Installation guide

Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200
DM-RMC-200-S/DM-RMC-200-S2 Specifications (Continued)
SPECIFICATION DETAILS
Available Accessories
CBL Series Crestron Certified Interface Cables
CNSP-XX Custom Serial Interface Cable
CRESFIBER-CONN-
SC50UM-12
(DM-RMC-200-S only) CresFiber Fiber
Optic Cable Connector
CRESFIBER-SINGLE-SC
(DM-RMC-200-S only) CresFiber Simplex
Fiber Optic Cable Assembly, 50/125, SC
CRESFIBER-SINGLE-
SC-ARMORED
(DM-RMC-200-S only) CresFiber
ARMORED Simplex Fiber Optic Cable
Assembly, 50/125, SC
CRESFIBER-SINGLE-
SC-CLEAR
(DM-RMC-200-S only) CresFiber CLEAR
Simplex Fiber Optic Cable Assembly,
50/125, SC
CRESFIBER-SM-CONN-
LC-12
(DM-RMC-200-S2 only) CresFiber
Single-Mode Fiber Optic Cable
Connector
CRESFIBER-TK CresFiber Termination Kit
CRESFIBER8G
(DM-RMC-200-S only) CresFiber 8G
Fiber Optic Cable
CRESFIBER8G-SM
(DM-RMC-200-S2 only) CresFiber 8G
Single-Mode Fiber Optic Cable
IRP2 IR Emitter Probe
MP-WP Series Media Presentation Wall Plates
MPI-WP Series
Media Presentation Wall Plates –
International Version
1. Using the DMTool in Crestron Toolbox™, the scaler can be enabled/disabled.
2. Automatically passes 3D video if display device supports it (reverts to pass-through mode
without scaling). Provides automatic 3D to 2D conversion (with scaling) if display device does not
support 3D.
3. Video wall processing requires a separate DM receiver for each individual display.
4. For DM 8G wiring, the maximum DigitalMedia 8G fiber cable length is 1000 feet (~300 meters)
using CRESFIBER8G fiber optic cable, or 500 feet (~150 meters) using standard CRESFIBER,
CRESFIBER-SINGLE-SC, or generic OM3 simplex multimode fiber optic cable. For DM 8G SMF
wiring up to 7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic
G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron
DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. All wire and cables
sold separately.
5. HDMI requires an appropriate adapter or interface cable to accommodate a DVI signal.
CBL-HD-DVI interface cable sold separately.
6. With or without reduced blanking.
7. With reduced blanking only.
8. Using the DMTool in Crestron Toolbox, the amplifier can be enabled/disabled.
9. The latest software versions can be obtained from the Crestron Web site. Refer to the NOTE
following these footnotes.
10. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product
Catalog for a complete list of 2-Series control systems.
NOTE: Crestron software and any files on the Web site are for authorized Crestron
dealers and Crestron Authorized Independent Programmers (CAIPs) only. New users
may be required to register to obtain access to certain areas of the site (including the
FTP site).
Operations & Installation Guide – DOC. 7246B DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2  9