CTs Multi-Channel USP/CN Series CTs 4200USP/CN Operation Manual CTs 8200USP/CN Obtaining Other Language Versions: To obtain information in another language about the use of this product, please contact your local Crown Distributor. If you need assistance locating your local distributor, please contact Crown at 574-294-8000. This manual does not include all of the details of design, production, or variations of the equipment.
CTs Multi-Channel Power Amplifiers Important Safety Instructions Wichtige Sicherheitsinstruktionen Importantes Instructions de Sécurité Instrucciones de Seguridad Importantes 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
CTs Multi-Channel Power Amplifiers Table of Contents CTs Multi-Channel Power Amplifiers CTs 4200USP/CN Dual Important Safety Instructions ......................................................... 2 3 Operation ......................................................14 8 Network and CobraNet Basics ............................. 33 Declaration of Conformity .............................................................. 3 3.1 Precautions ...................................................................
CTs Multi-Channel Power Amplifiers CTs Multi-Channel Power Amplifiers 2 Setup (continued) 2 Setup 2.1 Unpack Your Amplifier Please unpack and inspect your amplifier for any damage that may have occurred during transit. If damage is found, notify the transportation company immediately. Only you can initiate a claim for shipping damage. Crown will be happy to help as needed. Save the shipping carton as evidence of damage for the shipper’s inspection.
CTs Multi-Channel Power Amplifiers 2 Setup (continued) CTs Multi-Channel Power Amplifiers 2 Setup (continued) 2.5 Back Panel Controls and Connectors Note: CTs 8200USP/CN is shown. Some CTs 4200USP/CN features are in different locations. K. AC Power Cord Connector Standard IEC type 320 inlet. 120V models: 15-amp. 220-240V models: 10-amp. Voltage is indicated above IEC inlet. L. Output Connectors One four-pole terminal strip for every two channels with touch-proof cover.
CTs Multi-Channel Power Amplifiers 2 Setup (continued) CTs Multi-Channel Power Amplifiers 2 Setup (continued) Figure 2.6 Balanced Input Connector Wiring 2.7 Choose Input Wire and Connectors If you will be connecting an analog audio signal to the CTs amplifier, please read this section. Figure 2.6 shows connector pin assignments for balanced wiring, and Figure 2.7 shows connector pin assignments for unbalanced wiring. See the Crown Amplifier Application Guide, available online at www.crownaudio.
CTs Multi-Channel Power Amplifiers 2 Setup (continued) 2.9.3 Bridge-Mono 16/8 Mode CAUTION: Never change the position of the Mode Switch while the amplifier power is on. See the Crown Amplifier Application Guide, available online at www. crownaudio. com, for pin assignments for commonly used connector types. BRIDGE DUAL DUAL CH 2 CH 1 Typical analog input and output wiring, along with level control and Mode Switch settings are shown in Figure 2.11.
CTs Multi-Channel Power Amplifiers CTs Multi-Channel Power Amplifiers 3 Operation (continued) 3 Operation 3.2 CobraNet and Control Module Features 3.1 Precautions Your amplifier is protected from internal and external faults, but you should still take the following precautions for optimum performance and safety: 1. Before use, your amplifier first must be configured for proper operation, including input and output wiring hookup. Improper wiring can result in serious operating difficulties.
CTs Multi-Channel Power Amplifiers 3 Operation (continued) 2. Hold the Reset/Preset switch in for two flashes of the Data light (longer than 2 seconds). 3. The Data indicator will flash rapidly for a moment. 4. Restore the audio input signals. To restore the unit including presets to factory default settings: 1. Remove all audio input signals. 2. Hold the Reset/Preset switch while applying power to the unit. 3. The Data and Preset indicator will both light. 4.
CTs Multi-Channel Power Amplifiers 3 Operation (continued) Most amplifier/load systems can be configured and supervised by following these steps: 1. Configure your audio system using a known “good” load, then enable the Load Supervision feature. 2. Provide typical program material at a level high enough to light the “test” indicator. 3. Run the system at this level until the average impedance stabilizes. This may take seconds to minutes depending on level, duty-cycle, etc. 4.
CTs Multi-Channel Power Amplifiers 4 Advanced Features 3 Operation (continued) 3.3.3 CobraNet Output Routing CobraNet output routing includes the following controls: CobraNet Transmit Bundles The amplifier can transmit up to four unique CobraNet Bundles (TxA, TxB, TxC, TxD). Each Transmit Bundle includes the following controls and monitor functions: • Receiver Count: This meter reports the number of CobraNet nodes actively receiving the Bundle being sourced to the network by this bundle.
