Specifications

CLW-DIM1, DIMS1, & SLVD1(W/A/B)
NOTE: The RED (Load) and BLACK (Hot) wires are
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG. The GRAY (Cresnet) wires are #22 AWG. The
BLACK wire (Cresnet ground) paired with the GRAY
(Cresnet) wires is #22 AWG.
Operating Button and Switch
The -DIM1, -DIMS1, and -SLVD1 have one large
pushbutton. The -DIM1 and -DIMS1 also have a three-
position mode selection switch. The function of the
pushbutton is determined by the position of the mode
selection switch. Refer to the following diagram.
CLW-DIMS1 with CLW-SLVD1 Wiring
NOTE: The -SLVD1 does not have a mode selection
switch. It will act in the same mode as the -DIMS1.
NOTE: The -DIMS1 must be installed in the same
wallbox that contains the connections to the load.
Buttons of CLW-DIM1, -DIMS1, and -SLVD1
The following wiring diagram illustrates installation of
the -DIMS1 with multiple -SLVD1s.
Button
Mode Selection Switch
(-DIM1 & -DIMS1 Only)
Wiring Diagram of CLW-DIMS1 with multiple CLW-SLVD1s
Hot
Neutral
Load
RED
CLW-DIMS1
BLACK
WHITE
CLW-SLVD1
BLUEBLACK BLUE
Ground Ground
GREEN GREEN
LINE
120VAC
60Hz
WHITE
Ground
GREEN
BLACK BLUE
CLW-SLVD1
WHITE
Cresnet
OFF
When the mode selection switch is in the “OFF” position,
the pushbutton will not have any function and the load is
disconnected from the power source. This must be used
when changing light bulbs to ensure that the load is fully
disconnected from power.
NOTE: Do not connect the BLUE (Slave) wire to the
Black (Hot) or RED (Load) wires.
ADJ
When the mode selection switch is in the “ADJ” position,
the pushbutton is used to switch between the “Preset 1-
High” and “Preset 1-Low” presets (typically “On” and
“Off”) as well as adjust the lighting level. Tap the
pushbutton to fade up or down to either of the two preset
lighting levels. Tap the pushbutton while the lighting
level is fading to jump directly to the preset lighting level
without fading. (i.e., tapping while the lighting level is
fading up will jump to the “Preset 1-High” level without
fading, tapping while the lighting level is fading down
will jump to the “Preset 1-Low” level without fading).
While the light is off, double-tap the pushbutton to jump
directly to the “Preset 1-High” lighting level without
fading.
NOTE: The RED (Load) and BLACK (Hot) wires are
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG. The GRAY (Cresnet) wires are #22 AWG. The
BLACK wire (Cresnet ground) paired with the GRAY
(Cresnet) wires is #22 AWG.
NOTE: If a -DIMS1 is installed without a -SLVD1, the
BLUE lead (Slave) should be capped.
5. Splice the gray wires of the -DIM1 or -DIMS1 to
the Class 2 low voltage wires connected to the
Crestron control system or a Crestron connection
block device. Push the wires and the splices into
a hole in the drywall to provide the necessary
separation.
The lighting level can be adjusted by pressing and holding
the pushbutton. After a ½ second, the lighting level will
ramp up or down. The lighting level will stop at
maximum brightness (100%) if the lighting level was
ramping up or minimum brightness (0%) if the lighting
level was ramping down. To continue ramping the
lighting level in the opposite direction, release the
pushbutton, then press and hold the pushbutton again.
6. Push all Class 1 power wires back into the
wallbox and fasten the device to the wallbox
with the provided screws.
7. Attach decorative faceplate.
8. Restore power.
When the desired lighting level is reached, release the
pushbutton.
Installation Guide – DOC. 6250 Stand Alone Wall Box Dimmer: CLW-DIM1, DIMS1, & SLVD1 • 5