Specifications

DMPS-200-C DigitalMedia
™
Presentation System 200
crestron.com
|
800.237.2041
Wire Size: Terminals accept up to 14 AWG;
Output Power: 40W RMS mono at 70 or 100 Volts;
Note: 4Ω/8Ω and 70/100V outputs are mutually exclusive
PROG OUT: (1) 5-pin 3.5mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
AUX OUT 1 – 2: (2) 5-pin 3.5mm detachable terminal blocks;
Balanced/unbalanced stereo line-level audio outputs;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
HDMI OUTPUT 1: (1) 19-pin Type A HDMI female, digital video/
audio output;
Signal Types: HDMI, DVI
[1]
DM OUTPUT 2: (1) 8-pin RJ45 female, shielded;
DM 8G+ output, HDBaseT compliant;
PoDM and PoH PSE (Power Sourcing Equipment) port
[3]
;
Connects to DM 8G+ input of a DM receiver/room controller or other DM
device , or to a HDBaseT device, via CAT5e or Crestron DM-CBL-8G cable
[2]
Connectors - Control & Power
IR/SERIAL OUT 1 – 4: (4) 2-pin 3.5mm detachable terminal blocks;
IR/Serial output ports;
IR output up to 1.2 MHz;
1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
IR IN: (1) 3-pin 3.5mm detachable terminal block
For connection of the CNXRMIRD IR Receiver
[4]
;
Allows control from IR wireless remotes using RC-5 command set
INPUT 1 – 4: (1) 5-pin 3.5mm detachable terminal block;
Comprises (4) programmable digital inputs;
Input Voltage Range: 0 to 24 Volts DC, referenced to GND;
Logic Threshold: 2.5 Volts DC nominal with 1 Volt hysteresis band;
Input Impedance: 10k Ohms at >5 Volts, 1M Ohms at <5 Volts;
Pull-up Resistor: 2.2k Ohms per input
RELAY 1 – 4: (1) 8-pin 3.5mm detachable terminal block;
Comprises (4) normally open, isolated relays;
Rated 1 Amp, 30 Volts AC/DC;
MOV arc suppression across contacts
COM A – B: (2) DB9 male, bidirectional RS-232 ports;
Up to 115.2k baud, hardware and software handshaking support
NET: (4) 4-pin 3.5mm detachable terminal blocks;
Cresnet Master ports, paralleled;
Available Cresnet Power: 30 Watts
SERVICE: (1) USB Type B female, for factory use only
PoDM 48VDC IN: (1) 4-pin snap & lock power jack;
48 Volt DC power input for PoDM power pack
[3]
;
Enables PoDM and PoH power sourcing
100-240V~4.0A 50/60Hz: (1) IEC 60320 C14 main power inlet;
Mates with removable power cord, included
G: (1) 6-32 screw, chassis ground lug
LAN: (1) 8-wire RJ45 female;
10Base-T/100Base-TX/1000Base-T Ethernet port
COMPUTER (front): (1) USB Type B female;
USB computer console port (cable included)
LCD Display
Green LCD alphanumeric, adjustable backlight, 2 lines x 20 characters
per line; displays input/outputs by name, volume levels, setup menus,
signal routing, device info, and other system information
Controls & Indicators
NET: (1) yellow LED, indicates Cresnet bus activity
LAN: (1) yellow LED, indicates Ethernet activity
HW-R: (1) recessed miniature pushbutton for hardware reset, reboots the
control system
SW-R: (1) recessed miniature pushbutton for software reset, restarts the
SIMPL program
POWER: (1) pushbutton and green LED, programmable for system
power control
SOFTKEYS: (4) pushbuttons for activation of LCD driven functions and
passcode entry
MENU: (1) pushbutton, steps menu back one level
, : (2) pushbuttons, scroll up or down through menu and adjust
menu parameters
ENTER: (1) pushbutton, executes highlighted menu or value
VOLUME: (1) continuous turn rotary encoder, adjusts menu parameters,
defaults to Program audio volume
MUTE: (1) pushbutton and red LED, mutes the Program audio output
ROUTE: (1) pushbutton and red LED, selects ROUTE mode to allow
routing changes
VIEW: (1) pushbutton and red LED, selects VIEW mode to view
current routing
INFO: (1) pushbutton and red LED, selects INFO mode to view AV and
device info
INPUT 1 –6: (6) pushbuttons and red LEDs, select input to be routed
OUTPUT 1 – 2, PROG, AUX 1 – 2: (5) pushbuttons and red LEDs, select
output destination(s)
SPEAKER OUTPUT: (1) 3-position slide switch, selects the amplifier
output configuration
DM INPUT 6 (rear): (2) LEDs, green LED indicates DM link status, amber
LED indicates video and HDCP signal presence
DM INPUT 6 PoDM (rear): (1) green LED, indicates upstream device is
drawing power over DM
DM OUTPUT 2 (rear): (2) LEDs, green LED indicates DM link status, amber
LED indicates video and HDCP signal presence
DM OUTPUT 2 PoDM (rear): (1) green LED, indicates downstream device
is drawing power over DM
LAN (rear): (2) LEDs, bi-color LED (left) indicates Ethernet speed and
activity, green LED (right) indicates Ethernet link status