CTs Multi-Channel Power Amplifiers 4 Advanced Features (continued) 4 Advanced Features (continued) NOTE: For more information about these Crown amplifier features, please visit the Crown website at www.crownaudio.com. 4.2 Protection Systems Your Crown amplifier provides extensive protection and diagnostic capabilities, including thermal level control, fault indicators, automatic high-pass filtering, DC protect, AC under-voltage and over-voltage protection, inrush limiting, and variable-speed fans. 4.2.
CTs Multi-Channel Power Amplifiers 5 Troubleshooting CTs Multi-Channel Power Amplifiers 5 Troubleshooting (continued) CONDITION: Power indicator is off. CONDITION: Fault indicator is on. POSSIBLE REASON POSSIBLE REASON: • The amplifier has lost AC power. • The amplifier’s Power switch is off. • CONDITION: No sound, even though the amp has power. Power LED is on without flashing and the amp is receiving an input signal. Signal indicator is flashing. The amplifier channel has stopped operating.
CTs Multi-Channel Power Amplifiers 5 Troubleshooting (continued) 6 Specifications NOTE: Actual product artwork may vary slightly. Problem: Data indicator is not flashing, even though a valid command was sent. Possible causes: • Command was not addressed to the USP/CN. • Network cable is disconnected or broken. CTs Multi-Channel Power Amplifiers The following specifications apply to all models in Dual 8/4 ohm mode with 8-ohm loads unless otherwise specified.
CTs Multi-Channel Power Amplifiers 6 Specifications (continued) CTs Multi-Channel Power Amplifiers 6 Specifications (continued) Figure 6.4 CTs 8200USP/CN Typical Output Impedance vs. Frequency Figure 6.1 CTs 8200USP/CN Typical Frequency Response (1 W) Figure 6.2 CTs 8200USP/CN Typical Phase Response (1 W) Figure 6.5 CTs 8200USP/CN Typical Crosstalk vs. Frequency Figure 6.3 CTs 8200USP/CN Typical Damping Factor vs.
CTs Multi-Channel Power Amplifiers 6 Specifications (continued) CTs Multi-Channel Power Amplifiers 7 AC Power Draw and Thermal Dissipation CTs 4200USP/CN: MINIMUM GUARANTEED POWER (in watts, 0.1% THD) 120VAC, 60 Hz units Dual Mode 4 Channels Driven 1 kHz Figure 6.1 CTs 4200USP/CN Minimum Guaranteed Power 4 Ohm 8 Ohm 70V (25 Ohm) at 0.
CTs Multi-Channel Power Amplifiers 7 AC Power Draw and Thermal Dissipation (continued) CTs Multi-Channel Power Amplifiers 8 Network and CobraNet Basics This section provides additional information about HiQnet or Network basics. For more information about any of these topics, contact Crown Technical Support. For AUX connector wiring, see Sections 3.2.7 and 4.1. AC Power Draw and Thermal Dissipation: 8.
CTs Multi-Channel Power Amplifiers 8 Network and CobraNet Basics (continued) Each component has three identifiers that are used in the HiQnet system: • Media Access Control (MAC) Address • Internet Protocol (IP) Address • HiQnet Address Let’s explain each identifier. Media Access Control (MAC) Address: This is a physical address that specifies a specific physical network component. This address is predefined during manufacture and cannot be modified.
CTs Multi-Channel Power Amplifiers CTs Multi-Channel Power Amplifiers 9 Service Crown amplifiers are quality units that rarely require servicing. Before returning your unit for service, please contact Crown Technical Support to verify the need for servicing. Remember to transport the unit in the original factory pack. A list of authorized service centers in your area can be obtained from Crown Factory Service, or online from http://www.crownaudio.com/support/servcent.htm.
CTs Multi-Channel Power Amplifiers CTs Multi-Channel Power Amplifiers 10 Warranty UNITED STATES & CANADA SUMMARY OF WARRANTY 5 AR YE Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A. warrants to you, the ORIGINAL PURCHASER and ANY SUBSEQUENT OWNER of each NEW Crown product, for a period of five (5) years from the date of purchase by the original purchaser (the “warranty period”) that the new Crown productis free of defects in materials and workmanship.
CTs Multi-Channel Power Amplifiers CTs Multi-Channel Power Amplifiers PRODUCT REGISTRATION Online registration is also available at http://crownweb.crownintl.com/webregistration. Crown Audio, Inc. 1718 W. Mishawaka Rd. Elkhart, IN 46517-9439 Phone: 574-294-8000 Fax: 574-294-8329 www.crownaudio.com *Warranty is only valid within the United States of America. For information on Warranty outside of the U.S.A, please contact your local distributor.
CTs Multi-Channel Power Amplifiers CTs Multi-Channel Power Amplifiers Crown Audio Factory Service Information Shipping Address: Crown Audio Factory Service, 1718 W. Mishawaka Rd., Elkhart, IN 46517 PLEASE PRINT CLEARLY SRA #: __________________(If sending product to Crown factory service.
