Crown Full Line Catalog
TABLE OF CONTENTS AMPLIFIERS Installed Sound I-Tech Series ...............................................4 CTs Series...................................................6 CTs Multi-Channel Series ...........................8 CH Series..................................................10 CL Series ..................................................12 K Series ....................................................14 D Series ....................................................16 XLS Series .......................
AMPLIFIERS Installed Sound .4 DJ/Musician .20 Touring .28 Recording and Broadcast .38 Cinema .
AMPLIFIERS — Installed Sound I-Tech Series: Excellence Without Compromise I-T4000 I-T6000 I-T8000 Features • • • • • Amazingly high power in a 2U lightweight chassis Global power supply with power factor correction Onboard DSP Connects to TCP/IQ™ network (CobraNet input available in optional CN models, coming soon) LCD control screen allows easy setup, diagnostics, and DSP presets for various loudspeakers.
Specifications Frequency Response (at 1 watt, 20 Hz - 20 kHz): ±0.25dB. Signal to Noise Ratio below rated full-bandwidth power, A-weighted: > 105 dB Total Harmonic Distortion (THD) at full rated power: < 0.35%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to –35 dB: < 0.35%. Damping Factor (20 Hz to 100 Hz, 8 ohms): > 5000. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB. Common Mode Rejection (CMR) (20 Hz to 1 kHz): > 50 dB.
AMPLIFIERS — Installed Sound CTs Series: The New Standard CTs 600 CTs 1200 CTs 2000 CTs 3000 Features • • • • • High power density. All two channel models in a 2U chassis. New Crown Switching Power Supply for lighter weight. Selectable “Constant-Voltage” or low-impedance operation per channel. 100V direct outputs on CTs 2000, CTs 3000. Fully PIP2-compatible.
Specifications Back Panel Controls and Connectors The following applies to units in Dual mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Power Cord Connector: IEC Reset Switch: Resets the power circuit breaker. Channel Level Controls: 21-position detented, one per channel. Level Attenuation: Approx. –95 dB to 0 dB gain. High-Pass Filter: One three-position switch per channel selects between OFF, 35 Hz and 70 Hz 3rd-order filters.
AMPLIFIERS — Installed Sound CTs Multi-channel Series: The New Standard CTs 4200 CTs 8200 Features • • • • • • High power density: Four-channel model in a 2U chassis, eight-channel model in a 3U chassis. New Crown Switching Power Supply for lighter weight. Selectable “Constant-Voltage” or low-impedance (4/8 ohm) operation per channel-pair. 100V direct outputs. New “FIT” (Fault Isolation Topology) circuitry isolates fault conditions without affecting neighboring channels. Accept new MC accessory modules.
Specifications Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.5 dB. Phase Response (at 1 watt) 10 Hz to 20 kHz: ±35°. Signal-to-Noise Ratio, unweighted, below rated power (20 Hz to 20 kHz): 100 dB. Total Harmonic Distortion (THD) at full rated power, from 20 Hz to 20 kHz: < 0.1%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from 163 milliwatts to full bandwidth power: < 0.05% (typical). Damping Factor, 10 Hz to 400 Hz: > 180.
AMPLIFIERS — Installed Sound CH Series: 4/8 Ohm, 70V or 100V Per Channel CH1 CH2 CH4 Features • • • • Drives multiple impedances, with both low impedance and high impedance outputs per channel. High-pass filter for each channel provides low-frequency roll off to eliminate step down transformer saturation when used in 70V distributed systems. Rear panel detented level controls allow for accurate level settings and secure operation.
Specifications Note: All measurements apply to all models of CH series amplifiers in stereo mode with 8-ohm loads and an input sensitivity of 26-dB gain, 1-kHz at rated power unless other otherwise specified. Specifications for units supplied outside the U.S.A. may vary slightly at different AC voltages and frequencies. Power Load Impedance: Safe with all types of loads. CH1: 4 and 8 ohm Stereo; 16 ohm at 70V Stereo; 32 ohm at 100V Stereo; 8 and 16 ohm Bridge; 32 ohm at 140V Bridge; 64 ohm at 200V Bridge.
AMPLIFIERS — Installed Sound CL Series: High-Power, 2-Ohm Operation CL1 CL2 CL4 Features • • • • • POWERFUL Power Output* CL1 CL2 CL4 2-ohm Stereo 4-ohm Stereo (per channel) (per channel) 8-ohm Stereo (per channel) 560W 450W 975W 660W 1,400W** 1,200W 275W 400W 600W 4-ohm Bridge Mono 8-ohm Bridge Mono 1,100W 900W 1,950W 1,320W 2,800W** 2,400W *Maximum average power in watts at 0.5% THD, 1 kHz. **+200V line voltage provides 1,800W (2 ohm stereo) and 3,600W (4 ohm bridge-mono). www.crownaudio.
Specifications Indicators Note: All measurements apply to all models of CL series amplifiers in stereo mode with 8-ohm loads and an input sensitivity of 26-dB gain, 1-kHz at rated power unless other otherwise specified. Specifications for units supplied outside the U.S.A. may vary slightly at different AC voltages and frequencies. Signal: A green indicator for each channel which flashes when a very lowlevel signal (>–40 dBm) is present at input. May be used for troubleshooting cable runs.
AMPLIFIERS — Installed Sound K Series: Radically Different K1 K2 Features • • • • PERFORMANCE Power Output* 2-ohm Stereo 4-ohm Stereo 8-ohm Stereo 4-ohm (per channel) (per channel) Bridge-Mono Bridge-Mono K1 K2 750W 1,250W 550W 800W 350W 1,500W 500W 2,500W *Maximum average power in watts at 0.1% THD, 1 kHz. www.crownaudio.com 14 • Sealed chassis—no fan, no noise! Patented Class “I” (BCA) circuit design. Unmatched thermal efficiency; superior energy efficiency.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Frequency Response: ± 0.25 dB from 20 Hz to 20 kHz. The frequency response is band limited with an 8 Hz double integrated 3rd-order Butterworth high-pass filter and a 32 kHz 7th-order Gaussian low-pass filter. Signal to Noise Ratio (Unweighted): >100 dB below rated power. Voltage Gain (at maximum level setting): 31.5 dB (K1) or 33.
