User’s Manual 3.3 Cu.Ft. Compact Refrigerator MODEL: CCR33CE1B BEFORE USING YOUR PRODUCT: Please read this manual carefully all safety rules & operating instructions. Keep this manual for future refrence.
Safety Warnings • For your continued safety and to reduce the risk of injury or electric shock, please follow all the safety precautions listed below. • Read all instructions carefully before using the unit and keep them for future reference. • Retain the manual. If you pass the unit onto a third party, make sure to include this manual.
Installation When selecting a position for your unit you should make sure the floor is flat and firm, and the room is well ventilated with an average room temperature of between 60.8°F and 90°F. Avoid locating your unit near a heat source, e.g. cooker, boiler or radiator. Also avoid direct sunlight as it may increase the electrical consumption. Extreme cold ambient temperatures may also cause the unit not to perform properly. This unit is not designed for use in a garage or outdoor installation.
2. Remove the top right hinge cover. 3. Undo the screws. Then remove the hinge bracket. 4. Remove the top left screw cover. 5. Move the core cover from left side to right side. And then lift the door and place it on a padded surface to prevent it from scratching.
6. 7. Remove the screws and bottom hinge. Then remove the adjustable feet from both side. Unscrew Unscrew and remove the bottom hinge pin, turn the bracket over and replace it. Unscrew Screw 8. Refit the bracket fitting the bottom hinge pin. Replace both adjustable feet.
9. Place the door back on. Ensure the door is aligned horizontally and vertically so that the seals are closed on all sides before finally tightening the top hinge. 10. Insert the hinge bracket and screw it to the top of the unit. 11. Use a spanner to tighten it if necessary. 12. Put the hinge cover and the screw cover back. 13. With the door closed, check that the door is aligned horizontally and vertically and that the seals are closed on all sides before finally tightening the bottom hinge.
Installation Leveling the Unit To do this adjust the two leveling feet at the front of the unit. If the unit is not level, the door and magnetic seal alignments will not be covered properly. Cleaning Before Use Wipe the inside of the unit with a weak solution of bicarbonate soda. Then rinse with warm water using a ‘wrung-out’ sponge or cloth. Wash the shelf in warm soapy water and dry completely before replacing in the unit. Clean the exterior of the unit with a damp cloth.
Product Overview
Operation Operation Switching On Your Unit 1. 2. 3. 4. Connect the mains cable to the mains socket. The internal temperature of your unit is controlled by a thermostat. There are six settings, of which position 5 is the coldest and position 0 turns the unit off. Adjust the thermostat control dial to the desired position, bear in mind that the higher the number, the lower the temperature. Position 3 recommended setting when operating at normal room.
Shopping for Chilled Foods • Take a quick look at the chilled food package and make sure it is in perfect condition. • Try to keep chilled food together while shopping and on the journey home as this will help to keep the food cold. • Don’t buy chilled food unless you can chill it right away. Specially insulated bags can be bought from most supermarkets and hardware shops. These bags can keep chilled food cold for longer while transporting.
Cleaning Defrosting Frost may accumulate on the inner rear surface of the appliance which will automatically defrost during the off cycle of the compressor. Water is channelled via the drain hole to the collection tray above the compressor where it will evaporate. Please ensure the drain hole is checked and cleaned on a regular basis so water can exit the storage compartment. Cleaning the Interior and the Exterior of the Unit • Remove the shelf before cleaning.
Maintenance Maintenance Changing the Internal Light 1. Before carrying out the bulb replacement always adjust the thermostat control dial to Position 0, then disconnect the mains supply. 2. Use a flat bladed screwdriver and gently pry off the light bulb cover. 3. Remove the old bulb by unscrewing in an counter clockwise direction. 4. Replace with a new bulb (10W SES). 5. Refit the light bulb cover and reconnect the unit to the mains supply and switch on by adjusting the thermostat.
