Specifications

10
quickstart guide
GL-IPAC-SW8
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
GL-IPAC-SW8
Crestron Green Light
®
Integrated Switching System
For Regulatory Compliance information, refer to Doc. 7401.
QUICKSTART DOC. 7389B (2036222, Sheet 5 of 7) 01.14
4
Setup: Keypads (Continued)
Contact Closures: “Cont. Closures” Screen
Select Contact Closures from the “Setup” menu to show a list of the
six editable contact closures (CC3 - CC.8).
• Contact closure 1 is preprogrammed to lock the GL-IPAC-SW8.
• Contact closure 2 preprogrammed to lock all keypads in the
system.
• Contact closures 3 -8 (CC.3 -CC.8) can be programmed using
the same functions as the keypads, in addition to being able to
lock, unlock, and lock/unlock the GL-IPAC-SW8 or the keypads.
Use the up and down arrows to highlight a contact closure and then
press Edit to program the functions for the contact closures.
Contact Closures: “Select function” Screen
To edit the functions of a contact closure, select one from the “Select
function” screen: On, Off, Toggle, Custom, Enter Override, Exit
Override, Enter/Exit Override, Enable Timeclock, Disable Timeclock,
Enable/Disable Timeclock, Lock Keypads, Unlock Keypads,
Lock/Unlock Keypads, Lock GL-IPAC-SW8, Unlock GL-IPAC-SW8,
and Lock/Unlock GL-IPAC-SW8.
Press Next to edit the controlled loads if the selection was On, Off,
Toggle, or Custom.
Other selections navigate to the “Contact Closures” screen.
NOTE: Contact closures have maintained logic functionality.
Remote Keypads: “Rmte Keypd List” Screen
To program or edit remote keypads that operate with a connected
control system, select “Remote Keypads” from the “Setup” screen. The
GL-IPAC-SW8 allows for up to two remote keypads to be connected at
ID 20 and 21 on the remote control system.
Refer to the steps described in “Keypads” on page 9 to program button
functions for remote keypads.
Press Setup to configure the remote keypad on the “Keypad Address
Setting” screen.
Remote Keypads: “Keypad Address Setting” Setup
Configure the remote keypad by entering the IP address of the remote
control system. Press Edit and then use the up and down buttons to
change the IP values. Press ENTER to advance to the next part (octet)
of the IP address.
Press Set to confirm address. The GL-IPAC-SW8 must be restarted
after altering the IP address.
NOTE: After setting the IP address of the remote control system, an
EIC must be added to the remote system program. On the EIC, joins
200-219 are dedicated for the remote keypads.
Press Clear to delete the IP Address.
Press Exit to save the settings and return to the “Rmte Keypd List” screen.
Edit Exit
Keypad Address Setting
IP Address
127.000.000.001
Clear
Next
On
Off
Toggle
Custom
Select
funct
-ion
CC.3
SelectNext
Press Edit Setup
20: Not Programmed
21: Not Programmed
Rmte
Keypd
List
Exit
Edit
CC.3
CC.4
CC.5
CC.6
Cont.
Clos-
ures
Exit
Remote Keypads
Contact Closures
Keypads: “Select Loads” Screen
After assigning button functions to keypads either manually or
automatically, the “Select Loads” screen appears. If a button is set to
On, Off, Toggle, or Custom, the loads affected by the button press
must be selected. Affected loads have the function listed next to the
load ID. Unaffected loads have “- - -” next to the load ID.
Press Adjust to change functions.
Set All selects all loads.
Clr All clears the functions of all loads.
Keypads: “Select Btn Type” Screen
Assign a button function by selecting any of the following options: On,
Off, Toggle, Custom, Enter Override, Exit Override, Enter/Exit
Override, Enable Timeclock, Disable Timeclock, and Enable/Disable
Timeclock.
Select Next to assign loads to the button.
Keypads: “Select Btn” Screen
To manually program or edit a button’s function, select the button on
the “Select Btn” screen.
Press Edit to display functions.
Copy duplicates button functions and Paste adds the functions to
another button.
OK saves the button functions.
Next
Toggle
Custom
Enter Override
Exit Override
Select
Btn
Type
B1.3
SelectNext
Edit Copy Paste
Button 1
Button 2
Button 3
Button 4
Select
Btn
KP-1
OK
Set All Clr All Adjust
L1.1 (p,o) = On
L1.2 (p,o) = - - -
L1.3 (o) = - - -
L1.4 (o) = - - -
Select
Loads
B1.3
OK
(Continued on following page)