System information

SIMPL+: 'Total Memory Used' is no longer displayed after compilation (Total NVRAM is still calculated & displayed)
Viewport: Fixed crash when opening "Set CS IP Info" dialog with no connection established.
Viewport: Added support for e-Control 2 on an ENET+.
Viewport: Fixed problem when trying to send a panel/firmware to incorrect (unassigned) ID.
Viewport: Added program advisor support to verify NVRAM requirements are met in control system.
Viewport: Fixed problem uploading firmware (Monitor) to pre-2-series systems.
Viewport: More reliable transfers all around (especially web pages to ENET+).
Viewport: Removed single-file size limit on web page uploads to ENET+ because of new firmware.
Viewport: Fixed OPS upload to CNMS (and similar) processors.
Viewport: Fixed bug where Ethernet program uploads to 2-series processors could flag the error light. Tcp/Ip
reconnections are now initiated by the remote side.
Viewport: Restored program load output on ethernet uploads of 2-series projects.
Viewport: Fixed intermittent problems with using "Functions/Set Network ID" with CNMS-style processors.
Viewport: Changed "File Transfer/Update Touchpanel Firmware" to "File Transfer/Update Touchpanel/Keypad
Firmware".
Viewport: Fixed error with "File Transfer/Get Mailbox..." on MSX.
Viewport: Fixed false error condition when performing a "Configure IP" on a CEN-CN whose TCP stack had not
previously been configured.
Viewport: Fixed problem where 2-series program files wouldn't go to the right directory.
Viewport: Resolved problems when working with a TSID of the form xFxxxxxx.
Viewport: Added support for new-style 2-series IP Table.
Viewport: Added new "Configure Ethernet" dialog with DHCP, IP Address and other ethernet options for 2-series
systems.
Viewport: Fixed bug in CNXTA dialog where "Hide Unused Slots" could be selected and slots would still be shown.
Viewport: Added 7-digit, purely numeric serial number as a valid form for TSID/Serial conversions.
Viewport: Fixed IP Table support for TPS panels.
Viewport: Fixed error where some valid IP addresses in Configure Ethernet dialog were being rejected.
Fixes/Changes from 2.03.17 to 2.03.18 - PUBLIC FTP SITE RELEASE:
Viewport: Fixed problems updating firmware over RS-232 to direct-connected TPS panels (introduced in Viewport
3.15)
Viewport: Fixed problem with X-Gen version advisor warning even when UPZ was adequate (introduced in Viewport
3.15)
Viewport: Fixed timing issue introduced when sometimes exiting passto and starting a new action.
Viewport: Fixed problem with Status messages not being drawn to screen properly (introduced in Viewport 3.10)
Fixes/Changes from 2.03.16 to 2.03.17:
Viewport: Reduced querying of rack type and 2-series control system information during several viewport
operations.
Viewport: Speed up Touch-Settable ID Operation through reduction of info-querying.
Viewport: Fixed crash when opening Configure ControlSys IP dialog in viewport.
Viewport: Fixed bug where cancelling a touchpanel transfer thru a 2-series would return success.
Implement C2N-MMS Model (without Scan Converter card). Also available in Library Update 200 or later.
Fix for App Builder where IR ports would show names like "Port AA", "Port BB", etc.
Fixes/Changes from 2.03.15 to 2.03.16:
Fix completeness check on CLX lighting modules.
Viewport: "Connecting..." dialog appears if TCP connection takes >3 seconds to be established.
Viewport: Fixed a bug where "EControl2" dialog would not give proper status info if the Control Systems EControl2
trial has not yet been started.
Viewport: Change DVP4 program load to reboot the system after the load is complete.
Viewport: Fixed intermittent bug when opening the viewport dialog if a connection failed could sometimes cause a
crash.
Viewport: Fixed bug where transmitter ID of 0 was not being printed in Dialog.
Viewport: Improved efficiency of Rack finding algorithm.
Viewport: Fixed bug where Options/FindRack could fail if AutoBaudSearch was not enabled.
Viewport: First release of Touch Settable ID functionality.