Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Operations Guide
This document was prepared and written by the Technical Documentation department at: Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Regulatory Compliance As of the date of manufacture, the SWE-8 have been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Contents Sonnex™ Multiroom Audio Expander, 8 Zone: SWE-8 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications..........................................................................................................
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Sonnex™ Multiroom Audio Expander, 8 Zone: SWE-8 Introduction The SWE-8 is an 8-zone expansion switcher for the Sonnex™ Multiroom Audio System (SWAMP-24X81) from Crestron®. It provides eight zone outputs consisting of four analog line-level and four S/PDIF digital outputs. All eight outputs also include Crestron Home® (CH) CAT5 balanced audio outputs for long-distance wiring applications.
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 Crestron Home CAT5 Audio Distribution The CH CAT5 balanced outputs enable long-distance wire runs up to 500 feet (152 meters) to feed remote equipment such as powered subwoofers and AV receivers located throughout the house. The CH signal is easily converted to unbalanced line-level at each remote location using an ABAR-1 CAT5 Balanced Audio Receiver1.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Applications The following diagram shows a SWE-8 in a multi-zone application. SWE-8 in a Multi-Zone Application Operations Guide – DOC.
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 Specifications Specifications for the SWE-8 are listed in the following table.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone SWE-8 Specifications (Continued) SPECIFICATION DETAILS Power Requirements Power Pack 2 Amps @ 24 Volts DC 100-240 Volts AC, 50/60 Hz; power pack included Environmental Temperature 41º to 104º F (5º to 40º C) Humidity 10% to 90% RH (non-condensing) Heat Dissipation 41 BTU/Hr Enclosure Chassis Metal with black finish, vented sides Front Panel Metal with black finish and polycarbonate label overlay Mounting Freestanding or 1U 19
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 Physical Description This section provides information on the connections, controls and indicators available on your SWE-8. SWE-8 Physical View (Front) SWE-8 Physical View (Rear) SWE-8 Overall Dimensions 10.19 in (259 mm) 17.30 in (440 mm) 19.00 in (483 mm) 1.72 in (44 mm) 1 4 2 3 5 6 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone: SWE-8 6 7 Operations Guide – DOC.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Connectors, Controls & Indicators # CONNECTORS1, CONTROLS & INDICATORS 1 PWR LED 2 HW-R 3 ZONE (1-8) (Buttons and LEDs) 4 DIGITAL IN2 Green LED Pin 8 5 DESCRIPTION (1) Green LED indicates operating power supplied via power pack (1) Recessed push button for hardware reset Yellow LED (8) Push buttons and green LEDs, select output zone for routing and adjustment (1) 8-wire RJ-45 female (8P8C modular jack); Sonnex link input; Co
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS 6 24 VDC 2.0A (1) 2.1 mm barrel DC power jack; 24 Volt DC power input (power pack included) 7 GROUND (1) 6-32 screw, chassis ground lug DESCRIPTION 1. Interface connectors for SPEAKER OUTPUTS ports are provided with the unit. 2.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Setup Sonnex Link Wiring Crestron recommends using Crestron DM-CBL-8G (sold separately) or high-quality CAT5e shielded twisted-pair cable for Sonnex Link connections between the SWE-8 and the SWAMP-24X8 or S-EXT1-S. NOTE: Shielded connectors such as the DM-8G-CONN (sold separately) must be used. DM-CBL-8G wire can carry Sonnex Link signals up to 200 feet (61 meters).
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 To install the ears: 1. There are screws that secure each side of the SWE-8 top cover. Using a #1 or #2 Phillips screwdriver, remove the three screws closest to the front panel from one side of the unit. Refer to the diagram following step 3 for a detailed view. 2. Position a rack ear so that its mounting holes align with the holes vacated by the screws in step 2. 3.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone NOTE: To prevent overheating, do not operate this product in an area that exceeds the environmental temperature range listed in the table of specifications. Four balanced/unbalanced audio outputs are provided, utilizing 5-pin terminal block connectors. For connection details, refer to the following table and diagrams.
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 NOTE: The maximum cable length between a SWAMP-24X8 or S-EXT1-S and SWE-8 is 200 feet (61 meters). Label the Buttons Use Crestron Engraver software to print custom labels for the SWE-8’s front panel buttons and LEDs. Crestron recommends printing on 100-pound paper. Paper weighing less than 100 pounds tends to crumple while sliding in, while paper weighing more than 100 pounds may not fit.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Configuration The SWE-8 is automatically configured from the front panel of a connected SWAMP-24X8 or by Sonnex Tools software. For more information on configuration options, refer to the latest version of the SWAMP(I)-24X8 Sonnex Multiroom Audio System Operations Guide (Doc. 7049) which is available from the Crestron Web site (www.crestron.com/manuals). Operations Guide – DOC.
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron Web site. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at www.crestron.com/support. First-time users must establish a user account.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone The system tree of the control system displays the device in the appropriate slot(s) with a default Net ID or IP ID as shown in the following illustration. SWAMP-24X8 Device, Slots 8 and 9 3. Repeat step 2 for each SWE-8 to be added. NOTE: If using Cresnet for communications between the SWAMP-24x8 and a control system, only one SWE-8 expansion switcher can be connected.
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Establishing Communication All communication with the SWE-8 is managed through the communication link with a connected SWAMP-24X8.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Operation The SWE-8 operates in either Zone mode or Source mode. The SWE-8’s operating mode is determined by the operating mode of the SWAMP-24X8. For information on operating the SWAMP-24X8, refer to the latest version of the SWAMP(I)-24X8 Sonnex Multiroom Audio System Operations Guide (Doc. 7049). Zone Mode Zone mode uses the SWAMP-24X8’s front panel to route a source signal to a selected zone. To enter Zone mode: 1.
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. SWE-8 Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Audio dropouts heard on SWE-8 zone. Bad shield or no shield on Sonnex cable connecting SWAMP-24X8 and peripheral device.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Future Updates As Crestron improves functions, adds new features and extends the capabilities of the SWE-8, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron Web site periodically for manual update availability and its relevance.
Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone Crestron SWE-8 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron SWE-8 Sonnex™ Multiroom Audio Expansion Switcher, 8 Zone This page is intentionally left blank. Operations Guide – DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 7202A (2033120) 05.12 Specifications subject to change without notice.
