TABLE OF CONTENTS SAFETY WARNINGS INSTALLATION .o s senselessness 2416 PRODUCT OVERVIEW OPERATION ..ot s s s sans s s sns 17-18 CLEANING MAINTENANCE TROUBLE SHOOTING 19 A\ pacer A\ DANGER Risk of fire or explosion, Flammable refrigerant used. Do not use mechanical devices to defrost refrigerator. Do not puncture refrigerant tubing. Consult repair manual / ewer's guide before attempting to service this product. All safety precautions must be followed. To be repaired only by trained service personnel.
1. SAFETY WARNINGS Caution: risk of fire 1) WARNING—Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. 2) WARNING—Do not damage the refrigerant circuit. 3) WARNING—Do not use electrical appliances inside the food storage compartments. of the appliance, unless they are of the type recommended by the manufacturer. 4) WARNING—DANGER: Risk of child entrapment.
2. INSTALLATION allocation When selecting a position for your unit you should make sure the floor is flat and firm, and the room is well ventilated. Avoid locating your unit near a heat source, e.g. cooker, boiler or radiator. Also avoid direct sunlight as it may increase the electrical consumption. Extreme cold ambient temperatures may also cause the unit not to perform properly. This unit is not designed for use in outdoor installation. Do not drape the unit with any covering.
persevering the Door Swing(optional) 1 2. Please prepare the following tools in advance: 1) Tools: Philips screwdriver, Allen key and straight screwdriver. 2) Parts: see parts bag. Removing the freezer door Remove the hinge guard A and cover plate C upward. Remove the upper hinge B with a Philips screwdriver, as shown in step @, Raise the freezer door upward, as shown in step @. @Remove the] upward. 3. Removing the refrigerator door Remove the middle hinge D with a Philips screwdriver.
Replacing the door accessories Remove the door hinge hardware on both doors and replace to the opposite sides of the refrigerator Replacing the refrigerator door Replace the refrigerator door on the bottom hinge E. Take the left hinge J (the parts in the accessory pouch) to be attached to the refrigerator with screws. Put the hinge shaft gasket onto hinge shaft.
9. Reattaching the handles Unscrew the handles screws P and replace them on the opposite side door. Place the handle into the handle bolts and screw it tight with the Allen key. 10. Fitting the accessories Examine the refrigerator, put the handle hole plug O, handle cover plate M, hinge hole plug F and middle beam pinon place.
outdoor Space Requirements The unit's door must be able to open fully as shown. ‘ ‘ WxD250.8 inchworm inch leveler the refrigerator To do this adjust the two leveling feet at the front of the refrigerator. If the unit is not level, the door and magnetic seal alignments. will not be covered properly. Look down from the top, clockwise and counterclockwise loosening, tightening. cleaning Before Use Wash with a damp soapy sponge and warm water, use only mild detergent.
A & Before Plugging in You must check that you have a socket which is compatible with the plug supplied with the unit. 4 Before Turning On! Do not turn on until two hours after moving the unit. interior Accessories Various glass or plastic storage shelves are included with your appliance different models have different combinations. You should always slide one of the full size glass storage shelves into the lowest set of guides, above the fruit and vegetable containers, and keep it in this position.
Features » Produces up to three pounds of ice a day, depending on th size of your . overlarge 2.8 bs or larger= 3.0 Ibs. » Stores up to six pounds of ice » Preterits overflow by automatically detecting when storage bin is luff Package contents S water supply fusing ice maker unit 1@»‘ ~ Water valve Tube damp Water inlet tubs (2) 5 1 Springfield maker mounting screws (5) sowers (2) Instruction manual i ticket ing bracket o\t lip (2) Tools and materials needed o Gl with Indies nose pliers Adjustable | Electri
Installing the ice maker Your refrigerator comes 1 up for ice maker installation. 1 Unplug the refrigerator from the wall outlet. 2 Remove the freezer shelf and ice tray rack from the freezer. 3 Remove the plug from the inside of the freezer compartment with & putty knife. 4 Peel off the label covering the ice maker hole on the back of the § Push the water inlet ibe into the small hole on back Rotate while inserting the tube until the fat s tight against the back of the refrigerator. refrigerator.
