Crestron TPMC-4SMD 4.
Regulatory Compliance As of the date of manufacture, the TPMC-4SMD has been tested and found to comply with specifications for CE marking. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Crestron TPMC-4SMD 4.3” Designer Touch Screen Contents 4.3” Designer Touch Screen: TPMC-4SMD 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications................................................................................................................. 5 Specifications .....
Crestron TPMC-4SMD 4.3” Designer Touch Screen 4.3” Designer Touch Screen: TPMC-4SMD Introduction With its clean, contoured appearance, the TPMC-4SMD Designer Touch Screen from Crestron® makes an elegant statement in any environment. Perfectly at home in the most contemporary residence or modern office building, its high tech good looks underline its power for simplifying everyday tasks and functions throughout any facility, all in a very affordable device that is versatile and easy to install.
4.
Crestron TPMC-4SMD 4.3” Designer Touch Screen • Smart Graphics also includes the Smart Sizing™ feature, which allows the same user interface to be viewed on different size screens. White Backlit Buttons The TPMC-4SMD comes standard with 10 programmable “hard key” push buttons for quick access to commonly used functions. Each button features a translucent button cap with white LED backlighting. The backlighting is fully dimmable, either globally or separately for the left and right side.
4.3” Designer Touch Screen Crestron TPMC-4SMD Occupancy Sensing Crestron GLS series room occupancy sensors can be connected directly to the TPMC-4SMD to allow automation of the room’s lighting, climate control and other devices. Simple, Versatile Mounting The TPMC-4SMD installs easily on virtually any mounting surface.
Crestron TPMC-4SMD 4.3” Designer Touch Screen Applications The following diagram shows a TPMC-4SMD in a typical application. TPMC-4SMD in a Typical Application Operations & Installation Guide – DOC. 7027E 4.
4.3” Designer Touch Screen Crestron TPMC-4SMD Specifications Specifications for the TPMC-4SMD are listed in the following table. TPMC-4SMD Specifications SPECIFICATION DETAILS Touch Screen Display Display Type TFT active matrix color LCD Size 4.
Crestron TPMC-4SMD 4.
4.3” Designer Touch Screen Crestron TPMC-4SMD Physical Description This section provides information on the connections, controls and indicators available on the TPMC-4SMD. TPMC-4SMD Physical View 8 • 4.3” Designer Touch Screen: TPMC-4SMD Operations & Installation Guide – DOC.
Crestron TPMC-4SMD 4.3” Designer Touch Screen TPMC-4SMD Overall Dimensions (Front, Bottom and Rear Views) 1 1 3.47 in (89 mm) 6.20 in (158 mm) 2 0.75 in (19 mm) 1.21 in (31 mm) 0.46 in (12 mm) 3 4 1.70 in (44 mm) 2.36 in (60 mm) 2.00 in (51 mm) 3.25 in (83 mm) Operations & Installation Guide – DOC. 7027E 4.
4.
Crestron TPMC-4SMD 4.3” Designer Touch Screen Setup Network Wiring When wiring the Ethernet network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (www.crestron.com/calculators).
4.3” Designer Touch Screen Crestron TPMC-4SMD on the left side of the panel twice in sequence (1, 2, 3, 4, 1, 2, 3, 4). Refer to the following illustration for push button numbering. Push Button Layout and Join Number Assignment The “Panel Setup Options” menu opens. The functions provided by each button are detailed in subsequent paragraphs.
Crestron TPMC-4SMD 4.3” Designer Touch Screen “Ethernet Setup” Menu Touch Control System Settings to access the “Control System Interface” menu, shown in the illustration below. The “Control System Interface” menu contains buttons for eight IP Table slots as well as Add IP, Edit IP and Remove IP buttons to facilitate editing entries. The Auto Discover button toggles between Enabled and Disabled. “Control System Interface” Menu To add an IP entry to a blank slot, first touch Add IP.
4.3” Designer Touch Screen Crestron TPMC-4SMD Touch the IP Address / Hostname button. The on-screen keyboard opens, as shown in the illustration below. On-Screen Keyboard Touch CLEAR to remove any previous entry. Then enter the address required. Touch OK to accept the entry or CANCEL to cancel the entry. This hides the onscreen keyboard and returns the display to the “Edit Control System Settings” screen.
Crestron TPMC-4SMD 4.3” Designer Touch Screen Confirm IP Table Entry Removal Screen Touch OK to confirm the removal or touch CANCEL to cancel the removal. The display returns to the “Control System Interface” menu (refer to the illustration at the bottom of page 13). From the “Control System Interface” menu, touch Back to return to the “Ethernet Setup” menu. On the TPMC-4SMD, DHCP is enabled by default.
4.3” Designer Touch Screen Crestron TPMC-4SMD “Edit IP Address Settings” Screen (Showing DNS and WINS Servers) Display Settings On the “Panel Setup Options” menu, touch Display Settings to enter the “Display Settings” menu, shown in the illustration below. “Display Settings” Menu The “Display Settings” menu provides controls to adjust Key LED Brightness and LCD Brightness in addition to providing buttons to enter the Key LED Options and LCD Wake Options screens.
Crestron TPMC-4SMD 4.3” Designer Touch Screen “Key LED Options” Screen The “Key LED Options” screen provides controls for turning the Key LEDs State when in Standby function ON or OFF. Touch Back to return to the “Display Settings” menu. From the “Display Settings” menu, touch LCD Wake Options to display the “LCD Wake Options” screen, shown in the illustration below.
