Crestron ST-CP SmarTouch™ Control Processor Contents SmarTouch™ Control Processor: ST-CP 1 Description................................................................................................................................. 1 Functional Description ................................................................................................ 1 Physical Description.................................................................................................... 2 Leading Specifications.......
Crestron ST-CP SmarTouch™ Control Processor SmarTouch™ Control Processor: ST-CP Description Functional Description The SmarTouch control processor, part of the SmarTouch STS/STSI, interfaces with almost all electronic equipment for complete control commands without delay. The control processor should be located in an area near the A/V equipment that needs to be controlled. It plays a vital role during programming and operation.
SmarTouch™ Control Processor Crestron ST-CP Physical Description The ST-CP, shown below, is housed in a black enclosure with silk-screened labels on the front and back of the case. On the front there are 10 LEDs for indicating the current status of the unit. All connections are made on the back of the unit. There are four rubber feet on the base of the unit for stability and to prevent slippage. ST-CP Physical Views 2 • SmarTouch™ Control Processor: ST-CP Operations Guide - DOC.
Crestron ST-CP SmarTouch™ Control Processor ST-CP Ports A number of ports are provided on the back of the ST-CP. Each has a silk-screened label. Refer to illustration and descriptions below. ST-CP Ports 12 VDC .5 A This DC power socket connector is used to supply power via an external AC power pack. Crestron recommends specific power packs for its devices. The recommended power pack for the ST-CP is Crestron part number PW-1205 (PWI-1210 for international use of the ST-CP/UK).
SmarTouch™ Control Processor Crestron ST-CP COM A - B These bi-directional 6-pin, 6-position RJ11 modular jacks are used to control additional audio/visual equipment via their RS-232 ports. Refer to the pinout table on the previous page. IR OUT A - D These 3.5mm mini phone jacks are used to control IR devices. Insert the mono mini plug of the STIRP and place the STIRP shell over the IR sensor window of the A/V equipment.
Crestron ST-CP SmarTouch™ Control Processor Leading Specifications The table below provides a summary of leading specifications for the ST-CP. Dimensions and weight are rounded to the nearest thousandth unit. Leading Specifications of the ST-CP SPECIFICATION Power Requirements DETAILS 12 or 24 VDC SIMPL™ Windows® Version 1.20.01 or later* VisionTools™ for Windows® Version 10.7 or later* VT Pro Version 1.1.7 or later* ST-CP Operating System Version 4.00.52s or later* ST-CP Monitor Version 1.
SmarTouch™ Control Processor Crestron ST-CP Typical Connection Diagram when Programming TOUCHPANEL NOTE: UNITS IN THIS ILLUSTRATION ARE NOT DRAWN TO SCALE. AC POWER PACK (CRESTRON MODEL OR EQUIVALENT) 15710 (PART OF ST-PK) PC 15717 (PART OF ST-PK) SERIAL PORT CONTROL SYSTEM USE ADAPTER (PART OF ST-PK) 1. Attach the RJ11 to DB9F adapter (15556, supplied with ST-PK) to one end of the PC to control processor cable (15717, supplied with ST-PK). 2.
Crestron ST-CP SmarTouch™ Control Processor Touchpanel to Control Processor Cable Operation When operating the ST-CP under normal conditions, refer to figure shown below for a typical connection diagram. Complete the following steps in the order provided to ensure proper connection of the system. It is assumed that the SmarTouch STS is currently connected for programming.
SmarTouch™ Control Processor Crestron ST-CP 3. Attach supplied antenna to BNC connector labeled RF on the back of the ST-CP. 4. Insert the mono mini plug of the STIRP into one of the four IR OUT ports of the ST-CP. Identifying the correct IR OUT port depends on the designations made when programming. In the illustration provided, it is assumed that the VCR is assigned to PORT A. Refer to the latest revision of the STIRP Installation Instructions (Doc.
Crestron ST-CP SmarTouch™ Control Processor ST-CP Troubleshooting (Continued) TROUBLE RF LED on ST-CP does not illuminate when trying to control A/V equipment. POSSIBLE CAUSE(S) CORRECTIVE ACTION Button on screen only Reopen project and verify that button join has internal functions number is between 1 and 999. (i.e., join number greater than or equal to 1000 or no join numbers, set to 0). ST-CP is not receiving power. RF transmitter in SmarTouch is faulty.
SmarTouch™ Control Processor Crestron ST-CP Software License Agreement This License Agreement (“Agreement”) is a legal contract between you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for software referenced in this guide, which includes computer software and, as applicable, associated media, printed materials, and “online” or electronic documentation (the “Software”).
Crestron ST-CP SmarTouch™ Control Processor If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity with Your valid licenses from Crestron of its authorized agent.
SmarTouch™ Control Processor Crestron ST-CP Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Crestron ST-CP SmarTouch™ Control Processor This page intentionally left blank. Operations Guide - DOC.
SmarTouch™ Control Processor Crestron ST-CP This page intentionally left blank. 14 • SmarTouch™ Control Processor: ST-CP Operations Guide - DOC.
Crestron ST-CP SmarTouch™ Control Processor This page intentionally left blank. Operations Guide - DOC.
