TABLE OF CONTENTS AMPLIFIERS Installed Sound CTs 2-Channel Series ..................................... 6 CTs Multi-Channel Series ............................... 8 CTs Multi-Channel with CobraNet ................ 10 CDi Series .................................................... 12 DSi Series .................................................... 14 House of Worship with CDi.......................... 16 House of Worship with CTs ......................... 16 Multiple-Zone Sound System with CDi ........
INSTALLED SOUND INSTALLED SOUND CTs 2-Channel Series CTs Multi-Channel Series CTs Multi-Channel with CobraNetTM CDi Series DSi Series
AMPLIFIERS INSTALLED SOUND CTs Series: The New Standard CTs 600, CTs 1200, CTs 2000, CTs 3000 Foundation FEATURES • • • • • High power density. All two channel models in a 2U chassis. New Crown Switching Power Supply for lighter weight. Selectable “Constant-Voltage” or low-impedance operation per channel. 100V direct outputs on CTs 2000, CTs 3000. Fully PIP2-compatible.
SPECIFICATIONS Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.25 dB. Signal-to-Noise Ratio, A-weighted, below rated power (20 Hz to 20 kHz): 105 dB. Total Harmonic Distortion (THD) at full rated power, from 20 Hz to 20 kHz CTs 600 & CTs 1200: < 0.1%. CTs 2000 & CTs 3000: < 0.35%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from –40 dB to full power: < 0.1% for CTs 600/1200 and < 0.35% for CTs 2000/3000.
AMPLIFIERS INSTALLED SOUND CTs Multi-Channel Series: The New Standard CTs 4200, CTs 8200 Flexibility FEATURES • • • • • • High power density: Four-channel model in a 2U chassis, eight-channel model in a 3U chassis. New Crown Switching Power Supply for lighter weight. Selectable “Constant-Voltage” or low-impedance (4/8 ohm) operation per channel-pair. 100V direct outputs. New “FIT” (Fault Isolation Topology) circuitry isolates fault conditions without affecting neighboring channels.
SPECIFICATIONS Performance Frequency Response (at 1 watt, 20 Hz - 20 kHz): ±0.5 dB. Phase Response (at 1 watt, 10 Hz - 20 kHz): ±35°. Signal to Noise Ratio (below rated power, 20 Hz to 20 kHz): 100 dB unweighted. Total Harmonic Distortion (THD) at 1 watt, from 20 Hz to 20 kHz: < 0.05%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from 163 milliwatts to full bandwidth power: < 0.05% (typical). Damping Factor: 10 Hz to 400 Hz: >180. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB.
AMPLIFIERS INSTALLED SOUND CTs Multi-Channel Series: With CobraNet CTs 4200USP/CN, CTs 8200USP/CN TM CobraNet Capable FEATURES (input module) • • • • • • 100 Mbps Ethernet single-plug solution for CobraNet audio, and HiQnet™ control and monitoring. Analog audio inputs allow CobraNet network audio input, CobraNet audio backup, or a hardwire emergency override of CobraNet audio. 24 bit digital to analog conversion with 32 bit, floating point DSP processing. Firmware upgrades via the network.
SPECIFICATIONS USP/CN CobraNet Module Specifications (for amplifier specifications, see the CTs MultiChannel Series pages) Connectors: AUX Connector: Configurable for AUX input, AUX output and Listen Bus. Listen Bus is also supported through CobraNet. Network Connector: The dual RJ45 CobraNet connectors allow a Primary & Secondary connection to the 100Mb Ethernet network.
AMPLIFIERS INSTALLED SOUND CDi Series: 2/4/8 Ohm, 70V per channel CDi 1000, CDi 2000 Versatility FEATURES • • • • • • Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting. Computer connectivity via USB allows fast setup and configuration with HiQnet™. Barrier strip outputs, removable Phoenix-style input. Extremely versatile, handling a wide range of speaker impedances and outputs. Switch-mode universal power supply.
Output Power: See power charts on previous page. Output EQ: 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can NOT be bypassed. Filters are enabled individually. Voltage Gain at 1kHz, 8 ohm rated output: Delay: Up to 50 msec total delay per channel. SPECIFICATIONS Performance CDi 1000: 30.5 dB. CDi 2000: 32.9 dB. Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads.
