System information

Simpl Windows: Fixed system crash when trying to compile a program that had an empty (i.e. no symbols) module
nested within another module.
Viewport: Fixed a bug in the ethernet dialog where selecting LAN B would clear any DHCP or WINS settings (check
boxes also if either of them were enabled on the control system, when the dilog pops up the check boxes for those
items would not be checked.
Viewport: Fixed a bug where if connected securely, under certain conditions (updating a touch panel firmware) it
may not re-connect to the control system properly. It would fail with a dialog msg "Write error".
Viewport: Fixed bugs in sending NVRAM files.
Fixes/Changes from 2.04.14.01 to 2.04.14.02 :
SIMPL Windows: Fixed installation problem.
Library Update: Fixed issue with Serial Drivers on QM-RMC not displaying correctly. There is a new input called
[RESERVED]. This input should not be used and will be removed in later versions of SIMPL Windows. (Also
available in Library Update 236 and later).
Viewport: Version 3.56 - fixed several bugs with the DLL call vptSendMailboxDef where it would not use the proper
connection parameters. There was also a bug with error reporting if the file was overwritten.
Fixes/Changes from 2.04.14 to 2.04.14.01:
SIMPL Windows: Fixed issue with not being able to comment/uncomment symbols in the Program Manager program
tree.
SIMPL Windows: Fixed Simpl Windows crash when compiling a program with a module whose disk file could not be
located.
Fixes/Changes from 2.04.13 to 2.04.14 - PUBLIC FTP SITE RELEASE:
SIMPL+: Fix issue when compiling programs that have SIMPL+ components on network drives. An error message
"An Unnamed file could not be accessed" would sometimes pop up and cause the compile to be aborted. Library
Update: Correct 2 Series compilation of the CNWM-8 panel so that "Update Request" messages are not
continuously generated by the CNWM-8 (Also in Library Update 230 and later).
Library Update: Finish support for "Ethernet Offline Manager" which can be dropped as a device extender on the
following ethernet devices (ONLY IN A 2 SERIES PROGRAM): - CEN-IO, CEN-COM, CEN-CN, Virtual
Communications Port, e-Server (OEM), Ethernet Intersystem Communications, CEN-TVAV (Remote & Mixed
Processing), TPS-5000/6000/TPI w/TPS-ENET, all 2 Series Slave models. (Also available in Library Update 231
and later).
Library Update: Change order of signals for on the "DAP8 Analog Audio Switch". The inputs used to be CAT5_Src,
DSP/OutB_Src, OutA_Src. They are now OutA_Src, DSP/OutB_Src, CAT5_Src. The DAP8 firmware always
recognized the first input as OutA_Src and the third input as CAT5_Src (Also available in Library Update 231 and
later).
Library Update: Prevent C2N-DAP8 and C2N-DAP8RC from dropping on X Generation control systems (Also
available in Library Update 232 and later).
SIMPL Windows: Fixed Replace Control System Issues:
Incorrect serial drivers were sometimes being used when replacing one COM card with another.
A Remote Processing Module was being added to the Cresnet unnecessarily.
Replacing a CNX-DVP4 with a C2N-DVP4DI wasn't copying over the C2I-TPS symbol nor it's Device Extender
symbols appropriately.
Replace control systme logic will not allow a Remote Processing Module to be added to the new program just
to support moving over one of the devices. Note: if a Remote control system is a part of the original program,
it will be moved over.
Fixed problem where some Device Extender symbols were not getting moved to the new program. If a Device
Extender exists in the original program and is not allowed on the new control system, the symbol will still be
moved over but will be commented out such that programming will not be lost. However, the user will not be
allowed to uncomment out these symbols, they will only be able to copy the program to something else
and/or delete the symbol.
Fixed problem with moving over devices that are part of a 'group' of devices (such as the '3 Low Voltage
Relays' from the crestron database) and not maintaining knowledge of which devices were supposed to be
grouped together.
SIMPL Windows: Added a test at Program open to tell user if a Resynch may be required.
SIMPL Windows: Fixed problem with not being able to access Crestron IR files larger than 10k