2005 Catalog Crown Amplifiers
TABLE OF CONTENTS AMPLIFIERS Installed Sound CTs 2-Channel Series......................................4 CTs Multi-Channel Series................................6 CH Series........................................................8 CL Series ......................................................10 CP660...........................................................12 Crown Commercial Audio Series ..................14 House of Worship with CL............................16 House of Worship with IQ and CTs..........
INSTALLED SOUND CTs 2-Channel Series CTs Multi-Channel Series CH Series CL Series CP660 Crown Commercial Audio Series
AMPLIFIERS `INSTALLED SOUND CTs Series: The New Standard CTs 600, CTs 1200, CTs 2000, CTs 3000 Foundation `FEATURES • High power density. All two channel models in a 2U chassis. • New Crown Switching Power Supply for lighter weight. • Selectable “Constant-Voltage” or low-impedance operation per channel. • 100V direct outputs on CTs 2000, CTs 3000. • Fully PIP2-compatible.
`SPECIFICATIONS Controls and Indicators Construction Performance Front Panel Indicators: Bridge Mode, Ready, Signal, Clip, Thermal, Fault, Data, Power. Ventilation: Front-to-rear forced airflow. Two continuously variable speed fans direct the airflow through the amplifier for cooling. Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.25 dB. Signal-to-Noise Ratio, A-weighted, below rated power (20 Hz to 20 kHz): < 105 dB.
AMPLIFIERS `INSTALLED SOUND CTs Multi-Channel Series: The New Standard CTs 4200, CTs 8200 Flexibility `FEATURES • High power density: Four-channel model in a 2U chassis, eight-channel model in a 3U chassis. • New Crown Switching Power Supply for lighter weight. • Selectable “Constant-Voltage” or low-impedance (4/8 ohm) operation per channel-pair. • 100V direct outputs. • New “FIT” (Fault Isolation Topology) circuitry isolates fault conditions without affecting neighboring channels.
`SPECIFICATIONS Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.5 dB. Phase Response (at 1 watt): 10 Hz to 20 kHz: ±35°. Signal-to-Noise Ratio, unweighted, below rated power (20 Hz to 20 kHz): 100 dB. Total Harmonic Distortion (THD) at full rated power, from 20 Hz to 20 kHz: < 0.1%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from 163 milliwatts to full bandwidth power: < 0.05% (typical). Damping Factor, 10 Hz to 400 Hz: > 180.
AMPLIFIERS `INSTALLED SOUND CH Series: 4/8 Ohm, 70V or 100V per channel CH1, CH2, CH4 Versatility `FEATURES • Drives multiple impedances, with both low impedance and high impedance outputs per channel. • High-pass filter for each channel provides low-frequency roll off to eliminate step down transformer saturation when used in 70V distributed systems. • Rear panel detented level controls allow for accurate level settings and secure operation.
`SPECIFICATIONS Power Load Impedance: Safe with all types of loads. Common Mode Rejection (CMR): Better than 40 dB from 20 Hz to 1 kHz. DC Output Offset (Shorted Input): ±10 mV. CH1: 4 and 8 ohm Stereo; 16 ohm at 70V Stereo; 32 ohm at 100V Stereo; 8 and 16 ohm Bridge; 32 ohm at 140V Bridge; 64 ohm at 200V Bridge. Controls CH2: 4 and 8 ohm Stereo; 8 ohm at 70V Stereo; 16 ohm at 100V Stereo; 8 and 16 ohm Bridge; 16 ohm at 140V Bridge; 32 ohm at 200V Bridge.
AMPLIFIERS `INSTALLED SOUND CL Series: High-Power, 2 Ohm Operation CL1, CL2, CL4 Powerful `FEATURES • Low impedance compatibility for applications where high power, low impedance loads are the primary requirement. • Rear panel detented level controls allow for accurate level settings and secure operation. • “Contractor Correct” barrier strip output connectors allow for quick and easy connection, regardless of the load.
`SPECIFICATIONS Controls Protection Power Level: A detented rotary level control for each channel located on the rear panel. Protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature, chain destruction phenomena, input overload damage and high-frequency blowups. They also protect loudspeakers from input/output DC, large or dangerous DC offsets and turn-on/turn-off transients. Load Impedance: Safe with all types of loads.
AMPLIFIERS `INSTALLED SOUND CP Series: 6-Channel Flexibility CP660 6 Channel `FEATURES • Six independent amplifier channels and three bridging switches provide maximum configuration flexibility. • Separate gain controls on the back panel allow convenient level balancing of all channels. • Super-quiet variable-speed fan with auto trigger provides silent, efficient cooling. • Three Dual/Mono switches on the back panel give a broad range of flexibility in configuring your system.