8 Secure the water inlet ube to the back of the refrigerator with two tilling screws (provided). ze together and slide the tube clamp over the flit wbe. While sill squeezing the clamp, inset one end of the plastic tube into the fill whe as far as it will go, then slide the clamp downward to capture the fill tube in place.
18 With the ice maker in one hand, plug the wiring shames connector germinal located at the top of the freezer panel. Make sure that the connection is tight. Make sure the wiring ahem: | in the hook on the back of ice maker. Wiring shames connector Terminal 11 Mount 1 9 installed in step 9. Make sure that the fill cup, then tighten the screws.
12 Adjust the leveling bracket to level the ice maker. The ice maker is level when the gap between the freezer wall and the ice maker is the same at the top and bosom. e |02 Maker L | e 51w s L €VEHNG Bracket 13 Reinstall the freezer shelf and set the ice storage bin on the shelf. = 1 accessorize T bin 14 Locate the per-punched holes at the bottom right comer of the back panel of the refrigerator.
Connect the wiring shames to the water valve, making sure that the connection is tight. 18 Grasp the other end of the plastic tube and push it firmly into the Buick-connection on the valve until it bottoms out. Plastic water supply fusing 17 Clean the back of the cabinet with a commercial household deanery, ammonia, or alcohol before applying the damps. 18 Secure the plastic water supply tubing to the back of the cabinet with ‘wo plastic clamps.
Connecting the ice maker to the water supply Before you begin, please note: This water line installation is not warranted by the refrigerator or ice maker manufacturer. Follow these instructions carefully to minimize the risk of water damage. Water hammer (water banging in the pipe) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding.
§ Place the end of the water supply line Frito & sink or bucket and flush the water supply line with water until the water runs dear. « Before making the connection to the refrigerator, be sue the refrigerator power cord is not plugged int the wall outset our refrigerator does not have a water filter, we recommend installing one if your water supply has sand or particles that could dog the screen of the refrigerator’s water valve. 10 Unscrew the plastic cap from the water infer valve and discard it.
ing usable ive. Alr in new plumbing fines may maker (o cycle two or three times before making a full tray of ice. New plumbing may cause ice to be discolored or have poor favor, Discard ice made during the first 24 hours Tips for using your automatic ice maker Remember that water quality determines the duality of ice. The ice maker should not be connected to softened water. If the water softener has problems, chemical subs tan: can damage the ice maker.
3. PRODUCT OVERVIEW Dora Shelf Colon Dial Sett Temperature control panel Qil Bor Adjustable Glass Shelves [ Vegetable Bin Door shelf Leveling Feet *All images in this instruction manual are for indication only; please refer to your individual unit for details. 4. OPERATION Temperature control f ] BEY misplay 4 Once initially powered on, the display screen (including the key light) is on full display for 3 seconds, and then operates as the displayed middle shift.
value after 5 seconds. From left to right, the temperature is lower. The shift regulation is: 4.3The Standby Control Function Press SET button for 3 seconds then refrigerator is in standby mode, this temporarily cease temperature control, press SET button for 3 seconds then refrigerator returns o normal working mode temperature Control Operation 1. Refrigerator initial setting of fresh compartment control panel is 3, for freezer compartment, the initial setting is Mid position. — 2.
6. MAINTENANCE carfare When Handling / Moving Your Unit Hold the unit around its sides or base when moving it. Under no circumstances should it be lifted by holding the edges of the top surface. Remove the leveling feet before moving. servicing The unit should be serviced by an authorized engineer and only genuine spare parts should be used. Under no circumstances should you attempt to repair the unit yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunction.
