Specifications

11
quickstart guide
GL-IPAC-SW8
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
GL-IPAC-SW8
Crestron Green Light
®
Integrated Switching System
For Regulatory Compliance information, refer to Doc. 7401.
QUICKSTART DOC. 7389B (2036222, Sheet 6 of 7) 01.14
4
Setup: Contact Closures (Continued)
Timeclock: “Holiday List” Screen
NOTE: If using the TmClk button from the front screen proceed to
the last box in the next column of this page.
To program or adjust timeclock events on the GL-IPAC-SW8, select
Timeclock from the “Setup” menu or select the TmClk shortcut on
the home screen. The “Holiday List” screen provides a list of
holidays. A holiday is observed if the screen displays an “X” next to
the holiday.
Use the up and down arrows to highlight a setting and press Select
to observe or remove a holiday. Select - - - at the bottom of the list of
holidays and press Add to add a custom holiday. A total of 100
timeclock events can be added.
Timeclock: “Timeclock Warn Setup” Screen
The “Timeclock Warn Setup” screen schedules the lights to blink as a
warning before they turn off. The length of time that the warning lasts
and which loads perform the warning are set in the following screens.
Press Next to advance to the “Timeclock Warn Time” screen.
Use the up and down buttons to select the warn time (in minutes).
The selection can range from 1 to 30 minutes.
Press Next to advance to the “Warn Loads” screen and select the
loads that blink.
Contact Closures: “Select Loads” Screen
If a contact closure is set to on, off, toggle, or custom then the “Select
Loads” screen is displayed. On, Off, Toggle, and Custom each have
different operations that can be performed:
• On turns lights on or allows lights to turn on based upon photo
sensor light readouts.
• Off turns lights off with a warning that the lights are about to turn
off.
• Toggle operates with the functionality of the On and Off
mentioned above.
• Custom allows further modification of the above options.
Use the up and down arrows to highlight the desired load and press Adjust to change the contact closure settings.
Press Set All to select all loads and Clr All clears the functions of all loads.
Thanksgiving
Thksgvg 2 Day
Christmas
---
Add Next
Holiday
List
Next
Timeclock Warn Time
Warn Time: [5] minutes
SelectNext
Next
Timeclock Warn Setup
On the following pages set the
warn time and warning loads
Press Help for more info
Set All Clr All Adjust
L1.1 (p,o) = On
L1.2 (p,o) = - - -
L1.3 (o) = - - -
L1.4 (o) = - - -
Select
Loads
CC.3
OK
Timeclock
The “Time Clock Events” screen allows the start and end of the
workday to be adjusted. Events on weekdays, weekends, and
holidays can also be set.
NOTE: The TmClk button on the home screen enters the
procedure at this point.
Use the up and down buttons to highlight Start of Workday and
press Edit then use the up and down buttons to select the time and
ENTER to advance though the settings. Press Next to save and
exit. Repeat this process for End of Workday.
To add additional timeclock events, highlight - - - and press Add.
The Add option only appears when - - - is highlighted. Use the up
and down arrows and the ENTER button to select the days the
event should take place (weekdays, weekends, holidays, or custom) then press Next. Select Standard, Sunrise, or Sunset from
the following screen. Standard allows input of a fixed time. Sunrise and Sunset use the device’s astronomical clock to coordinate
the event with the sunrise or sunset (+/- 2 hours).
Press Next to advance to the “Event Type” screen. Use the up and down buttons and the ENTER button to select Lights On/Off,
Lock Keypads, or Unlock Keypads. Press Next if Lights On/Off is selected or Done if Lock Keypads or Unlock Keypads is
selected.
Press Exit to save settings and return to the “Setup” screen.
Edit
Start of Workday
End of Workday
1. Wkday SS+2:00
2. Wkly 2:10 PM
Clock
Time
Events
Exit
Use the up and down buttons to highlight the desired loads and
press Select to select the loads.
Press Set All to select all loads.
Press Clr All to deselect all loads
Press Next to configure the timeclock events.
Clr All
L1.1
L1.2
L1.3
L1.4
Warn
Loads
SelectSelectSet All Next
(Continued on following page)