AMPLIFIERS — Installed Sound D-Series: Long-Term Favorites D-45 D-75A Features • • • • • TRIED & TRUE Power Output* 4-ohm Dual 8-ohm Dual 16-ohm Dual 8-ohm 16-ohm (per channel) (per channel) (per channel) Bridge-Mono Bridge-Mono D-45 D-75A 35W 55W 25W 40W 20W 25W *Maximum average power in watts at 0.1% THD, 1 kHz. www.crownaudio.com 16 70W 110W 50W 80W • Powerful AB+B class circuitry yields maximum efficiency with minumum crossover “notch” distortion.
Specifications The following applies to units in Dual mode with both channels driven into 8-ohm loads and an input sensitivity of 26 dB gain unless otherwise specified. Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (from 20 Hz to 20 kHz at 1 watt): +10 to –15 degrees. Signal-to-Noise Ratio below rated power (20 Hz - 20 kHz): 106 dB. Total Harmonic Distortion (THD) at full bandwidth power: 0.05% from 20 Hz to 20 kHz.
AMPLIFIERS — Installed Sound XLS Series: Power and Reliability XLS 202 XLS 402 XLS 602 Features • • • • EVOLUT I O N Power Output* 2-ohm Stereo 4-ohm Stereo 8-ohm Stereo 8-ohm (per channel) (per channel) (per channel) Bridge-Mono XLS 202 XLS 402 XLS 602 250W 570W 840W 200W 400W 600W *Maximum average power in watts at 0.5% THD, 1 kHz. www.crownaudio.com 18 145W 260W 370W 400W 800W 1,200W 4-ohm Bridge-Mono 500W 1,140W 1,680W Housed in a rugged, all-steel 2U chassis.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Sensitivity (volts RMS) for full rated power at 4 ohms, XLS 202: 0.725 XLS 402: 1.025 XLS 602: 1.26. Frequency Response (at 1 watt) 22 Hz to 20 kHz: ±0.75 dB. Phase Response (degrees at 1 watt) at 10 Hz: –10. at 20 kHz: +19. Signal-to-Noise Ratio (20 Hz to 20 kHz) A-weighted, below rated power: > 100 dB. No weighting, below rated power: > 95 dB.
AMPLIFIERS — Installed Sound CP Series: 6-Channel Flexibility CP660 Features • • • • • Six independent amplifier channels and three bridging switches provide maximum configuration flexibility. Separate gain controls on the back panel allow convenient level balancing of all channels. Super-quiet variable-speed fan with auto trigger provides silent, efficient cooling. Three Dual/Mono switches on the back panel give a broad range of flexibility in configuring your system.
Specifications Note: All measurements are related to 120VAC units 60 Hz in stereo mode with 8-ohm loads at 1-kHz at rated power unless other otherwise specified. Specifications for units supplied outside the U.S.A. may vary slightly at different AC voltages and frequencies. Power Load Impedance: Safe with all types of loads. Rated for 4 and 8 ohms in Dual mode, 8 ohms in Bridge mode Required AC Mains: North American units are 120VAC, 60-Hz only; 100 and 240VAC (±10%) 50-Hz units are available.
AMPLIFIERS — Portable PA XLS Series: Power and Reliability XLS 202 XLS 402 XLS 602 Features • • • • EVOLUT I O N Power Output* 2-ohm Stereo 4-ohm Stereo 8-ohm Stereo 8-ohm (per channel) (per channel) (per channel) Bridge-Mono XLS 202 XLS 402 XLS 602 250W 570W 840W 200W 400W 600W *Maximum average power in watts at 0.5% THD, 1 kHz. www.crownaudio.com 22 145W 260W 370W 400W 800W 1,200W 4-ohm Bridge-Mono 500W 1,140W 1,680W Housed in a rugged, all-steel 2U chassis.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Sensitivity (volts RMS) for full rated power at 4 ohms, XLS 202: 0.725 XLS 402: 1.025 XLS 602: 1.26. Frequency Response (at 1 watt) 22 Hz to 20 kHz: ±0.75 dB. Phase Response (degrees at 1 watt) at 10 Hz: –10. at 20 kHz: +19. Signal-to-Noise Ratio (20 Hz to 20 kHz) A-weighted, below rated power: > 100 dB. No weighting, below rated power: > 95 dB.
AMPLIFIERS — Portable PA CE Series: Power and Reliability CE 1000 CE 2000 CE 4000 Features • • • • 2-OHM PERFORMANCE • • Handles 2-ohm loads Front-panel detented level controls Function indicators, fan-assisted cooling, short-circuit protection Class “I” (BCA) circuitry in CE 4000 offers extra power and efficiency Selectable highpass and lowpass filters in CE 4000. Works with SST modules that provide extra functions.
Specifications* Performance Frequency Response (at 1 watt): CE 1000/2000: ±0.2 dB from 20 Hz to 25 kHz. CE 4000: ±0.25 dB from 20 Hz to 20 kHz. Phase Response (at 1 watt) 20 Hz to 20 kHz: ±15 degrees. Signal to Noise Ratio (below rated power), 20 Hz to 20 kHz: CE 1000/2000: >100 dB. CE 4000: >102 dB. Total Harmonic Distortion (THD) at rated power: 0.5% or less. Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1): CE 1000/2000, from 163 millwatts to full bandwidth power: Less than 0.1%.
AMPLIFIERS — Portable PA Xs Series: Power in Xs Xs500 Xs700 Xs900 Xs1200 Xs4300 Features • • • • • • POWER IN Xs Power Output* 2-ohm Dual** 4-ohm Dual (per channel) (per channel) Xs500 Xs700 Xs900 X1200 Xs4300 750W 900W 1,100W 1,600W — 500W 750W 900W 1,100W 300W 8-ohm Dual (per channel) 400W 450W 600W 650W 200W 4-ohm** Bridge-Mono 1,600W 1,900W 2,500W 3,000W — 8-ohm Bridge-Mono 1,450W 1,645W 2,100W 2,300W 700W *Refers to maximum average power in watts at 1kHz with 0.15% THD. **At 0.5% THD.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V Frequency Response (at 1 watt) 22 Hz to 22 kHz: ±1 dB. Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5°, –18° Signal-to-Noise Ratio: A-weighted, below rated power: > 102 dB. 22Hz to 22kHz, below rated power: > 97 dB.
