Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver & Room Controller 200 Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON This device includes an aggregation of separate independent works that are each generally copyrighted by Crestron Electronics, Inc., with all rights reserved.
Regulatory Compliance As of the date of manufacture, the DM-RMC-200-C has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Contents DigitalMedia 8G+™ Receiver & Room Controller 200: DM-RMC-200-C 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications........................................................................................................
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 DigitalMedia 8G+™ Receiver & Room Controller 200: DM-RMC-200-C Introduction The DM-RMC-200-C provides an advanced one-box interface solution for a single display device as part of a complete Crestron® DigitalMedia™ system. It functions as a DM 8G+™ receiver, video scaler, audio amplifier, and expanded control interface, providing a single HDMI® output along with speaker and line level audio, Ethernet, and a variety of control ports.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C Features and Functions (Continued) • • • • • • • • • • • • • • Provides automatic 3D-to-2D signal conversion1 Automatically passes 3D video without scaling to 3D capable displays1 Includes content-adaptive noise reduction 100% HDCP compliant Scalable zoom feature enables 2x2, 3x2, 3x3, 4x3, or 4x4 video wall capability2 Provides analog line and speaker level audio outputs DM 8G+ input supports up to 330 foot (100 meter) cable length3 Affords a true on
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 A single cable connects the DM-RMC-200-C to a DM® switcher or transmitter (each sold separately), transporting video, audio, control, and networking signals through one RJ-45 connection.1 Multiple DM-RMC-200-Cs may be installed to handle each display in a multi-room distribution system, all fed from a central DM switcher.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C LAN Connectivity Along with high-definition AV and control, DigitalMedia also integrates high-speed Ethernet networking for a total signal distribution solution. The DM-RMC-200-C includes a 10BASE-T/100BASE-TX Ethernet port, providing a convenient LAN connection for a local network device.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Applications The diagram below shows a DM-RMC-200-C in a standalone application. In this application, the DM-RMC-200-C is used with a DM 8G+ transmitter such as the DM-TX-201-C and is not used with a DM switcher. DM-RMC-200-C in a Standalone Application Operations & Installation Guide – DOC.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C Specifications Specifications for the DM-RMC-200-C are listed in the following table.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 DM-RMC-200-C Specifications (Continued) SPECIFICATION DETAILS Video Input Resolutions (Continued) 720 x 480 @ 30 Hz (480i) 720 x 576 @ 25 Hz (576i) 1920 x 1080 @ 25 Hz (1080i25) 1920 x 1080 @ 30 Hz (1080i30) plus any other resolution allowed by HDMI up to 165 MHz pixel clock Interlaced Scaler Output Resolutions Progressive 640 x 480 @ 60 Hz 720 x 480 @ 60 Hz (480p) 720 x 576 @ 50 Hz (576p) 800 x 600 @ 60 Hz 848 x 480 @ 60 Hz 1024 x 768 @ 60 Hz6 12
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C DM-RMC-200-C Specifications (Continued) SPECIFICATION DETAILS Audio (Continued) Performance (Analog) Amplifier Output Power8 15 Watts per channel at 8 Ohms Frequency Response 20 Hz to 20 kHz ±0.5 dB (line), 20 Hz to 16 kHz ±3 dB (speaker) S/N Ratio >95 dB (line), >75 dB (speaker) 20 Hz to 20 kHz A-weighted THD+N <0.005% @ 1 kHz (line), <0.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 DM-RMC-200-C Specifications (Continued) SPECIFICATION DETAILS Available Accessories CBL-HD Crestron Certified HDMI Interface Cable CBL-HD-DVI Crestron Certified HDMI to DVI Interface Cable CBL-RCA2 Crestron® Certified RCA Stereo Audio Interface Cable CBL-SPK-P-35 Speaker Cable, 16 AWG, Plenum, 35 ft CNSP-XX Custom Serial Interface Cable DM-CBL-8G DigitalMedia 8G Cable DM-8G-CONN-100 DigitalMedia 8G Cable Connectors Excite™ Series In-Wa
