System information
SIMPL Windows: Add proper device extenders to CN-TVAV Remote Processing, C2N-DAP8, C2N-DAP8RC, and
C2VEQ-4 (Also in library update 251 and later).
Viewport: Correct issue where the last digit of an IP Address would get cut off if all octets used a full 3 digits (i.e.
132.149.112.224 would get treated as 132.149.112.22). This problem only existed in Viewport 3.69.
SIMPL Windows: Fixed problem with Save As dialog being displayed when user cancels out of the "Enter Password"
dialog.
SIMPL Windows: Added Undo support for: typing over a signal name, changing a parameter value, changing
device/folder/symbol comments, using F9 to search/replace, commenting out symbols, commenting out signals,
moving Logic symbols or folders around under the Logic node.
Fixes/Changes from 2.05.10 to 2.05.11:
SIMPL Windows: Fix crash when trying to access IP ID config dialog for non-2 Series control system.
SIMPL Windows: Updated Module Header Dialog's Advanced Tab to now ask for Device Family and the Device
Type associated with the family. It will be the selection of both Device Family and Device Type that will used to
determine if there are any Standard Commands that can be included into the program.
SIMPL Windows: Updated Digital Input Properties dialog to now show the selected Device Family and Device Type
for the current module (if such selections exist) and to obtain the list of Standard Commands using both the Device
Family and Device Type.
Viewport: Fixed a problem with the modem connection feature. When you exited the viewport and stayed
connected, and when you later entered the viewport or other software (i.e. Test Manager), the control system
would not respond even though you are still connected. The "+++" when viewport exits was being echoed and put
the remote modem into command mode. This is a 2 Series only issue.
Fixes/Changes from 2.05.09 to 2.05.10:
Viewport: Fixed a bug where viewport would not find an 2 Way Gateway (i.e. STRFGWX) when it really was there
when connected to an X-gen system and was is the last device listed.
Viewport: XM Radio support for ID Dialog.
Viewport: Changed compacting timeout for touch panels to 15 minutes from 6 minutes
Viewport: When sending a SIMPL program to a 2 Series system, if the program requires more NVRAM than is
available becuase there is an NVRAM disk allocated, prompt the user to erase the disk to allow the program to fit. If
it won't fit even without the NVRAM disk, it will fail without prompting. SIMPL+: Implement function
WaitForInitialization(). This can only be used in function Main() and is used to suspend the SIMPL+ module until the
first logic solution has been run, which will guarantee that inputs to the SIMPL+ module that occur at startup have
been propagated and have the correct value when reading them. Requires CUZ 3.086 or later; 2 Series only.
SIMPL Windows: Fixed problem where a signal was being duplicated in the program (i.e. 2 instances of same
named signal) if an Undo was performed previously.
SIMPL Windows: Added UNDO for appending Suffix or Prefix in the Detail View.
SIMPL Windows: Added display of errors if pasting a symbol from the clipboard and not everything below it could be
pasted.
SIMPL Windows: Fixed problem where, if the F4 function was used in Detail View to autoincrement a signal name,
and an existing signal was part of the selection but there was no signal to start autonaming from, the existing signal
was being deleted. F4 will no longer delete signals if no autoincrementing was implemented.
SIMPL Windows: Added logic such that IR and Serial drivers cannot be stacked on the same port. Also, only 1
serial driver will be allowed on an IR port.
SIMPL Windows: Added logic to the Resync process that will now disconnect signals from any cue that has been re-
labeled as [~UNUSED~]
SIMPL Windows: Fixed issue with pdf help files for symbols. If user defines a file then removes that from the module
header, the system was still looking for the pdf file whenever Help was requested.
SIMPL Windows: Fixed problem with incorrect symbols being added to a program when replacing something like a
VEQ4 with a COM card.
SIMPL Windows: Fixed problem when replacing an Ethernet InterSystem Communication device with an Ethernet
InterSystem Communication with RCB device. The analog input signals were being transferred over to the wrong
input cues. Note that the RCB device is not currently released.
SIMPL Windows: Fix issue when converting QM-RMC to another 2 Series system where the digital output trigger
signal names would get lost (Also in library update 250 and later).
SIMPL Windows: Make UDP/IP device visible. Requires CUZ 3.037 or later. (Also in library update 249 and later).
Fixes/Changes from 2.05.08 to 2.05.09: