CROMMELINS™ 45mm PORTABLE CONCRETE VIBRATOR OPERATION & INSTRUCTION MANUAL Thank you for your selection of a CROMMELINS™ 45mm Portable Concrete Vibrator. This Operation Manual explains its use, installation, checking and maintenance. We highly recommend that you retain this manual for ready reference regarding proper handling of the CROMMELINS™ 45mm Portable Concrete Vibrator. Spare Parts & Service Phone: 1300 554 524 Freecall Fax: 1800 636 281 spareparts@crommelins.com.au www.crommelins.com.
Thank you very much for purchasing a CROMMELINS™ PORTABLE CONCRETE VIBRATOR. This manual covers operation and maintenance of the CROMMELINS™ PORTABLE CONCRETE VIBRATOR. This CROMMELINS™ PORTABLE CONCRETE VIBRATOR can be used in mining, construction, councils, hire industries and general use. Please take a moment to familiarise yourself with the proper operation and maintenance procedures in order to maximise the safe and efficient use of this product.
SAFETY This manual contains important information on how to use the following portable concrete vibrator models PV45SRN and PV45RBP correctly and safely. Please read through this manual before you attempt to operate the machine. This portable concrete vibrator is designed to give safe and dependable service if operated according to the instructions. 1. Only authorised and properly trained individuals should operate this piece of equipment. 2.
APPLICATIONS Piers, pre-cast beams, foundations, stairs, walls, floors, slabs, panels, floor stumps, footings and fence posts. FUNCTIONS & CONTROLS The machine is controlled by an ON/OFF switch and a throttle lever. The motor is 4-stroke and only unleaded petrol can be used. MECHANICAL HAZARDS Do not operate the machine unless all protective guards are in place. Keep hands and feet clear of rotating and moving parts to avoid injury.
PORTABLE VIBRATOR ASSEMBLY GUIDE To fit the two parts of the portable vibrator together, lay both parts on a flat surface. Remove centre button head screw from aluminium connector and loosen the other two screws Locate drive tube into the connector and push together. If they don’t push fully together rotate one part to locate square drive on the end of the shaft to the square hole in the alloy connector. Push fully home and align the hole in the tube with the cap-screw hole.
OPERATION To start the machine place it on a flat level surface and turn the engine switch to ON. Move the choke lever to the closed position. Press the priming pump until fuel is seen in the fuel tube. Pull the starter slowly until resistance is felt, pull briskly to start but do not pull out the recoil rope to the end. Return the starter grip to the normal position. Open the choke lever as the engine warms up.
MAINTENANCE When assembling, lubricating, or adjusting any part of the machine, make sure to stop the engine and disconnect the spark plug wire. Service the engine according to the engine manufacturer’s specifications. Refer to the engine operation and maintenance manual. Maintenance: Every 8 hours or daily Check for loose bolts and nuts, retighten if necessary. Check and clean the air filter element, re-lube the element according to engine manufacturer’s recommendations.
TROUBLE SHOOTING GUIDE PROBLEM Engine won’t start, or stops suddenly Engine runs, but does not get up to operating speed CAUSE SOLUTION 1. Engine switch set to “OFF” 1. Turn switch to “ON” 2. No fuel 2. Refuel 3. Spark plug is carbonized 3. Clean the spark plug or replace it with new one 4. Fuel strainer dirty 4. Clean the fuel strainer 1. Choke “ON” 1. Choke lever “OFF” 2. Air cleaner element dirty 2.
45mm PORTABLE CONCRETE VIBRATOR PARTS DIAGRAM 5 4 4 3 2 1 11 14 10 12 9 6 2 15 13 8 7 25-1 24 23 22 12 21-1b 25 21-1a 19 18 27 20 17 16 21 9
45mm PORTABLE CONCRETE VIBRATOR PARTS LIST Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 21-1a 21-1b 22 23 24 25 25-1 26 - Part No. 7365-001 4908-15036 4900-00015 4000-03202 7365-003 7365-002 7365-004 4701-16287 7365-005 4908-15019 7365-006 4921-00131 4921-00130 4914-40806 4915-12806 7365-009 4908-15025 7365-010 4002-00608 7365-011 7365-012 7365-014 7010-015 7365-013 4913-10006 4411-06025 4451-06010 4481-06016 7365-050 4931-00530 4931-50707 Part Description End cap O-ring 1.
NOTES ................................................................................................................................................. ................................................................................................................................................. ................................................................................................................................................. ....................................................................