AMPLIFIERS — Portable PA K Series: Radically Different K1 K2 Features • • • • • PERFORMANCE Power Output* 2-ohm Stereo 4-ohm Stereo 8-ohm Stereo 4-ohm (per channel) (per channel) (per channel) Bridge-Mono K1 K2 750W 1,250W 550W 800W 350W 1,500W 500W 2,500W *Maximum average power in watts at 0.1% THD, 1 kHz. www.crownaudio.com 28 Sealed chassis—no fan, no noise! Patented Class “I” (BCA) circuit design. Unmatched thermal efficiency; superior energy efficiency.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Frequency Response: ± 0.25 dB from 20 Hz to 20 kHz. The frequency response is band limited with an 8 Hz double integrated 3rd-order Butterworth high-pass filter and a 32 kHz 7th-order Gaussian low-pass filter. Signal to Noise Ratio (Unweighted): >100 dB below rated power. Voltage Gain (at maximum level setting): 31.5 dB (K1) or 33.
AMPLIFIERS — Installed Sound I-Tech Series: Excellence Without Compromise I-T4000 I-T6000 I-T8000 Features • • • • • EXCELLENCE Power Output* 2-ohm Dual 4-ohm Dual 8-ohm Duall (per channel) (per channel) (per channel) I-T4000 I-T6000 I-T8000 1800W 2500W 3500W 2000W 3000W 4000W 1250W 1500W 2100W *Guaranteed minimum power in watts at rated THD, 20 Hz - 20 kHz www.crownaudio.
Specifications Frequency Response (at 1 watt, 20 Hz - 20 kHz): ±0.25dB. Signal to Noise Ratio below full-bandwidth rated power, A-weighted: > 105 dB Total Harmonic Distortion (THD) at full rated power: < 0.35%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to –35 dB: < 0.35%. Damping Factor (20 Hz to 100 Hz, 8 ohms): > 5000. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB. Common Mode Rejection (CMR) (20 Hz to 1 kHz): > 50 dB. DC Output Offset: ± 3 mV.
AMPLIFIERS — Touring Macro-Tech VZ ® Series: Advanced VZ Technology Macro-Tech 3600VZ Macro-Tech 5002VZ Features • • • • • Crown’s Grounded Bridge design provides lower distortion and superior reliability. Patented ODEP (Output Device Emulation Protection) circuitry compensates for overheating and overload to keep the amplifier working when others would fail. Articulated VZ power supplies for each channel provide excellent crosstalk characteristics and the best power matching to your load.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (at 1 watt, 10 Hz to 20 kHz): ±10 degrees. Signal-to-Noise Ratio (below rated full bandwidth power), A-weighted: > 105 dB. Total Harmonic Distortion (THD) (at rated power): MA-3600VZ: 20 Hz to 1 kHz: < 0.05%. 20 kHz: < 0.1%. MA-5000VZ: < 0.
AMPLIFIERS — Touring Macro-Tech 02 Series: Advanced Reinforcement Macro-Tech 602 Macro-Tech 1202 Macro-Tech 2402 Features • • • • Enhanced PIP2™ (Programmable Input Processor) connector accepts new accessory modules that tailor the amplifier for specific applications. Balanced XLR and 1/4-inch phone jacks for each channel on the standard PIP-FXQ module.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (at 1 watt, 10 Hz to 20 kHz): ±10 degrees. Signal-to-Noise Ratio (below rated full bandwidth power), A-weighted: > 105 dB. Total Harmonic Distortion (THD) (at rated power), 20 Hz to 1 kHz: < 0.05% At 20 kHz: < 0.1%.
AMPLIFIERS — Touring Macro-Tech Biamp Series: Amplifiers for Biamped Systems Macro-Tech 24x6 Macro-Tech 36x12 Features • • • • • DUAL LEVEL Unique Dual-Level Design: Each channel has a different power level for maximum amplifier utilization in biamplified and triamplified systems. MA-36X12: Articulated VZ ® power supply for Channel 1 (3600) provides the best power matching to your load. Crown’s Grounded Bridge design provides lower distortion and superior reliability.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Reset Switches: Two back-panel switches used to reset the breakers that safeguard each power supply from overload. Indicators Performance (all located on front panel) Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (at 1 watt, 10 Hz to 20 kHz): ±10 degrees. Signal-to-Noise Ratio (below rated full bandwidth power), A-weighted: > 105 dB.
AMPLIFIERS — Touring Micro-Tech Series: Workhorse Power Micro-Tech 600 Micro-Tech 1200 Micro-Tech 2400 Features • • • • • WORKHORSE Crown’s Grounded Bridge design provides lower distortion and superior reliability. Patented ODEP (Output Device Emulation Protection) circuitry compensates for overheating and overload to keep the amplifier working when others would fail. High damping factor provides superior motion control over lowfrequency drivers for clean, accurate low end.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Reset Switches (Micro-Tech 2400 only): Two back-panel switches used to resent the breakers that safeguard each power supply from overload. Performance Indicators Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (at 1 watt, 20 Hz to 20 kHz): ±10 degrees. Signal-to-Noise Ratio (below rated full bandwidth power), A-weighted: > 105 dB.
AMPLIFIERS — Touring Xs Series: Power in Xs Xs500 Xs700 Xs900 XS1200 Xs4300 Features • • • • • • POWER IN Xs Power Output* 2-ohm Dual** 4-ohm Dual (per channel) (per channel) Xs500 Xs700 Xs900 Xs1200 Xs4300 750W 900W 1,100W 1,600W — 500W 750W 900W 1,100W 300W 8-ohm Dual (per channel) 400W 450W 600W 650W 200W 4-ohm** Bridge-Mono 1,600W 1,900W 2,500W 3,000W — 8-ohm Bridge-Mono 1,450W 1,645W 2,100W 2,300W 700W *Refers to maximum average power in watts at 1kHz with 0.15% THD. **At 0.5% THD.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V Frequency Response (at 1 watt) 22 Hz to 22 kHz: ±1 dB. Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5°, –18° Signal-to-Noise Ratio: A-weighted, below rated power: > 102 dB. 22Hz to 22kHz, below rated power: > 97 dB.
