Datasheet

ManualsBrandsCrucial Manualscomputers & electronicsMTFDDAK400MAN-1S1AA

P400m 2.5-Inch SATA NAND Flash SSD

MTFDDAK100MAN-1S1AA, MTFDDAK200MAN-1S1AA,

MTFDDAK400MAN-1S1AA

Features

• Micron

25nm MLC NAND Flash

• RoHS-compliant package

• SATA 6 Gb/s interface

• ATA modes supported

– PIO mode 3, 4

– Multiword DMA mode 0, 1, 2

– Ultra DMA mode 0, 1, 2, 3, 4, 5

• Enterprise sector size support

– 512-byte

• Hot-plug capable

• Native command queuing support with 32-com-

mand slot support

• ATA-8 ACS2 command set compliant

• ATA security feature command set and password

• Security erase command set: fast and secure erase

• Self-monitoring, analysis, and reporting technology

(SMART) command set

• 100GB performance (steady state)

1, 2

– Sequential 64KB read: 380 MB/s

– Sequential 64KB write: 200 MB/s

– Random 4KB read: 52,000 IOPS

– Random 4KB write: 21,000 IOPS

– READ latency: 0.57ms

– WRITE latency: 2ms

• 200GB performance (steady state)

1, 2

– Sequential 64KB read: 380 MB/s

– Sequential 64KB write: 310 MB/s

– Random 4KB read: 54,000 IOPS

– Random 4KB write: 26,000 IOPS

– READ latency: 0.51ms

– WRITE latency: 2ms

• 400GB performance (steady state)

1, 2

– Sequential 64KB read: 380 MB/s

– Sequential 64KB write: 310 MB/s

– Random 4KB read: 60,000 IOPS

– Random 4KB write: 26,000 IOPS

– READ latency: 0.51ms

– WRITE latency: 2ms

• Reliability

– Mean time to failure (MTTF): 2 million device

hours

– Static and dynamic wear leveling

– Uncorrectable bit error rate (UBER): <1 sector

per 10

bits read

• Endurance: Total bytes written (TBW)

– 100GB: 1.75PB; 200GB: 3.50PB; 400GB: 7.00PB

• Capacity

(unformatted): 100GB, 200GB, 400GB

• Mechanical: 7.0mm height

– SATA connector: 5V ±10%

– 2.5-inch drive: 100.5mm x 69.85mm x 7.0mm

• Field-upgradeable firmware

• Power consumption: <7.5W (TYP)

• Operating temperature

– Commercial (0°C to 70°C)

Notes:

1. Typical I/O performance numbers as meas-

ured using Iometer with a queue depth of

32 and write cache disabled.

2. 4KB transfers used for READ/WRITE latency

values.

3. The product achieves a MTTF based on pop-

ulation statistics not relevant to individual

units.

4. 1GB = 1 billion bytes; formatted capacity is

less.

5. Drive case temperature.

Warranty: Contact your Micron sales representative

for further information regarding the product,

including product warranties.

P400m 2.5-Inch NAND Flash SSD

Features

PDF: 09005aef84952553

p400m_2_5.pdf - Rev. G 5/13 EN

Micron Technology, Inc. reserves the right to change products or specifications without notice.

Products and specifications discussed herein are subject to change by Micron without notice.

Summary of content (29 pages)

