Information

DP Series
Complete specifications of these & other Crydom products available at: www.crydom.com
Convenient FET switches in H-Bridge configuration
Control features to combine Soft Start/Ramp Up, Soft Stop/Ramp Down & Braking functions on
each polarity
Built-in protective Forward/Reverse interlock function
20 , 40 & 60 Amps Operational Current rating
48 VDC Rated Operating Voltage
UL & IEC ratings for general use & Motor loads
4.5 to 15 VDC & 18 to 32 VDC Input Control Voltage options available
LED Status indicators for Operating Modes
Industry standard 75 x 105 mm Panel Mount package
DP Series
DC Load Reversing Solid State Contactors
70
60
30
40
50
20
10
20 30 40 50 60 70 80
0
Ambient Temperature (ºC)
Load Current (Amps)
DP4Rxx60x60xx
DP4Rxx60x40xx
DP4Rxx60x20xx
General Notes
(A) All parameters at 25ºC unless otherwise specified.
(B) Maximum Surge Current rating not to be exceeded during motor Starting or Dynamic Braking.
(C) For maximum ratings use heat sink ratings in TABLE 1.
(D) Input circuit incorporates active current limitation.
(E) Suggested mating connector/plug : Crimp Housing, Positive Latch (Molex 050579404).
Derating Curves
Required Heat Sink
[ºC/W]
TABLE 1
DP Series
Part No.
Crydom Heat Sink
Part No.
1.5 HS103 / HS103DR
1.0 HS103 / HS103DR
0.5
DP4Rxx60x20xx
DP4Rxx60x40xx
DP4Rxx60x60xx HS053
Output Specifications DP4Rxx60x20xx DP4Rxx60x40xx DP4Rxx60x60xx
DP4Rxx60D40xx DP4Rxx60E40xx
DP4Rxx60x20xx DP4Rxx60x40xx DP4Rxx60x60xx
Operating Voltage Range [VDC]
Rated Operating Voltage [VDC]
Maximum Off-State Leakage Current @ Rated Voltage [µA]
Minimum Load Current [A]
Maximum Surge Current (10 ms) [ADC]
Maximum On-State Voltage Drop @ Rated Current [VDC]
Combined Thermal Resistance Junction to Case (Rjc) [°C/W]
Total Power Dissipation per module, 2 FET switches conducting, Tj=100º C [Watts]
UL 508 General Use Load Current @ Rated Voltage [A]
UL 508 Motor Controller Load Current @ Rated Voltage [FLA]
IEC 60947-4-1 DC-1 Load Current @ Rated Voltage [ADC]
IEC
60947-4-1 DC-3 Load Current @ Rated Voltage [FLA]
Input Specifications
Logic Supply Voltage Range (pin 5) [VDC] 4.5 - 15 18 - 32
16/20 20/25Min/Max Logic Supply Current (pin 5) [mA]
Control Voltage Range (pin 7, pin 8) [VDC] 4.5 - 15 18 - 32
0.20 1
1 2
Minimum Control Input Current @ Min voltage (pin 7, pin 8) [mA]
Maximum Control Input Current @ Max voltage (pin 7, pin 8) [mA]
Typical Interlocking Time [msec]
General Specifications
Dielectric Strength, Input-Output to Baseplate (50/60Hz) [Vrms]
Minimum Insulation Resistance @ 500 VDC [Ohm]
Maximum Capacitance, Input to Output [pF]
Ambient Operating Temperature Rang
e [ºC]
Ambient Storage Temperature Range[ºC]
Housing Material (Shell)
Encapsulation
Weight (typical) [oz] (gr)
Input Locking Connector
Output Terminals
Maximum Torque [in-lbs] (Nm)
Wire Size for Maximum Ratings (with terminals)
IP rating
LED Status Indicator
IEC 61000-4-2 : Electrostatic Discharge
IEC 61000-4-4 : Electrically Fast Transients
IEC 61000-4-5 : Electrical Surges
0.100.10 0.10
0.28 0.28 0.3
Level 2
Level 2 - Criteria A
IEC 60068-2-6 : Vibration
IEC 60068-2-27 : Shock
Compliant (1.5 mm / 10-55 Hz)
Compliant (15 G / 11 ms)
Level 2 - Criteria B
Green LED (Forward), Yellow LED (Reverse). See TABLE 2
IP00
-40 to 125
Thermally conductive
Epoxy
-30 to 80
20 (2.2597)
AWG #12 (IEC 3.3 mm
2
) AWG #8 (8.4 mm
2
)
1-60 1-601-60
48 48 48
20 2020
Black, UL 94 V-0
Rectangular Header, Male Pin 4 Positions, 0.100 in [2.54] Pitch
20 40
Internal PWM For Soft Start/Stop Versions (Duty Cycle 10-100%) [Hz] 200 200200
60
20 40 60
20 40 60
13 14 15
13 14 15
140 24080
0.2 0.130.4
AWG #6 (IEC 13.3 mm
2
)
Input Connector Wire Capacity AWG #24 (0.2 mm
2
)
25 (2.8246)
Screw / Clamp Combo Type 10-32 Hex Screw Type 1/4-20 with lock washers
10.93 (310) 12.16 (345)
(D)
(E)
(A)
(C)
(B)
(C)
(C)
(C)
(C)
(A)
(A)
2500
10
9
28
200200
Maximum On-State Resistance, per FET switch (RDS-ON) [Ohm] 0.0070.014 0.005