Crestron CN-WP12F and CN-WP12N Source and Numeric Keypads Contents Source and Numeric Keypads: CN-WP12F and CN-WP12N Description Functional Description Physical Description Leading Specifications Setup Custom Switch Cap Installation Network Wiring Keypad Installation Identity Code Programming with SIMPL™ Windows How the Program Works How to Create the Program Problem Solving Troubleshooting Further Inquiries Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty Oper
Crestron CN-WP12F and CN-WP12N Source and Numeric Keypads Source and Numeric Keypads: CN-WP12F and CN-WP12N Description Functional Description The Source and Numeric Keypads, CN-WP12F and CN-WP12N, are wall-mounted user-interface devices designed to work with the CNX-PAD8 Professional Audio Distribution Processor. The keypads are installed into the physical rooms of a building to control the CNX-PAD8 and its audio source devices. The CN-WP12F serves as the source keypad.
Source and Numeric Keypads Crestron CN-WP12F and CN-WP12N CN-WP12F and CN-WP12N Source and Numeric Keypads CN-WP12F SOURCE SELECTOR BUTTONS WITH LED INDICATORS ON/OFF AND MUTE BUTTONS WITH LED INDICATORS CD FM CD 2 DSS TAPE AUX ON/OFF MUTE 4.10 in (10.41 cm) (SIDE VIEW OF BOTH CN-WP12F AND CN-WP12N) VOL VOL TRANSPORT CONTROL AND VOLUME BUTTONS (WITHOUT LEDs) KEYPAD KEYPAD MOUNTING ASSEMBLY NETWORK WIRING CONNECTOR 1.74 in (4.
Crestron CN-WP12F and CN-WP12N Source and Numeric Keypads Leading Specifications The table below provides a summary of leading specifications for the CN-WP12F and CN-WP12N. Dimensions and weight are rounded to the nearest hundredth unit. Leading Specifications of the CN-WP12F and CN-WP12N SPECIFICATION SIMPL Windows CNX Upgrade File CNHome.
Source and Numeric Keypads 2. Crestron CN-WP12F and CN-WP12N Grasp the lower-sides of the keypad and gently pull the bottom of the keypad outwards as shown below. Keypad Removal CAUTION: To avoid damage to the keypad shell during the next step, do not use excessive force when prying the shell outwards. NOTE: The position of each switch cap is important to the CNX-PAD8 program. Notice the location of each switch cap before disassembly. 3.
Crestron CN-WP12F and CN-WP12N 4. Source and Numeric Keypads As shown below, remove the switch cap to be replaced from the rubber button actuator. Make sure that the indicator lens of the custom switch cap is above the LED and install the custom switch cap onto the button actuator. Install Custom Switch Cap CD DSS 2 LED FM CD 2 DSS TAPE AUX ON/OFF MUTE VOL VOL 5.
Source and Numeric Keypads Crestron CN-WP12F and CN-WP12N CAUTION: To avoid damage to the pins of the plug, do not use excessive force when seating the keypad into the keypad mounting assembly. When properly aligned, the 18-pin plug inserts easily into the socket 8. As shown below, insert the keypad upper-tab into the keypad mounting assembly upper-slot. Align the keypad 18-pin plug with the assembly 18-pin socket and gently push the keypad inward until it is fully seated. Install Keypad 9.
Crestron CN-WP12F and CN-WP12N Source and Numeric Keypads Wire Gauge Values RESISTANCE (R) W IRE GAUGE 4 6 10 15 16 18 20 22 NOTE: All network wiring must consist of two twisted-pairs. One twisted pair is the +24V conductor and the GND conductor and the other twisted pair is the Y conductor and the Z conductor. NOTE: When daisy-chaining network units, always twist the ends of the incoming wire and outgoing wire which share a pin on the network connector.
Source and Numeric Keypads Crestron CN-WP12F and CN-WP12N 6. When the assigned NET ID appears, select the Set ID button to initiate the change. 7. The software responds with a successful message to confirm the changed NET ID. 8. To verify this procedure, select Diagnostics | Report Network Devices. Confirm that the keypad has a new NET ID code. 9. Reconnect other network devices that were disconnected in step 1.
Crestron CN-WP12F and CN-WP12N Source and Numeric Keypads Block Diagram of CN-WP12F SIMPL Program Block Diagram of CN-WP12N SIMPL Program How to Create the Program Configuration Manager Use the Configuration Manager workspace (Project | Configure System) in SIMPL Windows to select and configure all the devices that need to be included into the system. For this example, from the Control Systems folder in the Device Library select CNMSX-PRO.
Source and Numeric Keypads Crestron CN-WP12F and CN-WP12N System View of the CN-WP12F in SIMPL Windows’ Configuration Manager System View of the CN-WP12N in SIMPL Windows’ Configuration Manager Programming Manager Use the Programming Manager workspace (Project | Program System) in SIMPL Windows to select symbols and assign their respective signals. For this example, CN-WP12F and CN-WP12N symbols were added automatically when the devices were added to the system in the Configuration Manager workspace.
Crestron CN-WP12F and CN-WP12N Source and Numeric Keypads Detail View of the CN-WP12F Symbol in SIMPL Windows’ Programming Manager Detail View of the CN-WP12N Symbol in SIMPL Windows’ Programming Manager Operations Guide - DOC.
Source and Numeric Keypads Crestron CN-WP12F and CN-WP12N Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron technical support representative. CN-WP12F and CN-WP12N Troubleshooting TROUBLE Keypad does not function when a button is depressed. Keypad functions but LED indicator does not illuminate. POSSIBLE CAUSE(S) Keypad is not receiving network power. Keypad NET ID is not unique.
Crestron CN-WP12F and CN-WP12N Source and Numeric Keypads Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
