Crestron IRP2 Infrared Emitter Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2004 Crestron Electronics, Inc.
Crestron IRP2 Infrared Emitter Contents Infrared Emitter: IRP2 1 Introduction..............................................................1 Description.......................................................1 Package Contents .............................................2 Installation................................................................2 Attach the IRP2 to the IR Sensor Window ......2 IR Mask Installation.........................................3 Attach the IRP2 to Other Locations............
Crestron IRP2 Infrared Emitter Infrared Emitter: IRP2 Introduction The IRP2 is an infrared emitter housed in a plastic shell. The IRP2 shell emits IR control signals sent to it by a Crestron® control system. The IRP2 shell can be installed directly on the IR sensor window of the controlled device or at a nearby suitable location. The IRP2 is compatible with 2-Series controllers. It is also compatible with X-Generation controllers by exchanging the 3.5 mm connector for a 5 mm connector (not supplied).
Infrared Emitter Crestron IRP2 Package Contents In addition to the IRP2, this package also contains an IR mask and twosided transparent tape. Installation Attach the IRP2 to the IR Sensor Window Refer to the following instructions and illustration. 1. Identify the clear, flat bottom surface of the IRP2 shell. 2. Apply transparent silicon adhesive (not supplied) to the flat side of the IRP2 or use the supplied transparent tape.
Crestron IRP2 Infrared Emitter IR Mask Installation The IR mask (supplied) is designed to fit over the IRP2 shell, as shown in the following illustration, so that the sensor window of the controlled component is completely covered. The IR mask prevents unwanted external IR signals from passing through or leaking past it. The IR mask also prevents emitting IR from the IRP2 shell from radiating backward into the IR sensors of other nearby components. 1.
Infrared Emitter Crestron IRP2 shell permits control at this greater distance. Placement of the IRP2 on surfaces just above or below the IR sensor window, as shown in the following illustrations, may provide a more pleasing aesthetic appearance. However, be sure to position the IRP2 shell so that the edge of the component does not block the IR signal. NOTE: Placing the IRP2 shell on a cabinet door may result in interruption of the IR signal if the door is opened.
Crestron IRP2 Infrared Emitter NOTE: The white-traced wire connects to the pin labeled S. Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron’s award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (http://www.crestron.com) for a listing of Crestron worldwide offices.
Infrared Emitter Crestron IRP2 As of the date of manufacture, the IRP2 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Crestron IRP2 Infrared Emitter Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Installation Guide – DOC. 8168A 12.04 Specifications subject to change without notice.