Copyright CRT France 2014 Downloaded from www.cbradio.
and EN 62311.
CONTENTS FUNCTIONS & FEATURES.............................................................................................................................................................1 STANDARD ACCESSORIES...........................................................................................................................................................1 INSTALLATION.......................................................................................................................................
FUNCTIONS & FEATURES 1 1. Big LCD displays frequency and all kinds of information 2. PA、AM、FM、USB、LSB mode 3. Frequency Tuning Step can be 100Hz,1KHz,10KHz,100KHz,1MHz 4. ± 1.5KHz Clarifier 5. Flexiable menu function and PC programming software 6. ECHO Function 7. SQ, ASQ Function (FM and AM mode only) 8. RF GAIN Adjustment 9. RF PWR Adjustment 10.SCAN Function 11.Programmable RB Function 12.NB/ANL Function 13.DW DUAL-WATCH Function 14.BEEP Voice Prompt 15.+10KHZ Function 16.SWR、S/RF function 17.
INSTALLLATON Choose the most appropriate setting from a simple and practical point of view. Your radio should not interfere with the driver or crash the driver's knee or leg when rush brake. 1. Using the self-tapping screws and pads(2 sets) to fix the bracket. 2. Put the Non-slip mat on the 2 ends of the bracket and put in the radio.Then insert the adjusting screws and check carefull each screws, make sure the screws and machinme will not loose when the car shaking. 3.
Replacing Fuse This radio adopt 10A, 250V fuse. If the fuse blows, determine the reason, then correct the problem. After the problem is resolved, replace the fuse. If newly installed fuses continue to blow, disconnect the power cable and contact your autho-rized dealer or an authorized servicecenter 1. Pull the two fuse cover in difference direction and open it. 2. Replace the broke fuse with good one, and close the fuse holder. 3. Be sure to use suggested fuse, or it might damage the radio.
Rear Panel 20 19 18 LCD Display 1 ANT 5 7 6 9 8 11 10 12 13 15 14 17 16 18 EXT SP DATA 19 22 23 2 3 4 20 18 19 20 PC Cable Jack External Speaker Jack Antenna Jack Microphone 4 Channel Down Channel UP PTT Connector Mic Microphone cable 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 21 Appears when press MENU key. Appears when adjust SSB clarifier frequency. Appears when use ASQ. Appears during scan function. Indication of working mode. Appears when set with CTCSS code.
HOW TO USE YOUR RADIO OFF/ON Radio 1. Turn VOL clockwise to switch on the radio, the radio emit a beep. When the LCD displays frequency or channel, the radio is on. 2. Turn VOL anti-clockwise to switch off the radio, the radio is OFF. when hear Ka Ta from the switch. Volume Control When the radio is turned on, turn VOL clockwise will increase the volume, turn VOL anti-clockwise will reduce the volume. The LCD displays VOL: XX (XX stands for the volume level, total 1-36 levels).
2. Delete memory channel: In channel mode, hold【MEM】for over 2 seconds, the memory channel number flashes, turn the CH switch to choose the memory to be deleted. Then hold【MEM】until the flashing channel number disappear, the delete is done. 【MODE】 Short press【MODE】to choose mode FM-AM-USB-LSB-PA. 【BAND】 Short press【BAND】to choose band A-B-C-D-E-F-G-H-I. 【FRQ】 Short press【FRQ】to switch between frequency display mode and channel display mode. 6 【MENU】 1.
Split function.(REP menu 3 page 11) to transmit and receive on different frequencies with a shift (+ or-). To adjust the shift value between frequencies, see menu 11 page 14. 3 Offset Direction CHANNEL FUNCTION MENU OPERATION 7 1. Press【MENU】, the top left of LCD display "F", Press【PUSH】 to enter menu list. 2. Turn Channel switch to find No.1- No.5 menus. 3. Press【PUSH】to choose the menu. 4. Turn Channel switch to choose wanted value. 5.
PUBLIC DATA FUNCTION MENU OPERATION 1. 2. 3. 4. 5. No. 1 8 Hold【PUSH】for 2 seconds to enter menu list; Turn Channel switch to find menu No.1 to No.5; Press【PUSH】to choose the menu; Turn channel switch to choose wanted value. Press【PUSH】to return to previous menu, press any other key or wait 5 seconds, the setting will be stored and exit. Function Hi-cut LCD Display Values and Descriptions OFF: Shut HI-CUT function; ON: Open HI-CUT function; Default : OFF.
7 8 9 Voltage Protection Scan Type SQ: SQ scan function; TI: Time scan function; Default: SQ Clarifier OFF: Shut frequency adjustment R: Open RX frequency adjustment; T: Open TX frequency adjustment; RT: Open TX/RX frequency adjustment; Default: R 9 10 11 12 OFF: Shut voltage protection function; ON: Open voltage protection function; Default: ON Backight WHITE,BLUE,GREEEN, YELLOW, RED,PURPLE,CYAN Default: WHITE REP frequency Frequency Range: 100Hz-5MHz Default: 100KHZ Reset OPT: All functio
RECEIVER 10 Sensitivity SSB: 0.25μV for 10dB(S+N)/N AM:1.0μV for 10dB(S+N)/N FM: 1.0μV for 20 dB (S+N)/N (All at greater than 1/2 watt of audio output) Adjacent-Channel Selectivity AM/FM: 60dB Image Rejection More than 65dB IF Frequency AM/FM: 10.695MHz 1st IF, 455KHz 2nd IF SSB: 10.695MHz RF Gain Control 45dB adjustable for optimum signal reception Automatic Gain Control(AGC) Less than 10dB change in audio output for inputs from 10 to 100,000 microvolt.
EN 60950-1+A1+A11+A12 EN 301 489-1 EN 301 489-15 EN 301 783-1 EN301 783-2 EN 62311 Notified body PHOENIX TESTLAB Gmbh Germany Date 04/16/2014
CONDITIONS OF GUARANTEE Our transceivers CRT SUPERSTAR are guaranteed on 2 year. The other equipments: 6 months. Any abnormality of functioning must be indicated to your retailer, who will intervene or will send it to our technical service for control The spare parts of our devices are the object of no sending under guarantee Are excluded of the guarantee: - The damages caused by accidents, shocks, natural elements (lightning, thunderstorm, static electricity etc.
A1.