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C Physical Description This section provides information on the connections, controls and indicators available on your DM-RMC-200-C. DM-RMC-200-C Physical View (Front Panel View) DM-RMC-200-C Physical Views (Top Panel View) DM-RMC-200-C Physical Views (Bottom and Rear Panel View) 10 • DigitalMedia 8G+™ Receiver 200: DM-RMC-200-C Operations & Installation Guide – DOC.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 DM-RMC-200-C Overall Dimensions (Front and Side Panel Views without Mounting Bracket Installed) 7.63 in (194 mm) 7.48 in (190 mm) 2.0 7.92 in (202 mm) 7.55 in (192 mm) 1.06 in (27 mm) 1.40 in (36 mm) DM-RMC-200-C Overall Dimensions (Front Panel View with Mounting Bracket Installed) 10.84 in (276 mm) 2.0 1.30 in (33 mm) 4.93 in (126 mm) 3.29 in (84 mm) Operations & Installation Guide – DOC.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C DM-RMC-200-C Overall Dimensions (Side Panel View with Mounting Bracket Installed) 1.85 in (47 mm) 1.78 in (46 mm) DM-RMC-200-C Connectors, Controls & Indicators (Front Panel View) 2.0 1 2 3 4 5 6 12 • DigitalMedia 8G+™ Receiver 200: DM-RMC-200-C Operations & Installation Guide – DOC.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 DM-RMC-200-C Connectors, Controls & Indicators (Top Panel View) 9 8 7 10 DM-RMC-200-C Connectors, Controls & Indicators (Bottom Panel View) 11 12 14 13 15 DM-RMC-200-C Connectors, Controls & Indicators (Rear Panel View) 17 16 20 18 19 Operations & Installation Guide – DOC.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C Connectors, Controls & Indicators # CONNECTORS1, CONTROLS & INDICATORS 1 PWR LED (1) Green LED, indicates operating power supplied from local power pack 2 DM LINK LED (1) Green LED, indicates connection to an upstream DM device 3 VIDEO LED 4 USB HID LED (1) Green LED, indicates a valid device connection and activity on the USB HID port 5 SETUP (LED and Button) (1) Red LED and (1) miniature recessed push button for Ethernet setup 6 RESE
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS DESCRIPTION 11 DIG IN (1) 2-pin 3.5 mm detachable terminal block; Digital/contact closure sensing input; Rated for 0-24 Volts DC, referenced to GND; Input Impedance: 2.2k Ohms pulled up to 5 Volts DC; Logic Threshold: 2.5 Volts DC nominal with 1 Volt hysteresis band 12 HDMI OUT 13 USB HID (1) USB Type A female; USB 2.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS DESCRIPTION 19 DIG IN (1) 2-pin 3.5 mm detachable terminal block; Digital/contact closure sensing input; Rated for 0-24 Volts DC, referenced to GND; Input Impedance: 2.2k Ohms pulled up to 5 Volts DC; Logic Threshold: 2.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Setup Network Wiring When wiring the DM network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. CAUTION: Failure to use Crestron power supplies could cause equipment damage or void the Crestron warranty. • Provide sufficient power to the system.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C Supplied Hardware The hardware supplied with the DM-RMC-200-C is listed in the following table. Supplied Hardware for the DM-RMC-200-C DESCRIPTION PART NUMBER QUANTITY Mounting Bracket 2029286 1 Screws, 6-32 x 1”, Pan, Phil 2007250 6 Screws, 6-32 x 3/4”, Slot 2009211 4 Tie Wraps 2013608 2 Installation Ventilation The DM-RMC-200-C should be used in a well-ventilated area.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Mounting the DM-RMC-200-C Mounting Bracket (2029286) 2-Gang Electrical Box (Not Included) #6-32 x 3/4” Slot Head Screws (4) (2009211) #6-32 x 1” Phillips Head Screws (4) (2007250) 0 Installing the Power Pack The included mounting bracket (2029286), which is used to attach the DM-RMC-200-C to an electrical box, provides a holder for the included power pack.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C Installing the Power Pack Power Pack Holder 0 Tie-Wrap Holes (2) #6-32 x 1” Phillips Head Screws (2) (2007250) Power Pack (Included) Installation of the power pack in the holder is shown below. Power Pack Installed in Holder of DM-RMC-200-C Mounting Bracket 20 • DigitalMedia 8G+™ Receiver 200: DM-RMC-200-C Operations & Installation Guide – DOC.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Hardware Hookup Make the necessary connections as called out in the following illustrations. Refer to “Network Wiring” on page 17. Apply power after all connections have been made. Hardware Connections for the DM-RMC-200-C (Top Panel View) AUDIO OUT R, L (SPEAKER): Amplified Stereo Audio Output AUDIO OUT R, L (LINE): Stereo Unbalanced Line-Level Audio Output LAN: 10BASE-T/ 100BASE-TX Ethernet to Local Network Device 24 V 2.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C Hardware Connections for the DM-RMC-200-C (Rear Panel View) AUDIO OUT L, R (SPEAKER): Amplified Stereo Audio Output Ground RELAY 1-2: To Controllable Devices DM IN: From DM Switcher, Transmitter, or Other DM Device DIG IN: Software Programmable Digital Input NOTE: Ensure that the unit is properly grounded by connecting the chassis ground lug to an earth ground (building steel).