`SPECIFICATIONS Back Panel Controls Dimensions Performance Level control for each channel; three two-position Dual/Mono switches (Ch. 1&2, Ch. 3&4, Ch. 5&6). AC line connector, EMA 5-15P (15A) on North American units. EIA Standard 19-inch rack mount width (EIA RS310-B), 3.5-inch (8.9-cm) height and 12.75-inch (32.3-cm) depth behind front mounting surface. Center of gravity is 6 inches (15.2 cm) behind the front mounting surface and 7 inches (17.8 cm) in from the outer edge of the left rack ear.
AMPLIFIERS `INSTALLED SOUND CCA Series: Crown’s Commerial Audio Series 180MA, 280MA, 1160MA Commercial Audio `FEATURES • 4 to 8 inputs, 1 to 2 amplifier output channels. • Ideal for commercial and industrial use. • Balanced Phoenix-type mic/line inputs; touch-proofed screw-terminal speaker outputs. • Any input can be sent to any output. • Built-in four-tone generator. • Priority muting.
`SPECIFICATIONS Performance Frequency Response: 30 Hz to 15 kHz ±1 dB at line out. Clip Indicators: Red LED, one per output channel. Illuminates at threshold of audible distortion. Tone Level: One per channel, a rear-panel potentiometer that sets the volume of the tones. Output Volume Controls: One per output channel. Detented pot with knob. Input Connectors:Mic/Line Connector, 3-pin Phoenix-type, low-impedance balanced, one per input channel.
AMPLIFIERS `INSTALLED SOUND Product Applications
AMPLIFIERS `INSTALLED SOUND Product Applications
PORTABLE PA Xs Series CE Series XLS Series
AMPLIFIERS `PORTABLE PA Xs Series: Power in Xs Xs500, Xs700, Xs900, Xs1200, Xs4300 Power in Xs `FEATURES • Housed in a rugged, all-steel 2U chassis. • Efficient forced-air fan prevents excessive thermal buildup. • 2-channel models have XLR-1/4-inch combo and Phoenix-style input connectors, daisy-chain XLR outputs, touch-proof binding post outputs and Speakon outputs.
`SPECIFICATIONS Front Panel Controls Performance Level: Two or four front-panel, gray rotary level controls, one for each channel. Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V. Frequency Response (at 1 watt) 22 Hz to 22 kHz: ±1 dB. Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5°, –18° Signal-to-Noise Ratio: A-weighted, below rated power: > 102 dB. 22Hz to 22kHz, below rated power: > 97 dB. Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 20 kHz: <0.5%.
AMPLIFIERS `PORTABLE PA CE Series: Power and Reliability CE 1000, CE 2000, CE 4000 2 Ohm Performance `FEATURES • Handles 2-ohm loads. • Front-panel detented level controls. • Function indicators, fan-assisted cooling, short-circuit protection. • Class “I” (BCA) circuitry in CE 4000 offers extra power and efficiency. • Selectable highpass and lowpass filters in CE 4000. • Works with SST modules that provide extra functions.
`SPECIFICATIONS Performance Power Draw At Idle: CE1000/2000: 90 watts; CE4000: 120 watts. CE 4000: 5-way plus Speakon. Other Connectors Frequency Response (at 1 watt): CE 1000/2000: ±0.2 dB from 20 Hz to 25 kHz. CE 4000: ±0.25 dB from 20 Hz to 20 kHz. Front Panel Controls Phase Response (at 1 watt) 20 Hz to 20 kHz: ±15 degrees. Level: A detented rotary level control for each channel. Signal to Noise Ratio (below rated power), 20 Hz to 20 kHz: CE 1000/2000: > 100 dB. CE 4000: > 102 dB.
AMPLIFIERS `PORTABLE PA XLS Series: Affordable and Reliable XLS 202, XLS 402, XLS 602 Evolution `FEATURES • Housed in a rugged, all-steel 2U chassis. • Efficient forced-air fan prevents excessive thermal buildup. • Electronically balanced XLR inputs; touchproof binding post and Speakon outputs. • Precision detented level controls, power switch, and four LEDs, which indicate clip for each channel, power and fault conditions.