4.3” Designer Touch Screen Crestron TPMC-4SMD “Audio Settings” Screen The “Audio Settings” screen provides controls for Master Volume, KeyClick Volume, Wave Volume and Mute controls for all three, as well as a Play Test Wave button. Touch Back to return to the “Panel Setup Options” menu. Standby Setup On the “Panel Setup Options” menu, touch Standby Setup to display the “Standby Timeouts” screen, shown in the illustration below.
Crestron TPMC-4SMD 4.3” Designer Touch Screen “Diagnostics” Menu The “Diagnostics” menu displays information about Total RAM, Free RAM, Link Status, Control Connection, MAC and IP addresses and provides Keypad Test, Touch Test, Sensor Test, Calibrate Touch, Mic Test, and Test Patterns buttons. Touch Back to return to the “Panel Setup Options” menu. From the “Diagnostics” menu, touch Keypad Test to display the “Diagnostics – Keypad Test” screen.
4.3” Designer Touch Screen Crestron TPMC-4SMD Touch Test Screen During touch screen calibration, a crosshair appears at the center of the screen. Touch the center of the crosshair, which then moves to the upper left part of the screen. Touch the center of the crosshair and it moves to another part of the screen. Continue touching the center of the crosshair at each new location until calibration is complete. NOTE: When touching the screen during calibration, be as accurate as possible.
Crestron TPMC-4SMD 4.3” Designer Touch Screen Mic Test In Progress Screen Speak into the microphone on the front of the TPMC-4SMD and the recording is played back to confirm the microphone is functioning. After playback, the button reverts to its original Mic Test label. On the “Diagnostics” menu, the Test Patterns button to display the “Test Patterns” menu, shown in the illustration below.
4.3” Designer Touch Screen Crestron TPMC-4SMD Changing the Button Inserts The TPMC-4SMD ships with 10 “hard key” push buttons for quick access to commonly used functions. For a clean appearance, either column of buttons may be removed and covered using the no-button covers provided. To change the inserts, use the following procedure: 1. Insert a small, slot head screwdriver into the appropriate hole on the bottom of the TPMC-4SMD to release its cover. Refer to the following illustration.
Crestron TPMC-4SMD 4.3” Designer Touch Screen TPMC-4SMD with No-Button Covers Installation The TPMC-4SMD touch screen installs simply and cleanly into a standard electrical box or on to virtually any flat surface. A table top enclosure, the TTK-4SM and swivel mount, SMK-4SM are also available (both sold separately). For mounting onto a flat surface, use the MSMK-4SM Multi-Surface Mounting Kit (sold separately). The TPMC-4SMD is supplied with screws for installation into an electrical box.
4.3” Designer Touch Screen Crestron TPMC-4SMD NOTE: Use the left and right screw holes for attachment to the electrical box. Mounting the TPMC-4SMD into an Electrical Box 3. Carefully position the front of the TPMC-4SMD over the back panel and gently snap it into place, as shown in the following illustration. Snap the TPMC-4SMD into Place 24 • 4.3” Designer Touch Screen: TPMC-4SMD Operations & Installation Guide – DOC.
Crestron TPMC-4SMD 4.3” Designer Touch Screen 4. Use two of the included #04-40 x 1/4” screws to secure the TPMC-4SMD, as shown in the following illustration: a. For standard applications, use the Phillips screws (2007152 or 2007160). b. For secure applications, use the security type Torx screws (2025311 or 2025312) along with the included Torx screwdriver bit (2025915). NOTE: Parts 2007152 and 2025311 come with black models. Parts 2007160 and 2025312 come with white models.
4.3” Designer Touch Screen Crestron TPMC-4SMD Mounting in a European Electrical Box To mount the TPMC-4SMD into a European electrical box, use the following procedure: 1. Insert a small slot head screwdriver into the hole shown in the illustration at the top of page 21 and gently separate the back of the TPMC-4SMD. 2. Use the two included #4B x 3/4” screws (2019088) to attach the back panel to the electrical box, as shown in the following illustration.
Crestron TPMC-4SMD 4.3” Designer Touch Screen Hardware Hookup Make the necessary connections as called out in the illustration that follows this paragraph. Apply power after all connections have been made. When making connections to the TPMC-4SMD, use Crestron power supplies for Crestron equipment.
4.3” Designer Touch Screen Crestron TPMC-4SMD Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs, projects or firmware) can be transferred to the control system (or device).
Crestron TPMC-4SMD 4.3” Designer Touch Screen Programs, Projects and Firmware Program, project or firmware files may be distributed from programmers to installers or from Crestron to dealers. Firmware upgrades are available from the Crestron Web site as new features are developed after product releases. One has the option to upload programs and projects via the programming software or to upload and upgrade via the Crestron Toolbox.
4.3” Designer Touch Screen Crestron TPMC-4SMD Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. TPMC-4SMD Troubleshooting TROUBLE Device does not function. TPMC-4SMD is not responding. TPMC-4SMD boots up in setup screens every time. POSSIBLE CAUSE(S) CORRECTIVE ACTION Device is not communicating with the network.
Crestron TPMC-4SMD 4.3” Designer Touch Screen Further Inquiries To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or refer to the listing of Crestron worldwide offices on the Crestron Web site (www.crestron.com/offices) for assistance within a particular geographic region. To post a question about Crestron products, log onto the Online Help section of the Crestron Web site (www.crestron.com/onlinehelp).
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 7027E (2028205) 02.15 Specifications subject to change without notice.
