Specifications

6
quickstart guide
GL-IPAC-SW8
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
GL-IPAC-SW8
Crestron Green Light
®
Integrated Switching System
The following screens allow configuration of the date, time, and
daylight savings settings.
Press Next from the “System Setup” screen to advance to the “Set
Current Date” screen.
On the “Set Current Date” screen use the up and down buttons to
change the month, date, and year. Press ENTER to to move between
the date and year. Press Next to advance to the “Set Current Time”
screen.
Press Edit on the “Set Current Time” screen to change the time. Use
the up and down buttons to change the values and ENTER to move
between the hour, minute, second, and AM/PM. Press Set to save
the values.
Press Next to advance to the “Daylight Savings Time” screen. Using
the up and down buttons select Off or Auto. Off turns daylight savings
time off and Auto updates the time based on daylight savings time for
the region.
Press ENTER to make the selection and Exit to save the settings and
return to the “Setup” menu.
Next
Set Current Date
[10] – 20 – 2013
Edit Next
Set Current Time
4 : 21 : 08 PM
Next
Daylight Savings Time
Off
Auto
SelectExit
For Regulatory Compliance information, refer to Doc. 7401.
QUICKSTART DOC. 7389B (2036222, Sheet 3 of 7) 01.14
Follow the procedures below to set up the GL-IPAC-SW8.
4
Setup
Use the front panel controls and display to configure the
GL-IPAC-SW8. The following controls are used to navigate the front
panel display: up arrow, down arrow, ENTER, HOME, BACK,
CANCEL, and HELP. There are four soft buttons which perform the
functions listed above them on the front panel display screen.
From the home screen on the front panel display, press Setup to
access the full list of options for configuring the GL-IPAC-SW8. Press
the HELP button while on any setup screen to display additional setup
information.
If timeclock events need to be changed after the GL-IPAC-SW8 is fully
configured, press TmClk to add, edit, or remove timeclock events. The
TmClk button enters the timeclock procedure starting on page 11.
“Setup” Menu
After pressing Setup, a list of 10 configuration options appears:
• Project Settings sets the geographical location of the
GL-IPAC-SW8 installation as well as the time, date, and daylight
savings settings.
• Panels configures the additional lighting panels controlled by the
GL-IPAC-SW8.
• Occupancy Sensors configures the occupancy sensors attached
to the GL-IPAC-SW8.
• Photo Sensors configures the photo sensors attached to the
GL-IPAC-SW8.
• Keypads configures all keypads in the system.
• Remote Keypads configures keypads connected to external systems via IP.
• Contact Closures triggers specific actions using two pre-defined contact closure inputs and six custom contact closure inputs.
• Timeclock configures the timeclock.
• Ethernet Settings configures the Ethernet settings.
• About displays the GL-IPAC-SW8 information.
Project Settings: “Select State” Screen
Select Project Settings from the “Setup” menu to configure basic
GL-IPAC-SW8 settings.
Use the up and down buttons to highlight the nearest city then press
Next to advance to the “System Setup” screen.
Panels: “Load Count” Screen
Select Panels from the “Setup” menu to modify external panel lighting
loads. The “Load Count” screen identifies internal and external loads
on the GL-IPAC-SW8. The GL-IPAC-SW8 supplies eight circuits to
switch loads.
To change the number external loads, highlight EXT: --- -- and press
Edit. Use the up and down arrows to change the number of external
loads then press ENTER.
Edit Clear ID Exit
Int: 8 Loads
Ext: --- --
Load
Count
SelectEdit
(Continued on following page)
Panels
Project Settings
Setup
TmClk
V1.00.018
IPAC-SW8
4
:
21
PM
Select
Project Settings
Panels
Keypads
Timeclock
Setup
Select
Next
New Jersey
New Mexico
New York
North Carolina
Select
State
SelectNext