`SPECIFICATIONS Protection Performance Front Panel Controls Sensitivity (volts RMS) for full rated power at 4 ohms, XLS 202: 0.725 XLS 402: 1.025 XLS 602: 1.26. Level: Two front-panel, black rotary level controls, one for each channel. Frequency Response (at 1 watt) 22 Hz to 20 kHz: ±0.75 dB. Back Panel Controls Power: Front-panel switch; on when in the UP position. Cooling Circuit Breaker: Provides overload protection. Phase Response (degrees at 1 watt) at 10 Hz: –10. at 20 kHz: +19.
AMPLIFIERS `PORTABLE PA Product Applications
AMPLIFIERS `PORTABLE PA Product Applications
TOURING I-Tech Series MA-VZ Series MA-02 Series
AMPLIFIERS `TOURING I-Tech Series: Excellence Without Compromise I-T4000, I-T6000, I-T8000 Excellence `FEATURES • Unmatched power in a 2U lightweight chassis. • Global power supply with Power Factor Correction. • Onboard DSP. • Connects to Harman Pro HiQnet and Crown TCP/IQ™ network (CobraNet input available in optional CN models, coming soon). • LCD control screen allows easy setup, diagnostics, and DSP presets for various loudspeakers.
`SPECIFICATIONS Frequency Response (at 1 watt, 20 Hz - 20 kHz): ±0.25dB. Signal to Noise Ratio below rated full-bandwidth power, A-weighted: > 105 dB Total Harmonic Distortion (THD) at full rated power: < 0.35%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to –35 dB: < 0.35%. Damping Factor (20 Hz to 100 Hz, 8 ohms): > 5000. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB. Common Mode Rejection (CMR) (20 Hz to 1 kHz): > 50 dB.
AMPLIFIERS `TOURING Macro-Tech VZ® Series: Advanced VZ Technology Macro-Tech 3600VZ, Macro-Tech 5002VZ VZ Technology `FEATURES • Crown’s Grounded Bridge design provides lower distortion and superior reliability. • Patented ODEP (Output Device Emulation Protection) circuitry compensates for overheating and overload to keep the amplifier working when others would fail. • Articulated VZ power supplies for each channel provide excellent crosstalk characteristics and the best power matching to your load.
`SPECIFICATIONS Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (at 1 watt, 10 Hz to 20 kHz): ±10 degrees. Signal-to-Noise Ratio (below rated full bandwidth power), A-weighted: > 105 dB. Total Harmonic Distortion (THD) (at rated power): MA-3600VZ: 20 Hz to 1 kHz: < 0.05%. 20 kHz: < 0.1%. MA-5000VZ: < 0.05% true THD Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1): MA-3600VZ (from 368 milliwatts to full rated output): < 0.05%.
AMPLIFIERS `TOURING Macro-Tech 02 Series: Advanced Reinforcement Macro-Tech 602, Macro-Tech 1202, Macro-Tech 2402, Advanced `FEATURES • Enhanced PIP2™ (Programmable Input Processor) connector accepts new accessory modules that tailor the amplifier for specific applications. • Balanced XLR and 1/4-inch phone jacks for each channel on the standard PIP-FXQ module.
`SPECIFICATIONS Back Panel Controls Protection Performance Stereo/Mono: A three-position back panel switch used to select Stereo, Bridge-Mono or ParallelMono mode. Macro-Tech amplifiers are protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature, chain destruction phenomena, input overload damage and high-frequency blowups. They also protect loudspeakers from input/output DC and turn-on/turn-off transients.
AMPLIFIERS `TOURING Product Applications
AMPLIFIERS `TOURING Product Applications
RECORDING & BROADCAST Studio Reference Series K Series D Series
AMPLIFIERS ` RECORDING & BROADCAST Studio Reference Series: The Industry Reference Studio Reference I, Studio Reference II Benchmark `FEATURES • Super-low harmonic and intermodulation distortion provide the best transfer function in the business. • Ultra-high damping factor delivers superior loudspeaker motion control for the cleanest, tightest, chest-thumping bottom end you’ve ever felt—or heard. • Extremely wide dynamic range.
`SPECIFICATIONS Front Panel Controls Output Connectors Performance Enable: Push button used to turn the amplifier on and off. Two sets of color-coded, 5-way binding posts accept banana plugs, spade lugs or bare wire. (European models do not accept banana plugs.) Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (at 1 watt, 20 Hz to 20 kHz): +5 to –15 degrees. Level: 31-detent, rotary level control, one for each channel. Meter On/Off: Turns the meters on or off.