AMPLIFIERS INSTALLED SOUND DSi Series: 2, 4, 8 ohm DSi 1000, DSi 2000, DSi 4000 One-touch Performance FEATURES • • • • Intuitive front-panel LCD screen, automatic presets for popular JBL speaker systems for quick, easy configuration. Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting. Computer connectivity via USB allows fast setup and configuration with HiQnet™. Barrier strip outputs, removable Phoenix-style input.
SPECIFICATIONS Performance Voltage Gain at 1kHz, 8 ohm rated output: DSi 1000: 26 dB. DSi 2000: 26 dB. DSi 4000: 26 dB. Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. Sensitivity: At 8 ohm rated output: DSi 1000: 2.35V. DSi 2000: 3.09V. DSi 4000: 3.61V. At 4 ohm rated output: DSi 1000: 2.24V. DSi 2000: 2.84V. DSi 4000: 3.47V. At 2 ohm rated output: DSi 1000: 1.88V.
INSTALLED SOUND Product Applications BSS FDS-336 Loudspeaker Management System dbx DriveRack 220V CDi 2000 dbx 480 Remote Unit for DriveRack 480
INSTALLED SOUND Product Applications Network Switch
www.crownaudio.
COMMERCIAL AUDIO Preamplifier-Mixers Amplifiers Mixer-Amplifiers XM Business Music Systems
COMMERCIAL AUDIO PREAMPLIFIER-MIXERS 14M, 28M Adaptable FEATURES • • • • • • • • 20 • www.crownaudio.com 4 or 8 inputs, 1 or 2 output channels. Ideal for commercial and industrial use. Balanced Phoenix-type mic/line inputs; RCA inputs. Balanced Phoenix-type line outputs. Any input can be sent to any output. Built-in tone generator. Priority muting. Independent bass and treble controls for each input.
SPECIFICATIONS Performance Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB. Signal to Noise Ratio (master volume at minimum): 100 dB. THD: 0.05% typical with 800 mV balanced input, 1V output. Input Sensitivity (volts RMS for full output at maximum gain): Tone Controls: Bass and Treble non-detented potentiometers on each input channel. Bass ±10 dB at 100 Hz, Treble ±10 dB at 10 kHz. Power Indicator: Blue LED indicates power on.
COMMERCIAL AUDIO AMPLIFIERS 180A, 280A, 1160A Power Zone FEATURES • • • • Ideal for commercial and industrial use. Balanced Phoenix-type line inputs; touch-proofed screw-terminal speaker outputs. Advanced protection system includes output current limiting, DC protection, circuit breaker/fuse, and thermal protection. 1 or 2 inputs; 1 to 2 amplifier output channels.
SPECIFICATIONS Performance Frequency Response (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz +/- 1 dB. Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB. Power Bandwidth (at 4-ohm tap, 2 dB below maximum 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB. DC Output Offset: < ±5 mV. THD: Less than 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain): 800 mV. Input Impedance (nominal): 100 kilohms.
COMMERCIAL AUDIO AMPLIFIERS 660A 6-Channel FEATURES • • • • 6 inputs; 6 amplifier output channels. Balanced Phoenix-type line inputs; touch-proof screw-terminal speaker outputs. Advanced protection system includes output current limiting, DC protection, circuit breaker/fuse, and thermal protection. Ideal for commercial and industrial use. POWER OUTPUT* Model 4-ohm 70V/100V Inputs System Zones 660A 60W 60W 6 Six-zone *Minimum guaranteed power in watts at 1 kHz with 0.5% THD. 24 • www.
Power Indicator: Blue LED indicates power on. DC-Fault Load Protection: Included. Included Accessories Frequency Response (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz ±1 dB. Output Signal Presence Indicator: Green LED, one for each output channel, illuminates when output signal level exceeds 100 mV (45 dB below full power) from the 4-ohm tap. Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB. Clip Indicators: Red LED, one per output channel. Illuminates at threshold of audible distortion.
COMMERCIAL AUDIO MIXER-AMPLIFIERS 180MA, 280MA, 1160MA Practical FEATURES • • • • • • 4 to 8 inputs, 1 to 2 amplifier output channels. Ideal for commercial and industrial use. Balanced Phoenix-type mic/line inputs; touch-proofed screw-terminal speaker outputs. Any input can be sent to any output. Priority muting. Built-in four-tone generator.
