitter is not able to face to the receiver, Please make receiver to stand vertically; adjust antennas to a fan-shaped arrangement; Make transmitter to stand vertically; adjust the right side of the 2 transmitter antennas towards backside by 45°. Antenna Pattern 2: Right side 45° angle rotation towards backside 3.
Trouble shooting Display“Link Connecting” Audio Image displayed,No audio Video source mute Turn on the audio of video source Volume too low Turn up the audio of video source Audio format not supported Switch the format of video source output Something wrong with transmitter/ receiver Restart the transmission kit *For more questions, please contact the distributor or us.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and usedin accordance with the instructions, may cause harmful interference to radio communications.