AMPLIFIERS — Recording / Broadcast D-Series: Long-Term Favorites D-45 D-75A Features • • • • • TRIED & TRUE Power Output* 4-ohm Dual 8-ohm Dual 16-ohm Dual 8-ohm 16-ohm (per channel) (per channel) (per channel) Bridge-Mono Bridge-Mono D-45 D-75A 35W 55W 25W 40W 20W 25W *Maximum average power in watts at 0.1% THD, 1 kHz. www.crownaudio.com 42 70W 110W 50W 80W • Powerful AB+B class circuitry yields maximum efficiency with minumum crossover “notch” distortion.
Specifications The following applies to units in Dual mode with both channels driven into 8-ohm loads and an input sensitivity of 26 dB gain unless otherwise specified. Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.1 dB. Phase Response (from 20 Hz to 20 kHz at 1 watt): +10 to –15 degrees. Signal-to-Noise Ratio below rated power (20 Hz - 20 kHz): 106 dB. Total Harmonic Distortion (THD) at full bandwidth power: 0.05% from 20 Hz to 20 kHz.
AMPLIFIERS — Recording / Broadcast K Series: Radically Different K1 K2 Features • • • • • PERFORMANCE Power Output* 2-ohm Stereo (per channel) K1 K2 750W 1,250W 4-ohm Stereo (per channel) 8-ohm Stereo Bridge-Mono 550W 800W 350W 500W *Maximum average power in watts at 0.1% THD, 1 kHz. www.crownaudio.com 44 4-ohm Bridge-Mono 1,500W 2,500W Sealed chassis—no fan, no noise! Patented Class “I” (BCA) circuit design. Unmatched thermal efficiency; superior energy efficiency.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Frequency Response: ± 0.25 dB from 20 Hz to 20 kHz. The frequency response is band limited with an 8 Hz double integrated 3rd-order Butterworth high-pass filter and a 32 kHz 7th-order Gaussian low-pass filter. Signal to Noise Ratio (Unweighted): >100 dB below rated power. Voltage Gain (at maximum level setting): 31.5 dB (K1) or 33.
AMPLIFIERS — Recording / Broadcast Studio Reference Series: The Industry Reference Studio Reference I Studio Reference II Features • • • • • BENCHMARK Power Output* 4-ohm Stereo 8-ohm Stereo 8-ohm 16-ohm (per channel) (per channel) Bridge-Mono Bridge-Mono Studio Reference I Studio Reference II 1,190W 565W *Maximum average power in watts at 0.1% THD, 1 kHz. www.crownaudio.
Specifications Indicators The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Enable: Shows the on/off status of the unit’s low-voltage power supply. Signal: Flashes to show audio output in each channel. IOC: Flashes if the output waveform differs from the input waveform by 0.05% or more. The LEDs act as sensitive distortion indicators to provide proof of distortion-free performance.
AMPLIFIERS — Cinema CTs Series: The New Standard CTs 600 CTs 1200 CTs 2000 CTs 3000 Features • • • • • High power density. All two channel models in a 2U chassis. New Crown Switching Power Supply for lighter weight. Provides “Constant-Voltage” or low-impedance operation per channel. 100V direct outputs on CTs 2000, CTs 3000. Fully PIP2-compatible.
Specifications Back Panel Controls and Connectors The following applies to units in Dual mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Power Cord Connector: IEC Reset Switch: Resets the power circuit breaker. Channel Level C ontrols: 21-position detented, one per channel. Level Attenuation: Approx. –95 dB to 0 dB gain. High-Pass Filter: One three-position switch per channel selects between OFF, 35 Hz and 70 Hz 3rd-order filters.
AMPLIFIERS — Cinema CTs Multi-channel Series: The New Standard CTs 4200 CTs 8200 Features • • • • • • High power density: Four-channel model in a 2U chassis, eight-channel model in a 3U chassis. New Crown Switching Power Supply for lighter weight. Selectable “Constant-Voltage” or low-impedance (4/8 ohm) operation per channel-pair. 100V direct outputs. New “FIT” (Fault Isolation Topology) design isolates fault conditions without affecting neighboring channels. Accept new MC accessory modules.
Specifications Performance Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.5 dB. Phase Response (at 1 watt) 10 Hz to 20 kHz: ±35°. Signal-to-Noise Ratio, unweighted, below rated power (20 Hz to 20 kHz): 100 dB. Total Harmonic Distortion (THD) at full rated power, from 20 Hz to 20 kHz: < 0.1%. Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from 163 milliwatts to full bandwidth power: < 0.05% (typical). Damping Factor, 10 Hz to 400 Hz: >180. Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB.
AMPLIFIERS — Cinema CL Series: High-Power, 2-Ohm Operation CL1 CL2 CL4 Features • • • • • POWERFUL Power Output* CL1 CL2 CL4 2-ohm Stereo 4-ohm Stereo (per channel) (per channel) 8-ohm Stereo (per channel) 560W 450W 975W 660W 1,400W** 1,200W 275W 400W 600W 4-ohm Bridge Mono 8-ohm Bridge Mono 1,100W 900W 1,950W 1,320W 2,800W** 2,400W *Maximum average power in watts at 0.5% THD, 1 kHz. **+200V line voltage provides 1,800W (2 ohm stereo) and 3, 600W (4 ohm bridge-mono). www.crownaudio.
Specifications Note: All measurements apply to all models of CL series amplifiers in stereo mode with 8-ohm loads and an input sensitivity of 26-dB gain, 1-kHz at rated power unless other otherwise specified. Specifications for units supplied outside the U.S.A. may vary slightly at different AC voltages and frequencies. Power Load Impedance: Safe with all types of loads. All models: 2, 4 and 8 ohm Stereo; 4, 8 and 16 ohm Bridge. Voltage Gain, 1 kHz, 1.4V sensitivity, CL1: 30.5 dB at 4/8 ohm. CL2: 32.
AMPLIFIERS — Cinema CE-1000 and CE-2000TX: Power and Reliability CE-1000 CE-2000TX Features • • • • • THX CERTIFIED THX® approved. Front-panel detented level controls. Function indicators, fan-assisted cooling, short-circuit protection. Selectable highpass and lowpass filters. Works with SST modules that provide extra functions, such as signal processing for JBL ScreenArray™ cinema speaker systems.