SPECIFICATIONS Performance Frequency Response: 30 Hz to 15 kHz ±1 dB at line out. Power Bandwidth: 50 Hz to 20 kHz with < 0.5% THD at 2 dB below maximum 1 kHz power. Signal to Noise Ratio: 85 dB, master volume at minimum. DC Output Offset: < ±5 mV. THD: Less than 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain): Balanced mic inputs: 3 mV. Balanced line inputs: 800 mV. RCA connectors: 400 mV. Input Impedance: Mic: 400 ohms. Line: 100 k ohms. RCA: 50 k ohms.
COMMERCIAL AUDIO MIXER-AMPLIFIERS 140MPA Music & Paging FEATURES • • • • • 4 inputs (each with a volume control), one 40W amplifier output channel. Ideal for paging, background music, and music-on-hold. Balanced Phoenix-type mic/line inputs, telephone input, dual RCA stereo music inputs, touch-proof screw-terminal speaker outputs. Priority ducking. Independent bass and treble controls for each input.
SPECIFICATIONS Performance Frequency Response (at 1 watt from 4-ohm tap): 50 Hz to 15 kHz ± 1 dB. Frequency Response (at line out): 50 Hz to 15 kHz ± 1 dB. Power Bandwidth (at 4-ohm tap, 2 dB below maximum 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD. Signal to Noise Ratio (ref. to rated power, master volume at minimum): >90 dB. DC Output Offset: < ±5 mV. THD: < 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain): Balanced mic inputs: 3 mV. Balanced line inputs: 800 mV.
COMMERCIAL AUDIO XM TUNER-MIXER-AMPLIFIERS 180MAx Pack (180MAx tuner-mixer-amplifier also available separately) XM Enabled FEATURES • • • • • Programmable XM tuner with XM channel data display. Independent bass and treble controls for each input. Balanced Phoenix-type mic/line inputs; touch-proof screwterminal speaker outputs. Priority ducking, Music-On-Hold (MOH) outputs. 180 MAx Pack includes four JBL Control 1ST 2-way speakers with 70V transformer and mounting brackets, remote control and XM antenna.
SPECIFICATIONS Performance Frequency Response (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz ±1 dB. Frequency Response (at line out): 20 Hz to 20 kHz ±1 dB. Power Bandwidth (at 4-ohm tap, 2 dB below maximum 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB. Input Signal Presence Indicator: Green LED illuminates when input signal exceeds –24 dBu (line) or –70 dBu (mic).
COMMERCIAL AUDIO Product Applications Small Pub Using 180MAx PACK XM Antenna AKG D 524 E Microphone Crown 180MAx Cable TV Box JBL Control 1ST CD/DVD Player Crown 1-VCAP Wall Volume Control Small Restaurant Zone 1 Harman Kardon DVD-31 Player JBL Control 25T Crown 280MA Mixer-Amplifier Harman Kardon FL 8385 CD Player Satellite Receiver Zone 2 JBL Control 28T-60 Crown 1-VCAPs Zone 1 AKG D 524 ST-S Microphone Zone 2
COMMERCIAL AUDIO Product Applications Medium Retail Store Crown 28M Mixer JBL Control 24CT Music Service Crown 660A Power Amplifier JBL Control 24CT Harman Kardon FL 8385 CD Player JBL Control 19CS Satellite Receiver JBL Control 25AV 1-VCAP AKG D 524 ST-S Microphone Branded Apparel Store JBL Control 24CT (Ceiling Mount) JBL Control 26CT (Ceiling Mount) Restrooms - Hallways Crown 14M Mixer AKG D 524 E Microphone Music Service Crown CTs 8200 Power Amplifier CD Player JBL Control 19CS Subwoofers
www.crownaudio.
PORTABLE PA XTi Series XLS Series
AMPLIFIERS PORTABLE PA XTi Series: World-Class XTi 1000, XTi 2000, XTi 4000 World-Class FEATURES • • • • • • • • Computer connectivity via USB allows fast setup and configuration with HiQnet™. Integrated speaker presets with LCD front panel display. Extremely versatile, handling a wide range of speaker impedances and outputs. Switch-mode universal power supply. Speaker presets for crossover frequencies, EQ, limiting, and delay.
SPECIFICATIONS Performance Voltage Gain at 1kHz, 8 ohm rated output: XTi 1000: 30.5 dB. XTi 2000: 32.9 dB. XTi 4000: 34.2 dB. Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Delay: For signal alignment of driver; 50 mS total delay. Subharmonic Synthesizer: Takes the low-frequency content of the input signal and “synthesizes” a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect.
