Crestron TPMC-CH-IMC Interface Module Operations Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2005 Crestron Electronics, Inc.
Crestron TPMC-CH-IMC Interface Module Contents Interface Module: TPMC-CH-IMC 1 Introduction......................................................................................1 Features & Functions.............................................................1 Specifications.........................................................................3 Physical Description ..............................................................4 Industry Compliance.....................................................
Crestron TPMC-CH-IMC Interface Module Interface Module: TPMC-CH-IMC Introduction Features & Functions The TPMC-CH-IMC is an interface module designed for, and included with the Crestron TPMC-15-CH and TPMC-17-CH tilt touchpanel media centers. The interface module expands the configuration possibilities of the TPMC-15-CH and the TPMC-17-CH by allowing unbalanced video signals (via BNC) and balanced/unbalanced audio signals to be connected to the touchpanel’s CAT5 inputs and outputs.
Interface Module Crestron TPMC-CH-IMC The following block diagram illustrates the function of the TPMC-CH-IMC. Block Diagram of the TPMC-CH-IMC 2 • Interface Module: TPMC-CH-IMC Operations Guide - DOC.
Crestron TPMC-CH-IMC Interface Module Specifications The following table provides a summary of specifications for the TPMC-CH-IMC.
Interface Module Crestron TPMC-CH-IMC Physical Description The TPMC-CH-IMC, shown in the following diagram, is supplied with the TPMC-15-CH and TPMC-17-CH tilt touchpanel media centers. The module is housed in a black enclosure with a silk-screened top panel. A Light Emitting Diode (LED) indicating power, a network connector, and connectors for video input, audio input, and audio output are located on one side of the unit.
Crestron TPMC-CH-IMC Interface Module Physical Views of the TPMC-CH-IMC VIDEO (RED) LABEL 6.83 in (17.35 cm) AUDIO (BLUE) LABEL 7.30 in (18.54 cm) 3.95 in (10.02 cm) 1.75 in (4.45 cm) Ø 0.23 in (0.58 cm) 4 PLACES FOR RACK MOUNTING 1.29 in (3.26 cm) Ports There are seven ports that serve various functions on the TPMC-CH-IMC. Refer to the following diagrams and descriptions of each port. NET This 4-position mini-terminal block connector is used to connect to other Cresnet peripherals in a system.
Interface Module Crestron TPMC-CH-IMC VIDEO The video input consists of three BNC connectors for unbalanced video signals. The component, composite or S-video input signal from an external video source is connected to these ports. AUDIO IN The 5-position mini-terminal block connector mates with the included connector which is wired to an external audio source and provides balanced and/or unbalanced audio input. Description of the pinouts is shown in the following table.
Crestron TPMC-CH-IMC Interface Module VIDEO (To Panel) This RJ-45 connection mates with the TPMC-15-CH or TPMC-17-CH touchpanel. This port provides component, composite or S-video input to the touchpanel over CAT5 wiring. Description of the pinouts is shown in the following table.
Interface Module Crestron TPMC-CH-IMC Industry Compliance As of the date of manufacture, the TPMC-CH-IMC has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules.
Crestron TPMC-CH-IMC Interface Module NOTE: Do not power up system until all wiring is verified. Care should be taken to ensure data (Y, Z) and ground (G) connections are not crossed when connecting the TPMC-CH-IMC. When calculating the wire gauge for a particular Cresnet run, the length of the run and the Cresnet power usage of each Cresnet unit to be connected must be taken into consideration.
Interface Module Crestron TPMC-CH-IMC wires that share a pin on the network connector, and tin the twisted connection. Apply solder only to the ends of the twisted wires. Avoid tinning too far up the wires or the end becomes brittle. Insert the tinned connection into the Cresnet connector and tighten the retaining screw. Repeat the procedure for the other three conductors. NOTE: For larger networks (i.e.
Crestron TPMC-CH-IMC Interface Module Hardware Hookup The TPMC-CH-IMC serves as an interface between the touchpanel and the Cresnet system. Refer to the illustration after this paragraph for proper connections; apply power last. When making network connections to a control system or Cresnet peripherals, refer to “Network Wiring” on page 8.
Interface Module Crestron TPMC-CH-IMC Wiring for Audio Input: Unbalanced (left) and Balanced (right) L R L +-G+- Left Shield + Jumpers + Shield Right R +-G+- + + Shield Wiring for Audio Output: Unbalanced (left) and Balanced (right) L R L +-G+- R +-G+Shield + Shield Right Shield AMP + Left 12 • Interface Module: TPMC-CH-IMC + Right AMP + Left Operations Guide - DOC.
Crestron TPMC-CH-IMC Interface Module Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. TPMC-CH-IMC Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Touchpanel does not function. Touchpanel is not communicating to the network. Use Viewport (via SIMPL Windows or VT Pro-e) to poll the network. Verify network connection to the touchpanel.
Interface Module Crestron TPMC-CH-IMC Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www.crestron.com) for a listing of Crestron worldwide offices.
Crestron TPMC-CH-IMC Interface Module Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide - DOC. 6345 (2012969) 04.05 Specifications subject to change without notice.