Specifications Indicators Note: All measurements related to 120-volt ,60-Hz units in stereo mode with 8-ohm loads and an input sensitivity of 26-dB gain at 1-kHz rated power unless other otherwise specified. Specifications for units supplied for units supplied outside the U.S.A. may vary slightly at different AC voltages and frequencies. Signal: Green LED for each channel flashes when a very low-level signal (> –40 dBm) is at input. May be used to troubleshoot cable runs.
AMPLIFIERS — Cinema XLS Series: Power and Reliability XLS 202 XLS 402 XLS 602 AMPLIFIERS — Installed Sound Power and Reliability Features • • • • Housed in a rugged, all-steel 2U chassis. Efficient forced-air fan prevents excessive thermal buildup. Electronically balanced XLR inputs; touchproof binding post and Speakon outputs. Detented level controls, power switch, and four LEDs, which indicate clip for each channel, power and fault conditions.
Specifications The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified. Performance Sensitivity (volts RMS) for full rated power at 4 ohms, XLS 202: 0.725 XLS 402: 1.025 XLS 602: 1.26. Frequency Response (at 1 watt) 22 Hz to 20 kHz: ±0.75 dB. Phase Response (degrees at 1 watt) at 10 Hz: –10. at 20 kHz: +19. Signal-to-Noise Ratio (20 Hz to 20 kHz) A-weighted, below rated power: > 100 dB. No weighting, below rated power: > 95 dB.
MICROPHONES Installed Sound .60 Portable PA/Touring .68 Recording and Broadcast .
MICROPHONES — Installed Sound: Stage and Pulpit PCC®-160 Industry-Standard Stage-Floor Mic Long recognized as an industry-standard stage-floor microphone, the half-supercardioid PCC-160 is also great for altar tables – anywhere maximum gain and articulation are essential. PCC boundary technology guarantees a natural sound free of phase interference, with sensitivity increased by 6 dB. Available in two versions: black (PCC-160) or white (PCC-160W).
LM-201 The Rugged Lectern/Pulpit Microphone Slim, rugged and unobtrusive, the LM-201 is the best choice LM-201 for pulpit and lectern applications. Its internal shock mount reduces lectern thumps. A ball-and-socket joint combined with a rugged mic arm provides quiet, long-term operation. The LM-201’s supercardioid pattern rejects background noise and reverb while improving gain-before-feedback.
MICROPHONES — Installed Sound: Conference (part 1 of 2) MB SERIES Mini-Boundary™ Microphone System Featuring an incredibly small size, the MB Series of Mini-Boundary, half-supercardioid microphones from Crown offer a wide range of features and flexibility. The miniature, low-profile designs virtually disappear when installed, yet provide the same great sound as our highly-acclaimed PCC microphone series. Best of all, the MB Series provides substantial savings compared to traditional microphones.
MB-3 Installs through table Self-contained A stand-alone unit with a built-in electronics package, the lowprofile MB-3 mounts easily into tabletops, walls or ceilings. It uses a standard male 3-pin XLR-type output and comes with a locking security ring.
MICROPHONES — Installed Sound: Conference (part 2 of 2) PCC-170 Table-Mounted Half-Supercardioid The PCC-170’s surface-mount, half-supercardioid design is equally adept in the boardroom, at the lectern, or for teleconferencing. Provides clear, natural sound free of phase interference from table sound reflections. Available in two versions: black (PCC-170) or white (PCC-170W).
PZM®-20R PZM-10, PZM-10LL Pressure Zone Microphone® for Permanent Installation Ceiling- or Wall-Mount PZMs Perfect for permanent flush-mounting in conference tables, lecterns, pulpits, walls, you name it. A hemispherical pickup pattern, rising high-frequency response and low-frequency roll-off makes the PZM-20R a great choice for clear speech pickup. It also mounts in shallow cavities or a standard electrical wall box and can be powered directly from phantom power via screw terminals.
MICROPHONES — Installed Sound: Security and Surveillance PZM-10, PZM-10LL Security and Surveillance, XLR Connector / Pigtail The PZM-10 is a low-profile omni Pressure Zone Microphone featuring a cylindrical design for ceiling, wall or tabletop installations. Intelligibility is excellent, with low frequencies below the voice range rolled off to reduce the pickup of HVAC rumble. Has XLR type output connector. The PZM-10LL has a line-level output on a pigtail cable and requires 12 to 14V DC.
PZM-11LLWR Water-Resistant Security/Surveillance Mic Similar to the PZM-11LL, the PZM-11LLWR is a weatherresistant model designed for outdoor use. A plastic membrane inside the microphone protects the mic capsule from water damage. The mic mounts in a standard electrical outlet box. Applications include fast-food restaurants, outdoor intercoms, toll booths, bridges, theme park security and home automation. Requires 12-24V AC or DC. Phantom powering by special order.
MICROPHONES — Portable PA / Touring CM-200A, CM-200ASW SASS-P MKII, SASS-HC Smooth Vocals, Excellent Instrumentals Natural Stereo Imaging The CM-200A cardioid delivers fine studio quality sound in a rugged package that withstands the toughest field conditions. Its smooth, articulate performance combined with a wide frequency range make it an excellent choice for all-around critical uses, either vocals or instruments. The CM-200ASW adds a built-in magnetic reed switch that turns the mic on and off.
CM-312, CM-312AE, CM-312AHS Headworn Flexibility CM-700, CM-700MP The CM-312A condenser mic provides hypercardioid direc- Drums and Acoustic Instruments tional characteristics with the same comfort and fit found with the headworn CM-311A. The CM-312A is ideal for live sound situations where a little less discrimination against high stage levels is required. It’s also an excellent choice for aerobics and broadcast applications. The CM-312A includes a battery/ phantom powered belt pack.
MICROPHONES — Recording and Broadcast (part 1 of 2) CM-200A Smooth Vocals, Excellent Instrumentals The CM-200A cardioid delivers fine studio quality sound in a rugged package that withstands the toughest field conditions. Its smooth, articulate performance combined with a wide frequency range make it an excellent choice for all-around critical uses. The CM-200A works especially well for close-miked lead vocals, harmony vocals and scratch vocals.
