CRESTRON CNRFT/CNIRT One-Way Wireless Panels TABLE OF CONTENTS DESCRIPTION................................................................................................................1 Functional Description......................................................................................1 CNRFT-32A/-48A..................................................................................1 CNIRT-32A/-48A...................................................................................
CRESTRON CNRFT/CNIRT One-Way Wireless Panels 6.4 in 16.3 cm 8.8 in 22.3 cm 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 6.2 in 15.7 cm 6.2 in 15.7 cm 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 25 26 27 28 29 30 31 32 37 38 39 40 41 42 43 44 45 46 47 48 CRESTRON CRESTRON UNIT DEPTH 2.0 in (5.1 cm) UNIT DEPTH 2.0 in (5.
CRESTRON CNRFT/CNIRT One-Way Wireless Panels Physical Description CNRFT-32A/48A and CNIRT-32A/48A electronic hardware is housed in a high-impact molded plastic enclosure (refer to figures 1 and 2 for front and back views, respectively ). The button array on the printed circuit board is covered by a customized button panel. All button panels include custom engraving, colored button caps, choice of button configurations, and panel finishes.
CRESTRON CNRFT/CNIRT One-Way Wireless Panels LEADING SPECIFICATIONS: Table 2 provides a summary of leading specifications for the wireless transmitters. Dimensions and weight are approximations rounded to the nearest tenth unit. Table 2. Leading Specifications SPECIFICATION DETAILS Battery CRESNET II Workshop CRESNET II Operating System CNRFT-32A & CNIRT-32A Dimensions & Weight 9V DC Version 5.0 or later SR30160.OPS or later Height: 6.2 in (15.7 cm) Width: 6.4 in (16.3 cm) Depth: 2.0 in (5.
CRESTRON CNRFT/CNIRT One-Way Wireless Panels CONTROLS AND INDICATORS: Controls Button controls are custom designed. The wireless transmitters are available with a maximum of 32 to 48 functional buttons (depending on the model). Function definition is determined by application of the unit within the CRESNET II system. The customized button controls correspond to signal names that are defined in the SIMPL program. Indicators There is only one indicator located on the wireless transmitters.
CRESTRON CNRFT/CNIRT One-Way Wireless Panels 3. From the MAIN MENU, highlight Utilities and depress ENTER. The UTILITY MENU, illustrated in figure 4, appears on the display. CRESNET II Workshop CRESNET v5.0 II Workshop UTILITY MAIN ESC to Transmitter ID Programmer the SIMPL (Symbol - Intensive - Master - Programming Language) program development environment. Quit Alt[D] = Set Defaults ESC F1=Help Figure 3. MAIN MENU, Workshop 4.
CRESTRON CNRFT/CNIRT One-Way Wireless Panels PROBE SHOULD COVER SENSOR A S SHOWN. Figure 6. Probe Placement 10. With a finger over the probe to hold it in place, lift and rotate transmitter so that the red LED located above the button panel is visible. 11. From the PC, type the two-digit hexadecimal ID CODE. 12. Depress the ENTER key and observe the flashing red LED on the front of the transmitter. 13. When the red LED stops flashing, remove the probe from the back of the unit.
CRESTRON CNRFT/CNIRT CRESNET II Workshop One-Way Wireless Panels CRESNET v5.0 System PF : 3.0 Net PF: II Workshop v5.0 3.0 Net ID: 03 Net ID 03: 04: 05: 06: 07: 08: 09: 0A: 0B: 0C: 0D: 0E: 0F: 10: 11: 12: ESC to Net Device Description CNRFGW P.F. CNRFGW/CNIRGW Receiver CNRFGW CNRFGW/CNIRGW Receiver 3.
CRESTRON CNRFT/CNIRT One-Way Wireless Panels Table 3. Troubleshooting Guide (Continued) TROUBLE No response from CRESNET II system. POSSIBLE CAUSE(S) CORRECTIVE ACTION Refer to causes when LED does not illuminate and Refer to corrective action when LED does not intermittent response during transmission occurs. illuminate and intermittent response during transmission occurs. NET ID of receiver is incorrectly set. Enter Performance Viewport in the CRESNET II Workshop.
CRESTRON CNRFT/CNIRT One-Way Wireless Panels SYNTAX: The following syntax codes are provided for compatibility purposes only. NET.ID <10 o FE>: CNRFGW \CNRFT talking to a CNRFGWA TRANSMITTER : CNRFT \ID # and transmitter type. i1 = \Independent button. i2 = i3 = " = " " R E M O T E C O N T R O L NET.