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron Web site. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at www.crestron.com/support. First-time users will need to establish a user account.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C The system tree of the control system displays the DM-RMC-200-C in the appropriate slot with a default IP ID as shown in the following illustrations. In the first example, the DM-RMC-200-C is used with the DMCO-50 output card in a DM-MD8X8 switcher. In the second example, the DM-RMC-200-C is used with the C2ENET-2 card in an Ethernet slot on the control system.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 C2ENET-2 Device, Slot 8 (Using Ethernet Slot on Control System) 2. If additional DM-RMC-200-C devices are to be added, repeat step 1 for each device. Each DM-RMC-200-C device is assigned a different IP ID. 3. If necessary, double-click a device to open the “Device Settings” window and change the IP ID as shown in the following illustration.
DigitalMedia 8G+™ Receiver 200 Program Manager Crestron DM-RMC-200-C Program Manager is the view where programmers “program” a Crestron control system by assigning signals to symbols. The symbol can be viewed by double-clicking the icon or dragging it into Detail View. Each signal in the symbol is described in the SIMPL Windows help file (F1). 26 • DigitalMedia 8G+™ Receiver 200: DM-RMC-200-C Operations & Installation Guide – DOC.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, firmware) can be transferred to the device. In addition, the IP table of the device can be configured.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C USB Communication via DM Switcher PC Running Crestron Toolbox DM- RMC- 200-C DM Switcher DM 8G+ USB To establish USB communication between the PC and the DM switcher: Via LAN Port 1. Use the Address Book in Crestron Toolbox to create an entry using the expected communication protocol (USB).
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 4. (Optional) If additional changes to TCP/IP settings are desired, do the following: a. Assign an IP address, IP mask, and default router for the DM-RMC-200-C via the Crestron Toolbox (Functions | Ethernet Addressing). b. Close the “System Info” window. c. In Crestron Toolbox, change the Address Book entry for the DM-RMC-200-C so that it uses the IP address assigned in step 4a. d.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C IP Configuration If the DM-RMC-200-C is used in a standalone configuration (i.e., not connected to a DM switcher), use Crestron Toolbox to create the IP table entry of the DM-RMC-200-C. NOTE: If the DM-RMC-200-C is connected to a DM switcher, the IP table entry of the DM-RMC-200-C is created automatically. 1. Use the Device Discovery Tool to find the IP address of the DM-RMC-200-C.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. DM-RMC-200-C Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION PWR LED does not illuminate. Device is not receiving power. Verify power supply connections to the device and to the power outlet. PWR LED flashes.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C DM-RMC-200-C Troubleshooting (Continued) TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION LAN LED does not illuminate green. LAN network cable is not connected to the LAN port or to the 10BASE-T/ 100BASE-TX compatible device. Verify LAN network cable connection to the LAN port and to the compatible network device. LAN network cable is not the proper type. Verify that network cable complies with EIA/TIA 568 and the CAT5 specification.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 Future Updates As Crestron improves functions, adds new features and extends the capabilities of the DM-RMC-200-C, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron Web site periodically for manual update availability and its relevance.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 GNU General Public License Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed. PREAMBLE The licenses for most software are designed to take away your freedom to share and change it.
DigitalMedia 8G+™ Receiver 200 Crestron DM-RMC-200-C 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 7126B (2029414) 07.11 Specifications subject to change without notice.