CM-700, CM-700MP Professional Recording The CM-700 is a cardioid condenser microphone for use in professional recording and sound reinforcement. It reproduces music with an accurate, natural sound. Handling up to 151 dB SPL before overload, this mic is an excellent choice for miking overhead drums or acoustic instruments. The CM700 also features a 3-position roll-off switch. A stereo matched pair of CM-700s is available as the CM-700MP.
MICROPHONES — Recording and Broadcast (part 2 of 2) CM-311AHS Differoid Noise-Cancelling Microphone for Broadcast This noise-cancelling microphone mounts on a Sony MDRV6 or MDR-7506 headphone. Its condenser capsule provides full, clear, distortion-free sound and exceptional isolation from background noise. The CM-311AHS is ideal for sports announcing and traffic helicopters. Lightweight, rugged and comfortable, the headband and mic boom are adjustable to any user.
SASS-P MKII, SASS-HC Natural Stereo Imaging MIC TIPS Low frequencies Field Recording with the SASS Electronic News Gathering (E.N.G.) High frequencies The SASS-P MK II is the latest version of our patented, stereo condenser microphone using PZM technology. A mono-compatible, near-coincident array design makes it perfect for professional recording, broadcast and sampling.
SYSTEM SOLUTIONS IQ Network .76 IQ Software .78 IQ Network Hardware Components .79 IQ Rackmount .80 IQ PIPs .82 IQ Accessories .84 PIP Modules .85 CTs Multi-channel Amplifier Accessories .86 MT Amp Modules .87 SST Input Modules .88 CE Output Modules .89 Module Compatibility .
SYSTEM SOLUTIONS — IQ System® IQ Network TCP/IQ Protocol Complete Digital Audio Solution The Crown IQ Network provides digital audio distribution, monitoring and control for a wide range of audio systems over a standard 100MB Ethernet network via Crown’s TCP/IQ™ protocol.* Control and monitoring of the entire audio system is performed using IQ components and versatile IQwic™ or IQ for Windows ® software.
Networking IQ Advantages • Provides access to all servers, amplifiers and speakers on the network for quick, system-wide diagnostics. • Automated error reporting allows technicians and users to learn about potential system errors before they happen. • Alerts technicians immediately of any problems, providing specific data on where to locate the problem.
SYSTEM SOLUTIONS — IQ System® IQ Network Software IQwic, IQ for Windows The Ease of Windows, the Power of Crown Crown’s IQ Network is controlled by powerful yet easy-to-use IQ software. The intuitive interface provided in both IQwic™ and IQ for Windows software suites makes the system so easy to operate that even a novice can effectively use an IQ Network. Beneath this easy-to-use interface, custom control features provide the in-depth control required by experienced audio professionals.
IQ Network Hardware Components Crown PIP (Programmable Input Processor) input modules allow compatible amplifiers to be controlled and monitored via IQ. Crown offers several different PIP modules with a range of features including control and monitoring, real-time load supervision, digital signal processing including filters and delay, CobraNet networked audio transport and other advanced features.
SYSTEM SOLUTIONS — IQ Rackmount IQ-USM 810 Processor/Mixer/Router—All In One The Crown IQ-USM 810 is an 8x10 mixer/processor with unique dual input processing paths. As an IQ component, it can be controlled by an IQ Network, and with its distributed intelligence capability, can continue to operate even when an IQ Network is not connected. The IQ-USM 810 can also act as a system interface to other IQ components.
IQ-RPT 3 IQ System Repeater Features The Crown IQ-RPT 3 repeater helps an IQ Network go the extra dis- • tance by increasing the length of an IQ Bus loop. It does this by reconstructing the data signal to prevent its degradation. With an IQ-RPT 3 in a system, 1,000 feet (305 m) or more can typically be added to the operating distance of an IQ Bus. And because more than one IQ-RPT 3 can be used on each IQ Bus loop, the potential is impressive.
SYSTEM SOLUTIONS — IQ PIPs IQ-PIP LITE IQ-PIP USP3 SmartAmp Automation for TCP/IQ Digital Signal Processing for TCP/IQ The Crown IQ-PIP LITE is a PIP (Programmable Input Processor) The Crown IQ-PIP USP3 is a 3rd generation DSP-based PIP input module for PIP2 compatible amplifiers. The IQ-PIP-LITE is a TCP/IQ series component. This means it connects to an IQ Network via 100 Mb Ethernet. This provides faster IQ communications than the previous current loop, IQ bus, connectivity method.
IQ-PIP USP3/CN SmartAmp Automation for TCP/IQ The Crown IQ-PIP USP3/CN is a 3rd generation DSP-based PIP™ (Programmable Input Processor) input module for PIP2 compatible amplifiers*. It connects the amplifier to a 100 Mb Ethernet network allowing it to be remotely controlled and monitored via IQ. In addition, the USP3/CN allows the transport of real-time digital audio via CobraNet over the same Ethernet network.
SYSTEM SOLUTIONS — IQ Accessories IQ-MC4 & IQ-MC8 SmartAmp Automation for CTs Multichannel Amplifiers The Crown IQ-MC4 and IQ-MC8 are optional IQ control modules for the Crown CTs multichannel power amplifiers. The IQ-MC4 is the IQ module for the CTs 4200, and the IQ-MC8 is the IQ module for the CTs 8200. The modules require an IQ System with an IQ2-compatible interface. A single IQ-MC module provides IQ control and monitoring capability to all channels of the amplifier.
SYSTEM SOLUTIONS — PIP Modules PIP-3632, PIP-4622, PIP-4632, PIP-USL For use with JBL ScreenArray Cinema Speaker Systems Crown ScreenArray PIP modules are custom two-channel crossover networks with equalization specifically designed for use with JBL® ScreenArray cinema speaker systems installed in cinemas, studio production and post-production environments.
