Crestron MPC-M5 MPC Media Presentation Controller™ M5 Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Crestron MPC-M5 Media Presentation Controller™ M5 Contents MPC Media Presentation Controller™ M5: MPC-M5 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications.................................................................................................................
Media Presentation Controller™ M5 Crestron MPC-M5 MPC Media Presentation Controller™ M5: MPC-M5 Introduction Creston® MPC Media Presentation Controller™ is a family of 2-Series control systems designed for installation in a wall or podium, delivering the industry’s best multimedia room control technology in a convenient, space saving design.
Media Presentation Controller™ M5 Crestron MPC-M5 Control…Simplified The MPC-M5 is engineered to be easy to integrate and use, yet versatile enough to suit each application perfectly. Its ten “hard key” buttons can be freely programmed for system power, input source selection, transport control, volume adjustment, lighting presets and any other functions. Custom backlit labeling of the buttons is facilitated using an assortment of pre-printed labels or Crestron Engraver software.
Media Presentation Controller™ M5 Crestron MPC-M5 Applications The following diagram shows an MPC-M5 in a commercial application. MPC-M5 in a Commercial Application Operations & Installation Guide – DOC.
Media Presentation Controller™ M5 Crestron MPC-M5 Specifications Specifications for the MPC-M5 are listed in the following table.
Media Presentation Controller™ M5 Crestron MPC-M5 MPC-M5 Specifications (Continued) SPECIFICATION DETAILS Available Models MPC-M5-B-T MPC Media Presentation Controller M5, black MPC-M5-W MPC Media Presentation Controller M5, white Available Accessories CEN-SW-POE-5 5-Port PoE Switch CNSP-XX Custom Serial Interface Cable GLS Series Crestron Green Light Occupancy Sensors IRP2 IR Emitter Probe MP/MPC/IPAC_FRONT_LABEL [BLANK, ENGRAVED]-B-T Set of custom engravable backlit labels, white on blac
Media Presentation Controller™ M5 Crestron MPC-M5 Physical Description This section provides information on the connections, controls and indicators available on your MPC-M5. MPC-M5 Physical View (Front) MPC-M5 Physical View (Rear) 6 Media Presentation Controller™ M5: MPC-M5 Operations & Installation Guide – DOC.
Media Presentation Controller™ M5 Crestron MPC-M5 MPC-M5 Overall Dimensions (Front View) 1 2 4.50 in (115 mm) 3 4 2 5 3 6 6.10 in (155 mm) MPC-M5 Overall Dimensions (Rear and Side Views) 3.55 in (91 mm) 7 0.52 in (14 mm) 7 2.00 in (51 mm) 8 9 Operations & Installation Guide – DOC. 6955B 10 11 1.
Media Presentation Controller™ M5 Crestron MPC-M5 Connectors, Controls & Indicators # CONNECTORS, CONTROLS & INDICATORS 1 IR RECEIVER Receives signals from IR transmitter 2 FEEDBACK INDICATORS (10) Programmable red LEDs (one per hard key) 3 HARD KEYS (10) Programmable buttons with backlit labeling 4 COMPUTER Pin 1 Pin 4 Pin 2 Pin 3 DESCRIPTION (1) USB Type B female (behind front cover); USB 1.
Media Presentation Controller™ M5 Crestron MPC-M5 Connectors, Controls & Indicators (Continued) # CONNECTORS, CONTROLS & INDICATORS 10 RELAYS 1-2 DESCRIPTION (4) Captive screw terminals comprising (2) normally open, isolated relays Rated 1 Amp, 30 Volts AC/DC MOV arc suppression across contacts PIN 11 I/O DESCRIPTION 1 1 2 Common 3 2 4 Common (4) Captive screw terminals comprising (2) contact closure or voltage sensing inputs (referenced to ground) with 24 Volt DC power output Input volt
Media Presentation Controller™ M5 Crestron MPC-M5 Setup Network Wiring When wiring the Ethernet network, consider the following: Use Crestron power supplies for Crestron equipment. Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (www.crestron.com/calculators).
Media Presentation Controller™ M5 Crestron MPC-M5 Installation The following material and tools are required for installation of an MPC-M5: Standard 2-gang electrical box (not included) Philips screwdriver 1/16” Allen wrench (included) After the wiring has been installed and verified, use the following procedure to install the MPC-M5 in a standard, 2-gang electrical box. 1. Turn system power OFF. 2.
