CRESTRON Contents Slide Controller: SP-SC Description Functional Description Physical Description Specifications Setup SP-SC with SmartPresenter™ SP-SC with SmarTouch™ ST-CP SP-SC with CNMSX Programming SmartPresenter™ SP-1 SmarTouch™ ST-CP CNMSX Problem Solving Troubleshooting Further Inquiries Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty Operations Guide - DOC.
CRESTRON Slide Controller: SP-SC Description Functional Description The SP-SC is a slide controller that allows easy control of slide projectors from the SmartPresenter, Smartouch ST-CP, and CNMSX systems. Physical Description The SP-SC is a small unit with a permanently attached 6 ft. (183 cm) projector cable. The projector cable is equipped with an EBY, pickle type connector. A 3ft. (91 cm) Serial Data Cable is supplied for connection to the SmartPresenter or the SmarTouch ST-CP systems.
CRESTRON Specifications Dimensions: Length Width Height 4.850" (123.19 mm) 1.324" (33.63 mm) 1.052" (26.72 mm) 6.2 oz. (176 g) Projector Cable: Connector Type Length EBY, Five-pin, Pickle 6' (183 cm) Serial Data Cable¹: Connector Type Length 3.5 mm, Straight, Stereo 3' (91.44 cm) Weight: Serial Data Cable²: Crestron p/n CNSP-112 12v DC Power Supply*: Crestron p/n PW-1205 (USA and Canada) Input 120V 60Hz 18W Output 12vDC 0.
CRESTRON Setup SP-SC with SmartPresenter™ Connect the 3.5 mm, Serial Data Cable (supplied) to the input port on the SP-SC. Connect the other end of the cable to one of the outputs on the SP-1. The EBY, fivepin, pickle type connector should be plugged into the projector. To assign a Q-Code for the Slide Controller, refer to the latest revision of the SmartPresenter – Quick Guide (DOC. 5742). NOTE: An external power supply is not necessary when using the SP-SC with the SmartPresenter system.
CRESTRON SP-SC with SmarTouch™ ST-CP Connect the 3.5 mm, Serial Data Cable (supplied) to the input port on the SP-SC. Connect the other end of the cable to one of the outputs on the ST-CP. The EBY, five-pin, pickle type connector should be plugged into the projector. To program the ST-CP for the Slide Controller, refer to the SmarTouch STS Wizard included with VisionTools Pro™ or Crestron's SIMPL™ Windows® programming software (v 1.20.04 or later) and the latest version of the Crestron Database (v 11.7.
CRESTRON SP-SC with CNMSX The SP-SC can be used with a variety of Crestron systems, including the CNMSX. When used with a CNMSX there are additional hardware requirements. • A specially designed Serial Data Cable is required (p/n CNSP-112). • An external power supply is required. Refer to "Specifications" on page 2 for part number and input/output voltage specifications. Connect the stereo plug of the CNSP-112 into the input port of the SP-SC.
CRESTRON Programming SmartPresenter™ SP-1 The SmartPresenter is field programmable and does not require a PC. Refer to the latest revision of the SmartPresenter – Quick Guide (DOC. 5742). SmartPresenter software is available, however, it is only necessary for changing drivers, cloning SP-1 machines, and updating firmware. SmarTouch™ ST-CP The SmarTouch systems are easily programmed using the SmarTouch STS Wizard. In several easy steps a SmarTouch system can be programmed and up-loaded.
CRESTRON Problem Solving Troubleshooting TROUBLE SP-SC not functioning. POSSIBLE CAUSE(S) SmartPresenter Q-Code incorrect SmarTouch ST-CP /CMMSX Incorrect Driver Selected No 12v power supply CORRECTIVE ACTION Verify that the correct Q-Code for the device has been assigned. Select the correct driver from the Crestron database. 12v power supply must be used (see "Specifications" on page 2).
CRESTRON Return and Warranty Policies Merchandise Returns / Repair Service 1. 2. 3. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address.
