Datasheet

ManualsBrandsCRYDOM ManualsSolid State RelaysSolid State Relay, DC Output

DataSheet

Panel Mount

1-DC Series

• Ratings from 60A to 100A @ 100 VDC

• Mosfet Output

• UL Approved, CE Compliant to EN60950-1

• Improved SEMS screw and washer

• Redesigned housing with anti-rotation barriers

For Generation 3 datasheet click here

• DC control

• EMC Compliant to Level 3

• Epoxy Free Design

PRODUCT SELECTION

Control Voltage 60A 80A 100A

3.5-32 VDC D1D60 D1D80 D1D100

AVAILABLE OPTIONS

Required for valid part number

For options only and not required for valid part number

Not all part number conbinations are available.

Contact Crydom Technical Support for information on

the availability of a specific part number.

Series

Operating Voltage

1D: 1-100 VDC

Rated Load Current

60: 60 Amps

80: 80 Amps

100: 100 Amps

601D

Termination

Blank: Screws & clamps

K: Installed standoffs with

screws for PC Board

mounting

OUTPUT SPECIFICATIONS

(1)

Description 100A80A60A

Recommended Operating Voltage [Vdc] 1-72 1-72 1-72

Absolute Maximum Rating [Vdc]

100 100 100

Maximum Off-State Leakage Current @ Rated Voltage [mA] 0.1 0.2 0.3

Maximum Load Current [Adc]

(2) 60 80 100

Minimum Load Current [mA]

(3) 5 5 5

Maximum Surge Current (10 msec)[Adc] 180 220 330

Maximum On-State Voltage Drop @ Rated Current [Vdc] 0.6 0.7 0.5

Maximum On-State Resistance [RDS-ON][Ohms] 0.01 0.008 0.005

Thermal Resistance Junction to Case (Rjc) [°C/W] 0.34 0.34 0.27

Minimum Heat Sink for Rated Current @ 40°C [°C/W] 1 0.5 0.5

Maximum Pulse Wide Modulation Frequency [Hz] (4) 1000 900 800

INPUT SPECIFICATIONS

(1)

Description DC Control

Control Voltage Range 3.5-32 VDC

Maximum Reverse Voltage -32 VDC

Minimum Turn-On Voltage (5) 3.5 VDC

Minimum Turn-Off Voltage 1 VDC

Minimum Input Current (for on-state) 10 mA

Maximum Input Current 15 mA

Nominal Input Impedance Current Regulated

Maximum Turn-On Time [µsec] 100

Maximum Turn-Off Time [µsec] 100

Do not forget to visit us at: www.crydom.com

Summary of content (7 pages)

PAGE 1
Panel Mount DataSheet 1-DC Series • Ratings from 60A to 100A @ 100 VDC • Mosfet Output • UL Approved, CE Compliant to EN60950-1 • Improved SEMS screw and washer • Redesigned housing with anti-rotation barriers • DC control • EMC Compliant to Level 3 • Epoxy Free Design For Generation 3 datasheet click here PRODUCT SELECTION Control Voltage 60A 80A 100A 3.
PAGE 2
Panel Mount DataSheet GENERAL SPECIFICATIONS (1) Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range (6) Ambient Storage Temperature Range Weight (typical) Housing Material Baseplate Material Input Terminal Screw Torque Range (in-lbs/Nm) Load Terminal Screw Torque Range (in-lbs/Nm) SSR Mounting Screw Torque Range (in-lbs/Nm) Input/Load Terminal Screw Torque Range (in-lbs/Nm)
PAGE 3
Panel Mount DataSheet MECHANICAL SPECIFICATIONS (1) Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] Screw Termination 1.1 [27.9] 0.49 [12.4] 1 1.88 [47.6] OUTPUT INPUT 1.1 [27.9] 0.49 [12.4] 0.89 [22.6] Mounting Hole/Slot 0.19 [4.9] DIA. +2 1 1.7 [43.2] S O L I D S TAT E R E L AY 4 Hex Standoff Termination (“K” Option) (7) 2.25 [57.3] 1.88 [47.6] +3 OUTPUT Mounting Hole/Slot 0.19 [4.9] DIA. +2 INPUT 1.0 [25.4] 1.0 [25.4] 1.75 [44.5] 1.75 [44.
PAGE 4
Panel Mount DataSheet SURGE CURRENT INFORMATION Single Pulse (i) Duty Factor (10%) (ii) D1D60 350 Surge Current (Amp) Surge Current (Amp) 300 250 200 150 100 50 0 1 0.1 10 100 Duty Factor (50%) (ii) Duty Factor (20%) (ii) D1D80 600 550 500 450 400 350 300 250 200 150 100 50 0 0.1 1000 1 10 Surge Duration (msec) 100 1000 Surge Duration (msec) D1D100 800 Surge Current (Amp) 600 400 200 0 0.
PAGE 5
Panel Mount DataSheet AGENCY APPROVALS EN60950-1: Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7: IEC 61000-4-2 Electrostatic Discharge Level 3 IEC 61000-4-4 Electrically Fast Transients Level 3 IEC 61000-4-5 Electrical Surges Level 3 E116950 1-DC Series has Environmental Product declarations type III conforming to ISO 14025.
PAGE 6
Panel Mount DataSheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo.
PAGE 7
Panel Mount DataSheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.