SYSTEM SOLUTIONS — CTs Multichannel Amplifier Accessories IQ-MC4 & IQ-MC8 VCA-MC4 & VCA-MC8 SmartAmp Automation for CTs Multichannel Amplifiers Remote Level Control The Crown IQ-MC4 and IQ-MC8 are optional IQ control modules for The Crown VCA-MC4 and the Crown CTs multichannel power amplifiers. The IQ-MC4 is the IQ module for the CTs 4200, and the IQ-MC8 is the IQ module for the CTs 8200. The modules require an IQ System with an IQ2-compatible interface.
SYSTEM SOLUTIONS — MT Amplifier Modules 1-VCAP & 4-VCAP For MT, PT, PB and CSL Series Amplifiers Wall-Mount Controllers These accessory modules provide a cost effective way to add alter- Crown VCAP panels are wall-mounted panels with potentiome- native inputs to Micro-Tech, Power-Tech, Power Base and CSL Series amplifiers. (Modules must be installed by an approved Crown Factory Service Center.) Two models are available: 1-VCAP and 4-VCAP.
SYSTEM SOLUTIONS — SST Input Modules Input Options for CE, CH and CL Amplifiers Basic Input Module Standard SST module on Contractor Series and CE Series amplifiers. Barrier, XLR and TRS balanced input connectors. SST-4622 custom twochannel crossover network with routing and equalization specifically designed for use with JBL model 4622 ScreenArray cinema speaker systems. PIN 2 HOT SST-SBSC 2-way stereo crossover with summed bass output.
SYSTEM SOLUTIONS — CE Output Modules Output Options for CE Series Amplifiers For the CE 1000, CE 2000 and CE 2000TX only. CEAS1 Provides bar- CEAS2 Provides 5- rier output connection in addition to the Neutrik Speakon output connection. Also include a touch-safe connector cover. way output connection in addition to the Neutrik Speakon output connection for CE 1000, CE 2000 and CE 2000TX amplifiers. For the CE 4000 only.
SYSTEM SOLUTIONS — Module Compatibility 1 IQ-PIP Lite may be installed in older PIP1-compatible amplifiers by using the USP2 Adapter Kit (functionality slightly limited when using the Adapter Kit). 2 MA-5000VZ amplifiers with serial numbers beginning with the prefix A or B are PIP2 compatible. PIP2 compatible amplifiers bear the PIP2 logo on the rear. 3 CT-210 must have optional fan installed. 4 Analog PIPs include: P.I.P.-AMCb, P.I.P.-CLP, P.I.P.-EDCb, P.I.P.-RPA and P.I.P.-RPAT. www.crownaudio.
SYSTEM SOLUTIONS 91
ACCESSORIES Amplifier Accessories .94 Microphone Accessories .
ACCESSORIES — Amplifier Accessories TP-170V Constant-Voltage Transformer Panel 1 INPUTS: COM OUTPUTS: COM 40V 50V 2 INPUTS: COM 70V 70V 100V 40V OUTPUTS: COM 50V 3 INPUTS: COM 70V 70V 100V OUTPUTS: COM 40V 50V 4 INPUTS: COM 70V 70V 100V OUTPUTS: COM 40V 50V 70V 70V 100V TP–170V The Crown® TP-170V is a rack-mountable panel with four autoformers to provide impedance matching between amplifier outputs and “constant voltage” loudspeakers.
ACCESSORIES — Microphone Accessories Mounts, Clips, Adapters ACCESSORIES — Microphone Accessories W indscreens ASA-2 Stand adapter for the CM-200A and CM310A handheld microphones. ASA-4 Stand adapter for the CM-700 and CM150 microphones, or other 3/4-inch diameter microphones. CM-30SA Stand adapter for the CM-30 and CM-31 hanging microphones for those applications where the microphone cannot be suspended from above. CM-SM Shock mount for the CM-700 and CM150 microphones.
ACCESSORIES — Microphone Accessories Power Supplies PH-1A Single-Channel Phantom Power Supply The Crown PH-1A is a reasonably priced single-channel phantom power supply. Operating from two standard 9 volt cells or PS-24 plug-in adapter, it will power all Crown microphones, as well as other condenser microphones designed to operate with phantom power of 18 to 24 volts. PH-4B 4-Channel Phantom Power Supply The Crown PH-4B is an AC powered 4-channel power supply providing 48V DC in a phantom configuration.
ACCESSORIES 97
REFERENCE Amplifiers Specifications .100 Amplifiers and System Solutions Literature .101 Microphones Specifications .102 Microphones Literature .103 Warranties and Trademarks .104 Amplifiers Feature Comparision Chart .106 Choosing the Right Crown Microphone .108 Suggested Crown Mics .109 Microphones Frequency Response .110 Amplifier & Microphone Product Application Indexes .112 Product Index .113 Contact Information .
AMPLIFIERS — Specifications www.crownaudio.com 100 Specifications are for 120VAC, 60 Hz units only. Please contact your Crown representative for information on other units. * ≥ 200V line voltage provides 1,800W (2-ohm dual) and 3,600W (4-ohm bridge-mono). **At 0.5% THD. 1 Power per channel in Dual mode @ 1 kHz at rated THD, both channels driven (20 Hz - 20 kHz for CTs 600/1200/2000/3000). 2 Power in Bridge-Mono mode @ 1 kHz at rated THD.
AMPLIFIERS and SYSTEM SOLUTIONS — Literature Crown offers a variety of publications and guides for its line of amplifiers and IQ software/components. These are at www.crownaudio.com. Under Expert Advice, Amps, click on Tech Info. Or under Expert Advice, IQ, click on Tech Info. AMPLIFIER TECHNICAL PAPERS Crown has long been leading the audio industry with innovative technologies that provide economical solutions to real world needs.
MICROPHONES — Specifications Note: All Crown microphone elements are the electret-condenser type. * Nominal impedance – actual impedance may vary. ** Phantom powering available on special order. www.crownaudio.
MICROPHONES —Literature Crown offers a variety of publications and guides for its full line of microphones. Most are at www.crownaudio.com. Under Expert Advice, Mics, click on Tech Info to see these documents: CROWN TECHNICAL BULLETIN #3 Crown Guide to Connections for Wireless Microphone Applications For CM-10E, GLM-100E, CM-311E, CM-311AE, CM-312E and CM312AE microphones. CROWN MIC MEMO A quarterly newsletter about Crown microphones and their application. Available online at www.crownaudio.