PAGE 1
P400m 2.5-Inch NAND Flash SSD Features P400m 2.5-Inch SATA NAND Flash SSD MTFDDAK100MAN-1S1AA, MTFDDAK200MAN-1S1AA, MTFDDAK400MAN-1S1AA Features • • • • • • • • • • • • • • • Reliability – Mean time to failure (MTTF): 2 million device hours3 – Static and dynamic wear leveling – Uncorrectable bit error rate (UBER): <1 sector per 1016 bits read • Endurance: Total bytes written (TBW) – 100GB: 1.75PB; 200GB: 3.50PB; 400GB: 7.00PB • Capacity4 (unformatted): 100GB, 200GB, 400GB • Mechanical: 7.
PAGE 2
P400m 2.5-Inch NAND Flash SSD Features Part Numbering Information Micron’s P400m SSD is available in different configurations and densities. Visit micron.com for a list of valid part numbers. Figure 1: Part Number Chart MT FD D AK 100 M AN - 1 Micron Technology S 1 AA ES Production Status Product Family Blank = Production ES = Engineering sample Drive Interface Blank = Commercial (0°C to 70°C) FD = Flash drive Operating Temperature Range D = SATA 6.
PAGE 3
P400m 2.5-Inch NAND Flash SSD General Description General Description Micron’s P400m solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and n-channels of Micron NAND Flash internally. Packaged in an HDD replacement enclosure, the SSD integrates easily in existing storage infrastructures. The P400m SSD is designed to support and manage the needs of enterprise platforms that utilize significant read/write mixed workloads.
PAGE 4
P400m 2.5-Inch NAND Flash SSD Logical Block Address Configuration Logical Block Address Configuration The drive is set to report the number of logical block addresses (LBA) that will ensure sufficient storage space for the specified density. Standard LBA settings, based on the IDEMA standard (LBA1-02), are shown below.
PAGE 5
P400m 2.5-Inch NAND Flash SSD Interface Connectors Interface Connectors The SATA signal segment interface cable has four conductors and three ground connections. As shown in Package Dimensions, the cable includes a 7-pin signal segment and a 15-pin power segment arranged in a single row with a 1.27mm (0.050in) pitch.
PAGE 6
P400m 2.
PAGE 7
P400m 2.
PAGE 8
P400m 2.
PAGE 9
P400m 2.
PAGE 10
P400m 2.
PAGE 11
P400m 2.
PAGE 12
P400m 2.
PAGE 13
P400m 2.
PAGE 14
P400m 2.
PAGE 15
P400m 2.
PAGE 16
P400m 2.
PAGE 17
P400m 2.
PAGE 18
P400m 2.
PAGE 19
P400m 2.
PAGE 20
P400m 2.5-Inch NAND Flash SSD Device ID Table 5: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 222 Default Value Description – – – 15–12 – 0001b 11–6 – 000000b 5 – 1b Reserved SATA rev 3.0 4 – 1b Reserved SATA rev 2.6 3 – 1b Reserved SATA rev 2.5 2 – 1b Reserved SATA II: Extensions 1 – 1b Reserved SATA 1.
PAGE 21
P400m 2.
PAGE 22
P400m 2.
PAGE 23
P400m 2.5-Inch NAND Flash SSD Performance Performance Measured performance can vary for a number of reasons. The major factors affecting drive performance are the density of the drive and the interface of the host. Additionally, overall system performance can affect the measured drive performance. When comparing drives, it is recommended that all system variables are the same, and only the drive being tested varies. Performance numbers will vary depending on the host system configuration.
PAGE 24
P400m 2.5-Inch NAND Flash SSD Reliability Table 9: MTTF (Continued) MTTF (Operating Hours)1 Density Note: 200GB 2 million 400GB 2 million 1. The product achieves a MTTF of 2 million hours based on population statistics not relevant to individual units. Endurance Endurance for the SSD can be predicted based on the usage conditions applied to the device, the internal NAND component cycles, the write amplification factor, and the wear-leveling efficiency of the drive.
PAGE 25
P400m 2.5-Inch NAND Flash SSD Electrical Characteristics Electrical Characteristics Stresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
PAGE 26
P400m 2.
PAGE 27
P400m 2.5-Inch NAND Flash SSD Package Dimensions Package Dimensions Figure 4: 2.5-Inch Package – 7mm 13.43mm/0.529in for reference only +0.00 7.00mm -0.20 +0.000 0.276in -0.008 D&TM3 x 0.5mm (2 PLCS)(both sides) 14.00mm 0.551in (both sides) 3.50mm ±0.38 0.138in ±0.015 90.60mm 3.567in (both sides) 3.00mm 0.118in (2 PLCS) (both sides) 100.50mm/3.957in for reference only 0.30mm/0.012in for reference only D&TM3 x 0.5mm (4 PLCS) 4.07mm 0.160in 61.71mm 2.430in 69.85mm ±0.25 2.750in ±0.010 9.40mm 0.
PAGE 28
P400m 2.5-Inch NAND Flash SSD References References • Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available at www.sata-io.org • SATA 3.0 GOLD • ATA-8 Rev. 4 PDF: 09005aef84952553 p400m_2_5.pdf - Rev. G 5/13 EN 28 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved.
PAGE 29
P400m 2.5-Inch NAND Flash SSD Revision History Revision History Rev. G – 5/13 • Updated Compliance section Rev. F – 4/13 • Updated Compliance section Rev. E – 2/13 • Updated power consumption and operating shock numbers in Electrical Characteristics section Rev. D – 2/13 • Updated performance numbers in Features and Performance sections Rev.