0104 095 52211 Electric Fire Model C603R WaveX Installation & Maintenance Instructions 1 110803
Parts Supplied Ref Description Illustration Qty A Electric Fire 1 B Decorative Trim 1 C Coal Bed 1 D Coal Bag 1 LABLE FOR BAG OF COALS E Spacer Frame (See Fig 2 Page 4) F Remote control (With batteries) 1 1 FLAME OFF 1 kw SAFTEY 2 kw Fittings Supplied Ref G Description Wood Screw Illustration Qty 4 H Wall Plug 6 I Cable Kit 1 J Magnets 4 K Screw No 8 x ½ (Spacer optional) 4 2 Tools required (not supplied) Electric Drill (Hammer action) Masonry bit Screwdriver (Cros
Before You Start Please read these instructions carefully before you start installation. Check the pack and make sure you have all of the parts listed on page 2. When you are ready to start, make sure that you have the appropriate tools to hand, plenty of space and a clean dry area for installation. Check that the supply voltage on the rating label is in accordance with your electricity supply.
Installation The mains plug must be accessible after installation. Ensure adequate space is maintained for the routing of the supply cord. This appliance has three installation options: Option 1 Wall or Back Panel Fixing (Screw method) For fitting the appliance into a blocked flue. Offer the firebox into the opening. Mark the holes provided, indicated by the four arrows (Fig. 1). Drill, plug and screw the firebox to the wall or back panel.
Option 3 Wire cable fixing (H) Wire Cable fixing to be used when it is undesirable to drill into a marble panel (Marble can fracture if drilled)(See Fig 3) Fig. 3 Screw eye Retaining Bush Cable fixing holes Max Height 330mm Two `screw eyes’ are fixed to the rear of the opening with wall plugs. Min height from base of opening–300mm Max height from base of opening–330mm `Screw eyes’ to be 420mm apart 420mm apart Min Height 300mm Fix two `screw eyes’ to the rear of the opening.
Flat wall fix (FOR REFERENCE ONLY) Flat wall fix is suitable for a mantel with a minimum 2 1/4" (57mm) internal rebate; remove the internal rebate from the mantel (Fig .4). Place the marble back panel into position and offer the appliance up to the opening in the back panel. Offset the panel from the wall so that it is situated against the rear trim frame of the appliance; use suitable material to bridge the space between the back panel and the wall (Fig. 4).
Trim location Place each of the four magnets (I) into the location brackets (Fig.5). If applicable remove the protective film from the trim. Fit the trim (B) ensuring positive location against magnets (Fig.6). Magnet location brackets Trim Fig.5 Fig.6 Open the bag of coals (D)(see note below) and place randomly in the channel of the coal bed (Fig.8). Place front and fret central to the trim (Fig .9 & .10). Fig.7 Fig.
Care and Use Fire operation This appliance has both manual and remote operation. For safety and to save compromising the visual look of this appliance the controls have been located behind the canopy, To access the controls press the top of the canopy as shown in Fig 11. The canopy will open out from the top to reveal the controls. Fig.11 Press here to open Open position Press here to close Power Switch Power Switch (Fig. 11). Press for Power On. Press again for power off.
Remote operation (Fig. 13) For Flame effect, hold down the Power button and press the Flame button, this will activate the light unit and produce flame flicker. Hold down Power and press 1000W button. This will activate the first element. Hold down Power and Press 2000W button. This will activate the second element. To cancel operation at any time press the button Fig.
Cleaning For general cleaning, use a soft clean duster or a soft brush, a vacuum may be used for the coals. The decorative trims for this appliance have a protective coating. Remove from the appliance before cleaning with warm soapy water and a soft cloth. NEVER USE SCOURERS, ABRASIVES OR CHEMICAL CLEANERS. Before commencing work, turn off appliance and remove plug from socket. Servicing is only to be carried out by competent/qualified persons.
Spare parts list PART DESCRIPTION Brass trim Brass front & fret (Blenheim) Brass front & fret (Newcross) Black trim Black front & fret (Blenheim) Black front & fret (Newcross) Black & brass front & fret (Blenheim) Black & brass front & fret (Newcross) Chrome trim Black & chrome front & fret (Blenheim) Black & chrome front & fret (Newcross) Magnet (manufacturers part no. N30H) Amber bulb, 15 Watts (Small Edison) Coal pack CROSSLEE PART No.