AMPLIFIERS ` RECORDING & BROADCAST K Series: Radically Different K1, K2 Performance `FEATURES • Sealed chassis—no fan, no noise! • Patented Class “I” (BCA) circuit design. • Unmatched thermal efficiency; superior energy efficiency. • TLC -Thermal Level Control protection subtly and dynamically reduces gain as needed. • Significantly less component degrading heat generated.
`SPECIFICATIONS Performance Frequency Response: ± 0.25 dB from 20 Hz to 20 kHz. The frequency response is band limited with an 8 Hz double integrated 3rd-order Butterworth high-pass filter and a 32 kHz 7th-order Gaussian low-pass filter. Signal to Noise Ratio (Unweighted): >100 dB below rated power. Voltage Gain (at maximum level setting): 31.5 dB (K1) or 33.1 dB (K2) with input sensitivity set to 1.4V. 26 dB with input sensitivity set to 26 dB.
AMPLIFIERS ` RECORDING & BROADCAST D Series: Long-Term Favorites D-45, D-75A Tried & True `FEATURES • Powerful AB+B class circuitry yields maximum efficiency with minumum crossover “notch” distortion. • IOC® (Input/Output Comparator) alerts of any distortion that exceeds 0.05% to provide proof of distortion-free performance. • Ultra-low harmonic and intermodulation distortion result in the best dynamic transfer function in the industry.
`SPECIFICATIONS Front Panel Controls Construction Performance Power: A two-position rotary on/off switch. Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Level: An independent detented front-panel level control for each channel. Phase Response (from 20 Hz to 20 kHz at 1 watt): +10 to –15 degrees. Dual/Mono: A jumper located inside the amplifier selects between dual and mono operation. Durable black finish on aluminum front panel with gray suede Lexan insert.
CINEMA CTs 2-Channel Series CTs Multi-Channel Series CL Series CE Series XLS Series DBC Network Bridge
CTs 2-Channel AMPLIFIERS ` CINEMA CTs Series `FEATURES • High power density. All two channel models in a 2U chassis. • New Crown Switching Power Supply for lighter weight. • Selectable “Constant-Voltage” or low-impedance operation per channel. • 100V direct outputs on CTs 2000, CTs 3000. • Fully PIP2-compatible.
CL Series AMPLIFIERS ` CINEMA CL, CE and XLS Series `FEATURES POWER OUTPUT* 2-ohm Dual 4-ohm Dual Model (per channel) (per channel) CL1 CL2 CL4 560W 450W 975W 660W 1,400W** 1,200W • Low impedance compatibility for applications where high power, low impedance loads are the primary requirement. 4-ohm Bridge 1,100W 1,950W 2,800W** • Rear panel detented level controls allow for accurate level settings and secure operation.
CINEMA `DBC NETWORK BRIDGE DBC Network Bridge All-Digital Cinema Solution t the heart of a Digital B Chain system, the Crown DBC Network Bridge allows you to distribute multiple channels of digital audio over standard fast Ethernet hardware and cabling for use in traditional, e-cinema and d-cinema applications.
CINEMA `DIGITAL B-CHAIN UltraScreen Marcus Theatres Chooses Digital B-Chain™ For UltraScreen® BL Professional and Crown International products were used in the installation of a Digital B-Chain™ (DBC™) system at the Marcus Theatres Elgin Fox UltraScreen, a gigantic threestory tall screen which is a part of the new Marcus Elgin Fox Theatre in Elgin, Illinois.
AMPLIFIERS ` CINEMA Product Applications
AMPLIFIERS ` CINEMA Product Applications
IQ NETWORK IQ Network IQ Software IQ Rackmount IQ-PIPs IQ Accessories
IQ NETWORK `IQ SYSTEM® he Crown IQ Network provides a complete digital audio solution for a wide range of uses, including fixed applications such as stadiums and cinemas, as well as large touring applications. Using fast, 100-Mb, standard Ethernet networking hardware, IQ Network can provide digital audio distribution, monitoring and control, all on a single network cable.* And now, the system has been expanded, allowing control of TCP/IQ components from BSS's SoundWeb London Software.
software applications. The physical IQ Network can be wired, wireless, or both. With wireless capabilities and a laptop computer, system monitoring and correction can be performed instantly from anywhere in the facility. Easy-to-install IQ-PIP modules can be quickly added to any IQ-compatible Crown amplifier, greatly extending its capabilities. In addition the I-Tech family of amplifiers comes with networkability built in.
