Crestron TPS-VID-1/TPS-VID-2 Video Card for TPS/Tilt Panel Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2002 Crestron Electronics, Inc.
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel Contents Video Card for TPS/Tilt Panel: TPS-VID-1/TPS-VID-2 1 Introduction Features and Functions Specifications Physical Description Industry Compliance Installation and Hookup Setup Configuring the Touchpanel VT Pro-e Setup SIMPL Windows Setup Problem Solving Troubleshooting Further Inquiries Future Updates Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty Operations & Installation Guide - DOC.
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel Video Card for TPS/Tilt Panel: TPS-VID-1/TPS-VID-2 Introduction Features and Functions The TPS-VID-1 and TPS-VID-2 video cards are designed for Crestron’s Isys™ TPS-4500, TPS-5000, and TPS-6000 tilt touchpanels. Each card contains a video digitizer that allows video signals to be displayed on a touchpanel.
Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 The TPS-VID-1 can automatically detect composite or S-video. The TPS-VID-2 uses the “C” input for a second composite video source (on the TPS-VID-2, Composite/S-Video can be auto-detected only when input signal 2 is not used). Video signals to the touchpanel are supplied through a Crestron TPS interface module (IMC) that is provided with the touchpanel or an optional TPS wall-mounted interface module (IMW).
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel Specifications of the TPS-VID-1/VID-2 SPECIFICATION DETAILS Power Requirements TPS-VID-1: 7 Watts (0.29 Amp @ 24 VDC) TPS-VID-2: 12 Watts (0.50 Amp @ 24 VDC) Control System Update Files1,2,3 2-Series Control System CEN/CN-TVAV CNMSX-AV/PRO CNRACKX/-DP ST-CP Isys™ Touchpanel Firmware4 VT Pro-e Programming Software1 Video Types Video Formats Video Format Detection Operating Temperature and Humidity Dimensions and Weight Version C2-2004.
Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 NOTE: Crestron software and any files on the Crestron website are for Authorized Crestron dealers only. New users may be required to register to obtain access to certain areas of the site (including the FTP site). Physical Description The TPS-VID-1 and TPS-VID-2 card, shown in the following diagrams below, is a printed circuit board (PCB) that is designed for installation into a dedicated expansion slot on the touchpanel motherboard.
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel TPS-VID-1/VID-2 Top View 3.35 in (8.51 cm) 2.41 in (6.12 cm) 5.93 in (15.06 cm) NOTE: The TPS-VID-1 circuit board is slightly less populated than the TPS-VID-2 Industry Compliance As of the date of manufacture, the card has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling (N11785). NOTE: This device complies with part 15 of the FCC rules.
Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 procedure while wearing a grounding strap that is properly grounded and on a grounded workstation to avoid damaging the TPS-VID card and/or the touchpanel. CAUTION: To prevent stripping of screw heads, threads, or mounting holes, DO NOT overtighten screws. Tighten only to the specification listed in the individual step(s).
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel TPS-VID-1/VID-2 Installation (1 of 6) – Remove Touchpanel Base Cover Screws CLEAN PANEL WITH SOFT CLOTH ONLY ELECTRONICS, INC Rockleigh, NJ 07647 U.S.A. READ INSTRUCTION MANUAL BEFORE OPERATING NO USER SERVICABLE PARTS UNDER THIS COVER ELECTRONICS, INC Rockleigh, NJ 07647 U.S.A. FCC ID: EROTPS-6000 SEE MANUAL USE POWER PACK PW-2420RU TPS-6000 ZA***** C000000 6. Place the touchpanel upright on the work surface. 7.
Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 8. Align the pins on the touchpanel interface connector of the TPS-VID-1 or TPS-VID-2 with the touchpanel motherboard connector. DO NOT force pins into connector. Press the TPSVID-1/VID-2 until the pins are fully seated. Make sure that the screw holes of the card align with the mounting posts on the motherboard. Refer to the following diagram for a detailed view. TPS-VID-1/VID-2 Installation (3 of 6) – Install TPS-VID-1/VID-2 9.