AMPLIFIERS PORTABLE PA XLS Series: Affordable and Reliable XLS 202, XLS 402, XLS 602, XLS 802 Evolution FEATURES • • • • Housed in a rugged, all-steel 2U chassis. Efficient forced-air fan prevents excessive thermal buildup. Electronically balanced XLR inputs; touchproof binding post and Speakon outputs. Precision detented level controls, power switch, and four LEDs, which indicate clip for each channel, power and fault conditions.
SPECIFICATIONS Performance Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25 V. Frequency Response (at 1 watt) 22 Hz to 20 kHz: +0 dB, –1 dB. Signal-to-Noise Ratio (20 Hz to 20 kHz, inputs terminated) A-weighted, below rated power: > 100 dB. No weighting, below rated power: > 95 dB. Total Harmonic Distortion (THD): < 0.5%. Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%. Circuit Breaker: Back-panel breaker provides overload protection.
AMPLIFIERS PORTABLE PA Product Applications Musician or DJ with Dual Subwoofers Musician or DJ Suggested for Medium Venues XTi 1000 XTi 4000
AMPLIFIERS PORTABLE PA Product Applications DJ Suggested for Large Venues XTi 1000 XTi 4000 Regional Tour Suggested for Large Venues XTi 1000 XTi 4000 XTi 2000 (Bridge mode) XTi 2000 (Bridge mode) XTi 4000 XTi 4000
www.crownaudio.
TOURING I-Tech Series MA-VZ Series Macro-Tech 2402
AMPLIFIERS TOURING I-Tech Series: Excellence Without Compromise I-T4000, I-T6000, I-T8000 Excellence FEATURES • • • • • Unmatched power in a 2U lightweight chassis. Global power supply with Power Factor Correction. Onboard DSP. Connects to Harman Pro HiQnet and Crown TCP/ IQ™ network (CobraNet input available in optional CN models, coming soon). LCD control screen allows easy setup, diagnostics, and DSP presets for various loudspeakers.
SPECIFICATIONS Performance Frequency Response (at 1 watt, 20 Hz - 20 kHz): ±0.25dB. Signal to Noise Ratio (below rated full-bandwidth power, A-weighted): > 105 dB. Total Harmonic Distortion (THD) at full rated power: < 0.35%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to –35 dB: < 0.35%. Damping Factor (20 Hz to 100 Hz, 8 ohms): > 5000. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB. Common Mode Rejection (CMR) (20 Hz to 1 kHz): > 50 dB.
AMPLIFIERS TOURING Macro-Tech VZ® Series: Advanced VZ Technology Macro-Tech 3600VZ, Macro-Tech 5002VZ VZ Technology FEATURES • • • • • Crown’s Grounded Bridge™ design provides lower distortion and superior reliability. Patented ODEP® (Output Device Emulation Protection) circuitry compensates for overheating and overload to keep the amplifier working when others would fail. Articulated VZ® power supplies for each channel provide excellent crosstalk characteristics and the best power matching to your load.
SPECIFICATIONS Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (at 1 watt, 10 Hz to 20 kHz): ±10 degrees. Signal-to-Noise Ratio (below rated full bandwidth power), A-weighted: > 105 dB. Total Harmonic Distortion (THD) (at rated power): Front Panel Controls and Indicators Level: Rotary detented level control, one for each channel. Compressor (MA-5002VZ only): Controls the channel’s error-driven compression.
AMPLIFIERS TOURING Macro-Tech 2402: Advanced Reinforcement Macro-Tech 2402 Advanced FEATURES • • • • Enhanced PIP2™ (Programmable Input Processor) connector accepts new accessory modules that tailor the amplifier for specific applications. Balanced XLR and 1/4-inch phone jacks for each channel on the standard PIP-FXQ module.
SPECIFICATIONS Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (at 1 watt, 10 Hz to 20 kHz): ±10 degrees. Signal-to-Noise Ratio (below rated full bandwidth power), A-weighted: > 105 dB. Total Harmonic Distortion (THD) (at rated power), 20 Hz to 1 kHz: < 0.05%. At 20 kHz: < 0.1%. Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1) from 163 milliwatts to full bandwidth power: < 0.05%. Damping Factor (8 ohm) 10 Hz to 400 Hz: >1000.
