Specifications

ManualsBrandsCrestron ManualsComputer equipmentCLW-SLVS1

CLW-SW1, SWS1, & SLVS1(W/A/B)

CLW-SW1, CLW-SWS1, & CLW-SLVS1 Specifications

(Continued)

Introduction

SPECIFICATION DETAILS

Load Type Incandescent, Tungsten Halogen,

Fluorescent / High Intensity

Discharge (HID), Electronic Low

Voltage, Magnetic Low Voltage, Neon

/ Cold Cathode, General Purpose Fan

2-Series Control System

Update File

1,2

Version 3.117 or later

Load Ratings

Incandescent / Tungsten

Halogen

-SW1: 1000W

-SWS1: 1000W

-SLVS1: N/A

Magnetic Low Voltage

-SW1: 1000VA/750W

-SWS1: 1000VA/750W

-SLVS1: N/A

Neon / Cold Cathode

-SW1: 1000VA/750W

-SWS1: 1000VA/750W

-SLVS1: N/A

Electronic Low Voltage -SW1: 1000W

-SWS1: 1000W

-SLVS1: N/A

Fluorescent / High

Intensity Discharge

(HID)

-SW1: 8A

-SWS1: 8A

-SLVS1: N/A

General Purpose Fan -SW1: 3.0A

-SWS1: 3.0A

-SLVS1: N/A

Minimum Load 40W / 0.5A

Operating Temperature

and Humidity

32°F to 104°F (0°C to 40°C )

10 to 90% Relative Humidity

(Non-Condensing)

Dimensions and Weight -SW1 and -SWS1:

Height: 4.13 in (10.48 cm)

Width: 2.38 in (6.03 cm)

Depth: 1.91 in (4.85 cm)

Weight: 4.4 oz (0.61 kg)

-SLVS1:

Height: 4.13 in (10.48 cm)

Width: 1.75 in (4.45 cm)

Depth: 1.91 in (4.85 cm)

Weight: 3.6 oz (0.50 kg)

Features and Functions

The CLW-SW1 (-SW1) is a stand-alone wall box switch

that can also act as a Cresnet

device that reports to a

Crestron

control processor. The -SW1 includes two

isolated, non-polarized Cresnet wires (plus a ground wire)

for connecting to a Cresnet system over a twisted pair

wire with shield.

The CLW-SW1 features a three-position mode selection

switch. Refer to “Operation ” on page 5 for more

information. In the absence of Cresnet communications,

the switch can still be used to control a load.

The CLW-SWS1 (-SWS1) is similar to the -SW1 with the

added capability of working with a slave unit

(CLW-SLVS1) in a multi-switch / single circuit

application.

The CLW-SLVS1 (-SLVS1) is a slave unit that when

used in conjunction with the -SWS1 acts as an additional

switch control point in a multi-switch / single circuit

application. It does not connect to a Cresnet system and

cannot be used without a -SWS1. The -SLVS1 does not

have a mode selection switch and is not programmable. It

emulates the operation of the -SWS1 to which it is

connected unless the mode selection switch of the master

is set to “OFF”.

These switches are available in a variety of colors and

textures. The table below shows the availability.

Available Colors/Textures

COLOR/

TEXTURE

MODEL NUMBER

SUFFIX

MATCHING LUTRON

FACEPLATE

White W Not Applicable

Smooth White W-S CW-1-WH

Almond A CW-1-LA

Smooth Almond A-S CW-1-LA

Black B Not Applicable

Smooth Black B-S CW-1-BL

1. The latest software versions can be obtained from the Crestron

website. Refer to the NOTE following these footnotes.

2. Crestron 2-Series control systems include the AV2 and PRO2.

Consult the latest Crestron Product Catalog for a complete list of

2-Series control systems.

Specifications

3. Refer to Derating Charts for Multigang Installations on pages 3

and 4.

Following are specifications for the -SW1, -SWS1, and

-SLVS1.

4. VA ratings are for input power to the transformer. If you do not

know the input power requirement of the transformer, use the

bulb’s wattage rating to determine proper rating.

