System information

Add "Annotation Reserved Joins" to the following panels (No help available yet)
TPS-12G-QM (Cresnet, Ethernet)
TPS-15G-QM (Cresnet, Ethernet)
TPS-G-TPI (Cresnet, Ethernet)
Add backchannel support for SMART screen for TPS-G-TPI (Cresnet/Ethernet)
Fix Power factor & HelpID for CLS-C6/CLS-C6M Scenes slot.
Fixes/Changes from 2.07.27 to 2.07.28:
Fixed compilation issue that caused "//" on the input side of some symbols to behave incorrectly (noted ones are on
String I/O, IR Ports, Serial Inputs to Macros, and using it on the RESET of a Stepper2. There are others that have
not been reported, but revised algorithms should take care of them). This affects both X Generation (and below)
and 2 Series compilers.
SIMPL Windows: Will now save the Limited Symbol Mode (2nd to last toolbar icon). When this button is enabled,
Simpl Windows will count the current number of symbols in the Detail View window. As long as this button is
enabled, that many symbols will be the maximum amount of symbols to be displayed in the Detail View at any one
time. If more than this maximum number of symbols are selected for viewing, the first symbol to have been selected
for display will be closed (i.e. First In First Out).
SIMPL Windows: Changed the default Auto Tile mode to now be Auto Tile Horizontal (selectable via the View
menu). When displaying the symbols in the Detail View in Horizontal Tile mode, there is more of a chance of being
able to read the full cue and Input/Output signal names.
Fixes/Changes from 2.07.26 to 2.07.27:
SIMPL Windows: Fixed error in Replace Control system when performed via the Control System view pane. If the
control system has default logic associated with it, the associated default logic module was getting added twice.
SIMPL Windows: Fixed the Auto increment last (F4) function in Detail view when dealing with "//" signals. Simpl will
now automatically try to determine the type or prompt the user for the type. Previously, if the cue type didn't match,
that cue was not connected to a "//" signal.
SIMPL Windows: Fixed error on Preferences->Program Editing page where the radio buttons for the Special
Symbol set were not reflecting the correct selection.
SIMPL Windows: Replaced the key sequence Ctl+Shift on the Program Tree and the System Configuration tree, to
F11. This key will toggle the dipsplay of data that is meaningless to the programmer, and harmless to display, but
can be used by Crestron support personnel for problem resolution.
Fixes/Changes from 2.07.25 to 2.07.26:
SIMPL Windows: CTL+W will now be the keyboard shortcut for toggling between Configuration Manager and
Program Manager views. This resolves the issue introduced in 2.07.24 where Ctl+Tab was no longer effective in
switching between symbols in the Detail View because Ctl+Tab had been remapped to switch between
configuration manager and program views in 2.07.24.
Simpl Windows: Fixed a potential Data Integrity problem that could occur from adding devices with default logic and
then deleting those devices before having saved the project.
SIMPL Windows: Changed wording on Compile Statistics dialog if an AES is being compiled. The previous message
made it appear as though a transfer to control system had been attempted and failed. The intent of the original text
("Cannot Transfer!") was to tell the program that transferring the project via Simpl Windows was not possible and
as such, the programmer should use the Cresetron Toolbox. New text now reads: "Note: The Viewport software
does not support this control system. To transfer this project to the control system please use the Crestron Toolbox
for interfacing to this device."
SIMPL Windows: Fixed problem with Alt+F5 not inserting a "//" signal in detail view
SIMPL Windows: Fixed issue with Error Log getting cleared before doing a Drag and Drop of Signals in Detail View.
Simpl+: Removed Parameter text from default template file.
Removed firmware requirements for _SKIP_, #OUTPUT_SHIFT, #DIGITAL_EXPAND and #ANALOG_EXPAND.
Fixes/Changes from 2.07.24 to 2.07.25:
SIMPL Windows: Changed Detail View context menu option of "Comment out/Remove Comment on Input/Output" to now
read as "Insert/Remove special "//" signal."