IQ NETWORK `IQ SOFTWARE Crown's IQ Network is controlled by powerful yet easy-to-use IQ IQwic software, as well as Soundweb London. The intuitive interface provided in both IQwicTM and IQ for Windows software suites makes the system so easy to operate, even a novice can effectively use an IQ Network. Comprehensive on-line help for every operation and IQ component is just a click away.
`ADVANTAGES • Provides access to all servers, amplifiers and speakers on the network for quick, system-wide diagnostics. • Automated error reporting allows technicians and users to learn about potential system errors before they happen. • Alerts technicians immediately of any problems, providing specific data on where to locate the problem.
IQ NETWORK `IQ RACKMOUNT IQ-USM 810 Processor/Mixer/Router—All In One he Crown IQ-USM 810 is an 8x10 mixer/processor with unique dual input processing paths. As an IQ component, it can be controlled by an IQ Network, and with its distributed intelligence capability, can continue to operate even when an IQ Network is not connected. The IQ-USM 810 can also act as a system interface to other IQ components.
IQ NETWORK `STADIUM SOUND oldier Field, the home of Chicago’s storied NFL football team the Chicago Bears, recently reopened after undergoing a massive renovation. The venerable old stadium, originally opened in 1924, had been the home field of the oldest team in the league for over 30 years. Though incremental refurbishments over the years extended the life of the facility, the team needed a new stadium on a par with other new facilities being built for NFL teams.
IQ NETWORK `IQ PIPS IQ-PIP LITE IQ-PIP USP3 SmartAmp Automation for TCP/IQ Digital Signal Processing for TCP/IQ he Crown IQ-PIP LITE is a PIP (Programmable Input Processor) input module for PIP2 compatible amplifiers. The IQ-PIP-LITE is a TCP/IQ series component. This means it connects to an IQ Network via 100 Mb Ethernet. This provides faster IQ communications than the previous current loop, IQ bus, connectivity method. The audio path in the IQ-PIP LITE is processed totally in the analog domain.
IQ-PIP USP3/CN SmartAmp Automation for TCP/IQ he Crown IQ-PIP USP3/CN is a 3rd generation DSP-based PIP™ (Programmable Input Processor) input module for PIP2 compatible amplifiers*. It connects the amplifier to a 100 Mb Ethernet network allowing it to be remotely controlled and monitored via IQ. In addition, the USP3/CN allows the transport of real-time digital audio via CobraNet over the same Ethernet network.
IQ NETWORK `I-TECH & IQ I-Tech & IQ “A marriage made in Audio Heaven” RAMMY Award-winning recording artist Nelly Furtado recently completed her twoweek “Come As You Are” Canadian tour in support of her second release entitled “Folklore.” The first date of the tour was at the 12,000-seat Molson Amphitheater in Toronto. The show featured a seven-piece band, supporting Nelly’s intriguing blend of rock, acoustic and hip-hop sounds with a Brazilian influence.
IQ NETWORK `IQ ACCESSORIES IQ-MC8 module. IQ-MC4 module not shown. IQ-MC4 & IQ-MC8 SmartAmp Automation for CTs Multichannel Amplifiers he Crown IQ-MC4 and IQ-MC8 are optional IQ control modules for the Crown CTs multichannel power amplifiers. The IQ-MC4 is the IQ module for the CTs 4200, and the IQ-MC8 is the IQ module for the CTs 8200. The modules require an IQ System with an IQ2-compatible interface.
AMPLIFIER ACCESSORIES PIP Modules CTs Multi-Channel Amp Accessories SST Input Modules CE Output Modules Other Amplifier Accessories Module Compatibility
ACCESSORIES ` PIP MODULES PIP-3632, PIP-4622, PIP-4632, PIP-USL For use with JBL ScreenArray Cinema Speaker System Crown ScreenArray PIP modules are custom two-channel crossover networks with equalization specifically designed for use with JBL® ScreenArray® cinema speaker systems installed in cinemas, studio production and post-production environments.
ACCESSORIES ` CTs MULTI-CHANNEL AMP ACCESSORIES VCA-MC4A & VCA-MC8 Remote Level Control The Crown VCA-MC4A and VCA-MC8 are optional level-control modules for the Crown CTs multichannel power amplifiers. The VCA-MC4A is for the CTs 4200, and the VCA-MC8 is for the CTs 8200. A VCA-MC module provides independent remote level control for each channel. 4-pin removable Phoenix-style barrier connectors provide the +10VDC control voltage, ground, and control lines for two amplifier channels.
ACCESSORIES ` SST INPUT MODULE Input Options for CE, CH and CL Amplifiers Basic Input Module Standard SST module on Contractor Series and CE Series amplifiers. Barrier, XLR and TRS balanced input connectors. SST-4622 custom two-channel crossover network with routing and equalization specifically designed for use with JBL model 4622 ScreenArray cinema speaker systems. PIN 2 HOT SST-SBSC 2-way stereo crossover with summed bass output.
ACCESSORIES ` CE OUTPUT MODULES Output Options for CE Series Amplifiers CE Outputs For the CE 1000, CE 2000 and CE 2000TX only. CEAS1 Provides barrier output connection in addition to the Neutrik Speakon output connection. Also includes a touch-safe connector cover. CEAS2 Provides 5-way output connection in addition to the Neutrik Speakon output connection for CE 1000, CE 2000 and CE 2000TX amplifiers. For the CE 4000 only.
ACCESSORIES ` AMPLIFIER ACCESSORIES TP-170V. Constant-Voltage Transformer Panel 1 INPUTS: COM OUTPUTS: COM 40V 50V 2 INPUTS: COM 70V 70V 100V OUTPUTS: COM 40V 50V 3 INPUTS: COM 70V 70V 100V 40V OUTPUTS: COM 50V 4 INPUTS: COM 70V 70V 100V OUTPUTS: COM 40V 50V 70V 70V 100V TP–170V The Crown® TP-170V is a rack-mountable panel with four autoformers to provide impedance matching between amplifier outputs and “constant voltage” loudspeakers.
ACCESSORIES ` MODULE COMPATIBILITY 1 IQ-PIP Lite may be installed in older PIP1-compatible amplifiers by using the USP2 Adapter Kit (functionality slightly limited when using the Adapter Kit). ACCESSORIES 2 MA-5000VZ amplifiers with serial numbers beginning with the prefix A or B are PIP2 compatible. PIP2 compatible amplifiers bear the PIP2 logo on the rear. 3 CT-210 must have optional fan installed. 4 Analog PIPs include: P.I.P.-AMCb, P.I.P.-CLP, P.I.P.-EDCb, P.I.P.-RPA and P.I.P.-RPAT.
REFERENCE Amplifier Features Comparison Chart Amplifier Specifications Warranties and Trademarks
REFERENCE ` AMPLIFIER FEATURE COMPARISON CHART 3URWHFWLRQ V\VWHPV 2'(3 -76 7KHUPDO /HYHO &RQWURO 7/& $XWRPDWLF KLJK SDVV ILOWHU 6ZLWFKDEOH KLJK SDVV ILOWHU /RZ SDVV ILOWHU XOWUDVRQLF 5), SURWHFWLRQ 3RZHU FLUFXLW EUHDNHU 3URSRUWLRQDO VSHHG IDQV $XWRPDWLF FXUUHQW DQG YROWDJH OLPLWLQJ 4XDG 0XWH &RQYHFWLRQ FRROHG QR IDQ $GYDQFHG )HDWXUHV &ODVV , %&$ 6ZLWFKLQJ SRZHU VXSSO\ *URXQGHG %ULGJH $% % %ULGJH 0RGH ,QGLFDWRU < LQSXW VZLWFK ,QSXW 6HQVLWLYLW\ VZLWFK ,2& 6WDQGE\ PRGH 3UHFLVLRQ GHWHQWHG OHYHO FRQWUROV
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
REFERENCE ` AMPLIFIER SPECIFICATIONS 78 • www.crownaudio.
REFERENCE ` WARRANTIES Crown Amplifier Warranty USA AND CANADA SUMMARY OF WARRANTY Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A. warrants to you, the ORIGINAL PURCHASER and ANY SUBSEQUENT OWNER of each NEW Crown product, for a period of three (3) years from the date of purchase by the original purchaser (the “warranty period”) that the new Crown product is free of defects in materials and workmanship.
REFERENCE ` WARRANTIES Crown Amplifier Warranty WORLDWIDE EXCEPT USA & CANADA SUMMARY OF WARRANTY Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A.
Get your crown gear! From tees to totes, Crown logo apparel and promotional items make it clear: when it comes to audio, the choice is Crown! Rugged, highquality wearable, collectible, and very usable items are available from your local Crown dealer or the Crown website at www.crownaudio.com. Reward yourself with the name that shows nothing but the best will do.
1718 West Mishawaka Road Elkhart, IN 46517-9120 P: 1(574)294.8200 E-mail: audioinfo@crownaudio.com www.crownaudio.com © 2004 Crown Audio, Inc. 136465-2 12/04 F: 1(574)294.
