Specifications
PORTABLE
` SPECIFICATIONS
Performance
Frequency Response:
(at 1 watt, 20 Hz to 20 kHz): +0 dB, –1 dB
Signal-to-Noise Ratio (below rated 1kHz
power at 8 ohms):
XTi 1002/2002/4002: 100 dB (A weighted),
XTi 6002: 103 dB (A weighted)
Total Harmonic Distortion (THD): < 0.5%
Damping Factor 20 Hz to 1 kHz: > 500
Crosstalk (below rated power):
20 Hz - 1 kHz: > 70 dB
Input Impedance (nominal):
20k ohms balanced, 10k ohms unbalanced
Maximum Input Signal: +22 dBu typical
AC Line Voltage and Frequency Configura-
tions:
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
AC Line Current (120 VAC amplifier playing
1/8 power pink noise into 4 ohms per ch):
XTi 1002: 6.8A; no more than 38W at idle,
XTi 2002: 8.3A; no more than 38W at idle,
XTi 4002: 10.5A; no more than 38W at idle,
XTi 6002: 15.3A; no more than 180W at idle
Operating Temperature:
0
o
C to 40
o
C at 95% relative humidity
(non-condensing)
Indicators
Signal Indicator: Green LED, one per chan-
nel, illuminates when a very low-level signal
is present at input (may be used for trouble-
shooting cable runs).
–10 Indicator: Green LED flashes when
output signal exceeds –10 dB below clip.
–20 Indicator: Green LED flashes when
output signal level exceeds –20 dB below clip.
Ready Indicator: Green LED, one per chan-
nel, illuminates when the amplifier is ready to
produce audio.
Clip Indicator: Red LED, one per channel,
turns on at the threshold of audible distortion.
Temp Indicator: Red LED, one per
channel, illuminates under excessive tem-
perature conditions.
Power Indicator: Blue LED illuminates when
the amplifier has been turned on and has
power.
Controls
Level: Two front-panel rotary level controls,
one for each channel.
Power Switch: On/Off switch applies AC
power to the amplifier.
Sel/Prev/Next Buttons: Three buttons near
the LCD screen that are used to access menu
items and front panel lockout.
LCD Screen: Backlit liquid crystal display that
shows preset and processing status.
Integrated Processing
Input EQ: 6 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. Also adjust-
able high and low shelving filters. This 8-filter
EQ section can be bypassed.
Crossover Filters: Highpass and Lowpass
per channel. Butterworth 6/12/18/24 dB per
octave. Linkwitz-Riley 24/48 dB per Octave.
Also includes ±15 dB bandpass gain and
polarity control.
Output EQ: 8 parametric filters per channel
with adjustable Q, ±15 dB boost/cut. This
8-filter EQ section can be bypassed.
Delay: For signal alignment of driver;
50 ms of total delay.
SubHarmonic Synth: Takes the low-frequency
content of the input signal and “synthesizes”
a new signal that is the same as the input
signal but one octave lower. The new synthe-
sized signal is then mixed with the original
signal to create the effect. New users now
have control over frequency, gain, and filter
type.
Peak
x
Plus™ Limiter: User defeatable limiter
that allows users to control Threshold, Attack,
and Release times.
Presets: 50 total presets; 49 of which are
user-definable.
Input/Output Connectors
Input Connectors: XLR, one per channel
Link/Out Connector: Loop-thru signal from
input connector for linking another amplifier,
one per channel.
Output Connectors: Two Neutrik® Speakon®
NL4MP output connectors. Channel-1
Speakon® is wired with Ch. 1 and Ch. 2 out-
puts for use with optional single 4-conductor
cable. Two binding post outputs (in parallel
with Speakon® connectors).
HiQnet™ USB Connector: Type B, connects
to HiQnet™ network.
Construction
Chassis: Steel
Front Panel: Cast aluminum
Cooling: Proportional speed fan with
front-to-rear airflow.
Dimensions:
XTi 1002/2002/4002: 19” (W) x 3.5” (H)
x 12.25” (D)
XTi 6002: 19” (W) x 3.5” (H) x 16.2” (D)
Net Weight:
XTi 1002/2002/4002: 18.5 lbs (8.4kg)
XTi 6002: 24.0 lbs (10.9kg)
Shipping Weight:
XTi 1002/2002/4002: 21.5 lbs (9.8kg)
XTi 6002: 30.0 lbs (13.6kg)
Regulatory Certifications
Other Applications
Installed, Cinema, Touring
The XTi Series of Crown
®
amplifiers are professional tools designed and built for portable PA applications. The series includes
four models which are similar except for output power: XTi 1002, 2002, 4002 and 6002. All are rugged and lightweight,
and offer unmatched value in their class. XTi-Series amplifiers feature an LCD screen with speaker presets for crossover
frequencies, EQ, limiting, delay, and a subharmonic synthesizer. Other features include a switch-mode universal power supply,
useful function indicators, proportional-speed fan-assisted cooling, XLR inputs, Speakon
®
and binding-post outputs, short-
circuit protection and more.
04
Harman Pro Group | 2012
Section:
04
Harman Pro Group | 2012
Section:
Page 31