WARRANTIES Crown Amplifier Warranty USA AND CANADA SUMMARY OF WARRANTY Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A. warrants to you, the ORIGINAL PURCHASER and ANY SUBSEQUENT OWNER of each NEW Crown product, for a period of three (3) years from the date of purchase by the original purchaser (the “warranty period”) that the new Crown product is free of defects in materials and workmanship.
WARRANTIES and TRADEMARKS Crown Amplifier Warranty WORLDWIDE EXCEPT USA & CANADA SUMMARY OF WARRANTY Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A.
AMPLIFIER FEATURE COMPARISON CHART 3URWHFWLRQ V\VWHPV 2'(3 -76 7KHUPDO /HYHO &RQWURO 7/& $XWRPDWLF KLJK SDVV ILOWHU 6ZLWFKDEOH KLJK SDVV ILOWHU /RZ SDVV ILOWHU XOWUDVRQLF 5), SURWHFWLRQ 3RZHU FLUFXLW EUHDNHU 3URSRUWLRQDO VSHHG IDQV $XWRPDWLF FXUUHQW DQG YROWDJH OLPLWLQJ 4XDG 0XWH &RQYHFWLRQ FRROHG QR IDQ $GYDQFHG )HDWXUHV &ODVV , %&$ 6ZLWFKLQJ SRZHU VXSSO\ *URXQGHG %ULGJH $% % %ULGJH 0RGH ,QGLFDWRU < LQSXW VZLWFK ,QSXW 6HQVLWLYLW\ VZLWFK ,2& 6WDQGE\ PRGH 3UHFLVLRQ GHWHQWHG OHYHO FRQWUROV 9 9 RSH
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
CHOOSING THE RIGHT CROWN MICROPHONE There’s a wide variety of Crown microphones. This guide will help you select the best Crown mic for your application. TRANSDUCER TYPE (ELEMENT TYPE) POLAR PATTERN How the mic converts sound to an electrical signal: dynamic, ribbon or condenser. How the mic picks up sound from different directions. Dynamic Has a diaphragm, an attached coil of wire, and a magnet. When sound vibrates the diaphragm, the coil generates an electrical signal.
SUGGESTED CROWN MICS FOR VARIOUS APPLICATIONS ACCORDION GLM-100 (2) taped to instrument CM-700 or CM-200A ACOUSTIC BASS Close miking: GLM-100 or CM-200A Distant miking: CM-700 ACOUSTIC GUITAR Recording: CM-700, GLM-100 or SASS Reinforcement: GLM-100, CM-200A ALTAR TABLE PCC-170W or PCC-130W AMBIENCE SASS or PZM AUDIENCE PCC-160, CM-700 or PZM BANJO CM-700, CM-200A or GLM-100 BASS See Acoustic Bass BRASS Recording: CM-700 Reinforcement: CM-700, CM-200A, or GLM-100 attached to bell FIDDLE CM-700 Singing fidd
MICROPHONES: FREQUENCY RESPONSE +15 +10 All these frequency-response curves were measured at 2 feet from the sound source except as noted. Mics with cardioid, supercardioid or hypercardioid pickup patterns have a rise in in low frequencies (called proximity effect) when used close to the source.
0 135 MB-2, MB-4 PCC-130, PCC-130SW PCC-160 PCC-170, PCC-170SW PZM-10 PZM-10LL +15 +10 +5 dB 0 –5 –10 –15 –20 –25 –30 –35 20 PZM-11LLWR PZM-11, PZM-11LL 100 1K 10K 20K PZM-185, SOUND GRABBER II +15 +10 +5 FLAT dB 0 5 10 15 20 25 LOW-CUT 30 35 20 100 1K 10K PZM-20R PZM-30D, PZM-6D FREQUENCY RESPONSE AND TONE QUALITY A flat frequency response indicates a natural tonal balance at 2 feet from the sound source, while a response rising at the high frequencies indicates a brighter sound
AMPLIFIERS — Product Application Index MICROPHONES — Product Application Index INSTALLED SOUND CTs 2-channel Series CTs Multi-channel Series CH Series CL Series I-T Series K Series D Series XLS Series CP660 INSTALLED SOUND: Stage and Pulpit PCC-160, PCC-160W CM-30, CM-30W CM-31, CM-31W LM-201P LM-300A, LM-300AL, LM-301A PORTABLE PA XLS Series CE 1000, CE 2000, CE 4000 Xs Series K Series TOURING I-T Series MA-3600VZ and MA-5002VZ MA-02 Series MA-24x6 and MA-36x12 Micro-Tech Series Xs Series STUDIO / RECO
PRODUCT INDEX POWER AMPLIFIERS MICROPHONES SYSTEM SOLUTIONS Accessories CE 1000 CE 2000 CE 2000TX CE 4000 CH1 CH2 CH4 CL1 CL2 CL4 CP660 CTs 600 CTs 1200 CTs 2000 CTs 3000 CTs 4200 CTs 8200 D-45 D-75A I-T4000 I-T6000 I-T8000 K1 K2 MA-602 MA-1202 MA-2402 MA-24x6 MA-36x12 MA-3600VZ MA-5002VZ MA-24x6 and MA-36x12 MT-600 MT-1200 MT-2400 Studio Reference I Studio Reference II XLS 202 XLS 402 XLS 602 Xs500 Xs700 Xs900 Xs1200 Xs4300 Accessories CM-30, CM-30W CM-31, CM-31W CM-200A, CM-200ASW CM-310A CM-310ASW CM
REFERENCE NOTES www.crownaudio.
CONTACT INFORMATION Addresses Crown International 1718 W. Mishawaka Rd. Elkhart, IN 46517 USA Crown International Post Office Box 1000 Elkhart, IN 46515-1000 USA Phone: 574-294-8200 FAX: 574-294-8329 Toll free: 800-342-6939 Web sites Crown Audio: http://www.crownaudio.com IQ Systems: http://www.iqaudiosystems.com Harman International: http://www.harman.com Crown Factory Service 1718 W. Mishawaka Rd.
Crown International 1718 West Mishawaka Road Elkhart, IN 46517 Tel: 574.294.8200 Fax: 574.294.8329 E-mail: audioinfo@crownaudio.com www.crownaudio.