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel TPS-VID-1/VID-2 Installation (4 of 6) – Install TPS-VID-1/VID-2 Mounting Screws 10. Position the touchpanel base cover onto the base by tilting the front of the cover downward under the touchpanel pivot and lowering the base cover. 11. Hold the touchpanel base cover in place and position the touchpanel face-down onto a padded surface to prevent scratching of the screen. 12.
Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 TPS-VID-1/VID-2 Installation (5 of 6) – Re-install Touchpanel Base Cover Screws CLEAN PANEL WITH SOFT CLOTH ONLY ELECTRONICS, INC Rockleigh, NJ 07647 U.S.A. READ INSTRUCTION MANUAL BEFORE OPERATING NO USER SERVICABLE PARTS UNDER THIS COVER ELECTRONICS, INC Rockleigh, NJ 07647 U.S.A.
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel the cable assembly to the NET/VIDEO port of the appropriate interface module (TPS-IMC is shown) or to the TPSBLOCK-10 interface (refer to the latest version of the TPSBLOCK-10 Installation Guide, Doc. 5979 for functional and physical description). NOTE: When connecting the Net/Video cable from the interface module to the touchpanel, exceeding a cable length of 30 feet will significantly degrade the video signal.
Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 NOTE: When using the TPS-VID-2 for receiving two composite video sources, the “Comp/Y” connection will be used for Video Source 1 while the chroma (C) connection will be used for Video Source 2. NOTE: A variety of video wiring combinations can be used. For example, Signal 1 can be connected to the BNC connector while Signal 2 can use the twisted pair connector.
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel SETUP MENU (TPS-VID-1 shown) NOTE: If the TPS-VID-1 is installed, a single “Video” button will be displayed. If the TPS-VID-2 is installed, buttons labeled “Video 1” and “Video 2” will be displayed instead of the single “Video” button. NOTE: If the video card is not properly installed, the “Video” button(s) will not be displayed. 2. Select the Video button from the SETUP MENU to set preferences for the video source.
Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 Video Setup 3. The touchpanel can be configured to auto-detect the signal type (S-Video or Composite) coming in to the touchpanel or can be set to a specific signal type (S-Video or Composite). Select the appropriate signal type. NOTE: When configuring the TPS-VID-2, the Video 1 signal type can be automatically detected as long as one signal is sent to the touchpanel.
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel Video Setup Details (continued) VIDEO SCREEN BUTTONS Saturation Hue Fast Motion / Still Video (toggle) Soft / Sharp (toggle) Default Return DESCRIPTION Use to increase or decrease image saturation. Use to shift the color balance. The Fast Motion setting eliminates motion artifacts caused by the difference between the first and second halves of a video field and softens the image.
Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 Selecting the Video Source NOTE: If the card is not present, the Crestron Viewport displays a warning message during the upload and the video window remains blank. For further information regarding video window objects, refer to the VT Pro-e help file. SIMPL Windows Setup The touchpanel does not require special programming in SIMPL Windows to display video.
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. TPS-VID-1/VID-2 Troubleshooting TROUBLE Video window touchpanel has no display. POSSIBLE CAUSE(S) Improper video connection. Incorrect video cable used. Incorrect video format selection. Incorrect firmware/software.
Video Card for TPS/Tilt Panel Crestron TPS-VID-1 & TPS-VID-2 TPS-VID-1/VID-2 Troubleshooting (continued) TROUBLE POSSIBLE CAUSE(S) Video colors are wrong and/or moving Touchpanel is set to Auto-Detect or S-Video when two composite signals plugged into TPS-IMC. CORRECTIVE ACTION Switch to “Composite” video.
Crestron TPS-VID-1 / TPS-VID-2 Video Card for TPS/Tilt Panel Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Crestron Electronics, Inc. Operations & Installation Guide - DOC. 6059 15 Volvo Drive Rockleigh, NJ 07647 12.02 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