AMPLIFIERS TOURING Product Applications Small System
AMPLIFIERS TOURING Product Applications
www.crownaudio.
RECORDING & BROADCAST D Series
AMPLIFIERS RECORDING & BROADCAST D Series: Long-Term Favorites D-45, D-75A Tried & True FEATURES • • • • • • Powerful AB+B class circuitry yields maximum efficiency with minimum crossover “notch” distortion. IOC® (Input/Output Comparator) alerts of any distortion that exceeds 0.05% to provide proof of distortion-free performance. Ultra-low harmonic and intermodulation distortion result in the best dynamic transfer function in the industry.
SPECIFICATIONS Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (from 20 Hz to 20 kHz at 1 watt): +10 to –15 degrees. Signal-to-Noise Ratio below rated power (20 Hz - 20 kHz): 106 dB. Total Harmonic Distortion (THD) at full bandwidth power: 0.05% from 20 Hz to 20 kHz. Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1) from 0.25 watts to full bandwidth power: < 0.01%. from 0.01 to 0.25 watts: < 0.05%. Damping Factor, from DC to 400 Hz: > 400.
www.crownaudio.
CINEMA DSi Series CTs 2-Channel Series CTs Multi-Channel Series XLS Series DBC® Network Bridge
AMPLIFIERS CINEMA DSi Series: 2/4/8 Ohm DSi 1000, DSi 2000, DSi 4000 One-Touch Performance FEATURES • • • • • Intuitive front-panel LCD screen, automatic presets for popular JBL cinema speaker systems for quick, easy configuration. Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting. Computer connectivity via USB allows fast setup and configuration with HiQnet™ System Architect™ software.
SPECIFICATIONS Performance Frequency Response: +0/–1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. Sensitivity: At 8 ohm rated output: DSi 1000: 2.35V. DSi 2000: 3.09V. DSi 4000: 3.61V. At 4 ohm rated output: DSi 1000: 2.24V. DSi 2000: 2.84V. DSi 4000: 3.47V. At 2 ohm rated output: DSi 1000: 1.88V. DSi 2000: 2.24V. DSi 4000: 2.84V.
AMPLIFIERS CINEMA DSi-8M: Convenient Monitoring DSi-8M Performance Monitor FEATURES • • • • • • 60 • www.crownaudio.com Compact 2-rack unit. 8 channels for monitoring processor or amplifier inputs. All inputs and outputs are balanced to interface with new cinema processors. No level jumps when switching between processor and amplifiers. 25-pin D-sub connectors, plus removable terminal blocks and HD-15 for quick, hassle-free connections.
SPECIFICATIONS Performance Input Impedance (processor inputs): 10 kilohms. Input Impedance (power amplifier inputs): > 50 kilohms. Power Requirements: 100-240VAC, 50-60 Hz, 32 watts. Front Panel Controls and Indicators Channel Select Buttons and LEDs: Eight pushbutton switches, one for each input channel. Pressing a button monitors the signal from that channel, and lights the corresponding LED. Any combination of eight channels can be selected.
AMPLIFIERS CINEMA Other Cinema Products CTs 2-Channel FEATURES • • High power density. All two channel models in a 2U chassis. New Crown Switching Power Supply for lighter weight. • Selectable “Constant-Voltage” or low-impedance operation per channel. 100V direct outputs on CTs 2000, CTs 3000. Fully PIP2™-compatible.
CINEMA DBC NETWORK BRIDGE Other Cinema Products ® DBC Network Bridge FEATURES All-Digital Cinema Solution B-ChainTM A DBC® t the heart of a Digital system, the Crown Network Bridge allows you to distribute multiple channels of digital audio over standard fast Ethernet hardware and cabling for use in traditional, e-cinema and d-cinema applications.
AMPLIFIERS CINEMA Product Applications
AMPLIFIERS CINEMA Product Applications
www.crownaudio.
NETWORKED PRODUCTS HiQnet™ Software IQ® Software PIPs Accessories
NETWORKED PRODUCTS HARMAN PRO HiQnet SOFTWARE arman Pro System Architect is a fully-featured HiQnet™ software application that provides a seamless, easy-to-use interface for all the devices in the signal path—from microphones to speakers. Built using a modular software design, H System Architect takes full advantage of the knowledge and expertise of each audio company within the Harman Pro group.
amplifier loads, signal routes and processing, are also easily monitored from a single control station. And when it's time to reconfigure, System Architect can quickly update device routing and settings, amplifier configurations and speaker tunings. User control and configuration also reaches new levels with System Architect. The intuitive software interface provides easy customization of window sets and control-panel design, as well as a full-screen-mode option, for user touchscreen PC control.