Media Presentation Controller™ M5 Crestron MPC-M5 Attach the MPC-M5 Button Labels Screws (2) 04-40 x 1/4" (2007156) Label Holder 6. Attach the label holder by placing it over its slots and sliding it downward into position. 7. Attach the included labels in the appropriate positions on the MPC-M5. 8. Perform any necessary programming using the COMPUTER (USB) connection prior to attaching the front panel of the MPC-M5. (Programming can also be performed via the LAN port.) 9.
Media Presentation Controller™ M5 Crestron MPC-M5 Hardware Hookup Connect the Device Make the necessary connections as called out in the illustrations that follow. Refer to “Network Wiring” on page 10 before attaching the LAN PoE connector. Apply power after all connections have been made. When making connections to the MPC-M5, use Creston power supplies for Crestron equipment.
Media Presentation Controller™ M5 Crestron MPC-M5 Hardware Connections for the MPC-M5 (Rear View) LAN: 10/100BASE-T Ethernet to LAN or Web COM: To Any 3-Wire RS-232 Device IR: To IRP2 or Serial Devices Input Connections RELAYS: To Controllable Devices I/O: Inputs From Digital Devices (and 24 Volt Power For Sensors) Depending on the application, the MPC-M5 inputs can be wired two ways. Refer to the diagrams on the following page when wiring inputs. CAUTION: Incorrect wiring may damage the MPC-M5.
Media Presentation Controller™ M5 Crestron MPC-M5 Input Wiring Diagrams Detecting a contact closure from a switch or relay Detecting a floating contact voltage (e.g.
Media Presentation Controller™ M5 Crestron MPC-M5 Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron Web site. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at http://support.crestron.com. First-time users will need to establish a user account.
Media Presentation Controller™ M5 Crestron MPC-M5 Locating the MPC-M5 in the Device Library Program Manager is the view where programmers “program” a Crestron control system by assigning signals to symbols. Program Manager The symbol can be viewed by double clicking on the icon or dragging it into Detail View. Each signal in the symbol is described in the SIMPL Windows help file (F1).
Media Presentation Controller™ M5 Crestron MPC-M5 Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system (and/or device).
Media Presentation Controller™ M5 Crestron MPC-M5 TCP/IP Ethernet Communications (Without Hub or Router) Ethernet PC Running Crestron Toolbox Power Injector PoE MPC-M5 120 V The MPC-M5 connects to PC via Ethernet: 1. Establish USB communication between MPC-M5 and PC. 2. Enter the IP address, IP mask and default router of the MPC-M5 via the Crestron Toolbox (Functions | Ethernet Addressing); otherwise enable DHCP.
Media Presentation Controller™ M5 Crestron MPC-M5 Programs and Firmware Program or firmware files may be distributed from programmers to installers or from Crestron to dealers. Firmware upgrades are available from the Crestron Web site as new features are developed after product releases. One has the option to upload programs via the programming software or to upload and upgrade via the Crestron Toolbox.
Media Presentation Controller™ M5 Crestron MPC-M5 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. MPC-M5 Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Unexpected response from control system. Network devices are not communicating with the control system. Use Crestron Toolbox to poll the network.
Media Presentation Controller™ M5 Crestron MPC-M5 System Monitor The System Monitor allows you to reload firmware into the MPC-M5 in the event that you cannot load the firmware in the normal mode. If the system does not function, perform the following procedure: 1. Disconnect all Crestron USB devices from the computer. 2. On the MPC-M5, press and release the HW-R button. 3. Press and release the SW-R button three times. 4. Connect to the PC using a USB cable.
Media Presentation Controller™ M5 Crestron MPC-M5 Reference Documents The latest version of all documents mentioned within the guide can be obtained from the Crestron Web site (www.crestron.com/manuals). This link will provide a list of product manuals arranged in alphabetical order by model number.
Media Presentation Controller™ M5 Crestron MPC-M5 Software License Agreement This License Agreement (“Agreement”) is a legal contract between you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for software referenced in this guide, which includes computer software and as applicable, associated media, printed materials and “online” or electronic documentation (the “Software”).
Media Presentation Controller™ M5 Crestron MPC-M5 If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity with Your valid licenses from Crestron of its authorized agent.
Media Presentation Controller™ M5 Crestron MPC-M5 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Media Presentation Controller™ M5 Crestron MPC-M5 This page is intentionally left blank. Operations & Installation Guide – DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 6955B (2027069) 10.10 Specifications subject to change without notice.