CLW-SW1, CLW-SWS1, & CLW-SLVS1 Specifications

SPECIFICATION DETAILS

Power Requirements Line Power, 120 VAC, 60 Hz

Default Net ID SW1: 82

SWS1: 83

NOTE: Crestron software and any files on the website

are for Authorized Crestron dealers and Crestron

Authorized Independent Programmers (CAIP) only. New

users may be required to register to obtain access to

certain areas of the site (including the FTP site).

(Continued on next column)

Crestron Electronics, Inc. Installation Guide – DOC. 6251B

15 Volvo Drive Rockleigh, NJ 07647 (2009753)

Tel: 888.CRESTRON 06.07

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Summary of content (8 pages)

PAGE 1
CLW-SW1, SWS1, & SLVS1(W/A/B) CLW-SW1, CLW-SWS1, & CLW-SLVS1 Specifications (Continued) Introduction SPECIFICATION Features and Functions The CLW-SW1 (-SW1) is a stand-alone wall box switch that can also act as a Cresnet® device that reports to a Crestron® control processor. The -SW1 includes two isolated, non-polarized Cresnet wires (plus a ground wire) for connecting to a Cresnet system over a twisted pair wire with shield.
PAGE 2
CLW-SW1, SWS1, & SLVS1(W/A/B) Physical Description The -SW1 and -SWS1 contain one large pushbutton, a light emitting diode (LED) with software adjustable brightness*, and a three-position slider-switch, shown after this paragraph. Line voltage connections are made at the rear of the switch. Three Class 2 low voltage wires, located on the front of the switch, provide a Cresnet connection to a control system. The wires can be routed to the bottom of the unit for placement outside of the wall box.
PAGE 3
CLW-SW1, SWS1, & SLVS1(W/A/B) the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: recommends using 3 ½” deep wallboxes. Several devices can be installed in one wall box (multigang). This requires the removal of side sections (shown below) and the derating of the switching device. For a smooth appearance, onepiece multigang faceplates (not supplied) can be installed. Reorient or relocate the receiving antenna.
PAGE 4
CLW-SW1, SWS1, & SLVS1(W/A/B) Derating Information for Magnetic Low Voltage and Neon/Cold Cathode Applications* Part Number No Side Removed One Side Removed Two Sides Removed -SW1 1000VA/750W 600VA/450W 400VA/300W -SWS1 1000VA/750W 600VA/450W 400VA/300W -SLVS1 * No Derating Necessary VA ratings are for input power to the transformer. If you do not know the input power requirement of the transformer, use the bulb’s wattage rating to determine proper rating.
PAGE 5
CLW-SW1, SWS1, & SLVS1(W/A/B) section 725-55, Part D of the 2002 National Electric Code. 3. 4. 5. 3. Wire the switches as shown in Figure 3 on page 8. Wire the switch as shown in Figure 1 on page 8. NOTE: Do not connect the BLUE (Slave) wire to the Black (Hot) or RED (Load) wires. NOTE: The RED (Load) and BLACK (Hot) wires are #14 AWG. The BLUE (Slave) and WHITE (Neutral) wires are #18 AWG. The GREEN (Ground) wire is #16 AWG. The GRAY (Cresnet) wires are #22 AWG.
PAGE 6
CLW-SW1, SWS1, & SLVS1(W/A/B) Software (Continued) Buttons of CLW-SW1, -SWS1, and -SLVS1 Button REQUIRED SOFTWARE VERSION Crestron D3 Pro™ version 2.1.7 or later with D3 Pro Templates version 2.0.1 or later. Refer to software release notes or Crestron website for other required Crestron software packages.
PAGE 7
CLW-SW1, SWS1, & SLVS1(W/A/B) Return and Warranty Policies Problem Solving Merchandise Returns / Repair Service Troubleshooting 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
PAGE 8
CLW-SW1, SWS1, & SLVS1(W/A/B) Appendix: Wiring Diagrams Following are wiring diagrams for circuits that may be found when installing a switch: Stand-Alone Installations Figure 1: Wiring a CLW-SW(S)1 To continue a circuit past a switched light fixture to one or more duplex receptacles, connect the switch as shown in the following diagram.