INETWORKED PRODUCTS PIPS TCP / IQ ANALOG AUDIO INPUTS PIP LITE PIP USP3 SmartAmp Automation for Networked Audio Digital Signal Processing for Networked Audio he Crown PIP LITE is a PIP (Programmable Input Processor) input module for PIP2 compatible amplifiers. The PIP-LITE connects to an audio control network via 100 Mb Ethernet. The audio path in the PIP LITE is processed totally in the analog domain.
PIP USP3/CN SmartAmp Automation for TCP/IQ he Crown PIP-USP3/CN is a 3rd generation DSP-based PIP™ (Programmable Input Processor) input module for PIP2 compatible amplifiers.* It connects the amplifier to a 100 Mb Ethernet network allowing it to be remotely controlled and monitored. In addition, the USP3/CN allows the transport of real-time digital audio via CobraNet over the same Ethernet network.
www.crownaudio.
ACCESSORIES & REFERENCE Accessories Amplifier Feature Comparison Amplifier Specifications Module Compatibility Crown Amplifier Warranty
ACCESSORIES & REFERENCE ACCESSORIES Accessories P.I.P.-CLP Is designed to detect and prevent overload. The same error detecting circuit that is used to signal the IOC indicator is used to activate this error-driven compressor. It is not a typical signal-driven compressor but a circuit to prevent an overload. It can yield up to 13 dB of additional signal safety margin without noticeable program change.
ACCESSORIES & REFERENCE AMPLIFIER FEATURE COMPARISON CHART Amplifier Feature Comparison MA3600VZ, MA5002VZ CTs 2-Ch. CTs multich. CTs multi CobraNet X 600/1200 only X X X X X X X X D XLS Xs I-Tech Dsi CDi XTi 2402 X X X X X X X X X X X 180A, 280A Protection systems ODEP/JTS Thermal Level Control (TLC) Automatic high-pass filter Switchable high-pass filter Low-pass filter (ultrasonic/RFI protect.
REFERENCE AMPLIFIER SPECIFICATIONS Amplifier Specifications Amplifiers 76 • Dual Power Per Channel1 Mono Power2 Dimensions Weight Comments CCA 180A 80W-4: 19 x 4.1 x 13.9" 21 lb 1 input, 1 output ch. CCA 280A 80W-4: or 70V/100V 19 x 4.1 x 13.9" 25.3 lb 2 inputs, 2 output ch. CCA 1160A 160W-4: or 70V/100V 19 x 4.1 x 13.9" 25.3 lb 1 input, 1 output ch. CCA 660A 60W-4: or 70V/100V 19 x 4.1 x 13.9" 30.3 lb 6 input ch., 6 output ch.
REFERENCE MODULE COMPATIBILITY Amplifier Specifications 1. 2. XLS 202 300W-4:, 200W-8: 600W-8: 19 x 3.5 x 15.2" 23 lb XLS 402 450W-4:, 300W-8: 900W-8: 19 x 3.5 x 15.2" 25.7 lb XLS 602 600W-4:, 380W-8: 1200W-8: 19 x 3.5 x 15.2" 29 lb XLS 802 800W-4:, 500W-8: 1600W-8: 19 x 3.5 x 15.2" 35.5 lb Xs500 750W-2:, 500W-4:, 400W-8: 1600W-4:, 1450W-8: 19 x 3.5 x 17" 28 lb Xs700 900W-2:, 750W-4:, 450W-8: 1900W-4:, 1645W-8: 19 x 3.
Crown Amplifier Warranty USA AND CANADA SUMMARY OF WARRANTY Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A. warrants to you, the ORIGINAL PURCHASER and ANY SUBSEQUENT OWNER of each NEW Crown product, for a period of three (3) years from the date of purchase by the original purchaser (the “warranty period”) that the new Crown product is free of defects in materials and workmanship.
Crown Amplifier Warranty WORLDWIDE EXCEPT USA & CANADA SUMMARY OF WARRANTY Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A.
