Specifications
CLW-DIM1, DIMS1, & SLVD1(W/A/B)
Introduction
Specifications
Following are specifications for the -DIM1, -DIMS1, and
-SLVD1.
Features and Functions
The CLW-DIM1 (-DIM1) is a stand-alone wall box
dimmer that can also act as a Cresnet
®
device that reports
to a Crestron
®
control processor. The CLW-DIM1 has
two preset lighting levels that can be adjusted (refer to
note below). The CLW-DIM1 also includes two isolated,
non-polarized Cresnet wires (plus a ground wire) for
connecting to the Cresnet network over a twisted pair
wire with shield.
CLW-DIM1, CLW-DIMS1, & CLS-SLVD1 Specifications
SPECIFICATION DETAILS
Power Requirements Line Power, 120 VAC, 60 Hz
Default Net ID -DIM1: 80
-DIMS1: 81
Switch Type Dimmer
Load Type Incandescent, Tungsten-Halogen,
Magnetic Low Voltage
2-Series Control System
Update File
1,2
Version 3.117 or later
Load Ratings
3
Incandescent/Tungsten
Halogen
-DIM1: 1000W
-DIMS1: 1000W
-SLVD1: N/A
Magnetic Low Voltage
4
-DIM1: 1000VA/750W
-DIMS1: 1000VA/750W
-SLVD1: N/A
Operating Temperature
and Humidity
32°F to 104°F (0°C to 40°C)
10 to 90% Relative Humidity
(Non-Condensing)
Dimensions and Weight -DIM1 and -DIMS1:
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.91 in (4.85 cm)
Weight: 4.9 oz (0.67 kg)
-SLVD1:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.91 in (4.85 cm)
Weight: 3.6 oz (0.50 kg)
NOTE: The two preset levels are noted as Preset 1-High
and Preset 1- Low. “Preset 1-High” is usually used for
turning lights on to full brightness while preset “Preset 1-
Low” is usually used for turning the lights off. Although
“Preset 1-High” and “Preset 1-Low” are usually used for
“On” and “Off” respectively, the light level for each
preset can be customized by the user. Refer to “Operating
Button and Switch” on page 5 for more information on
customizing light levels.
The CLW-DIM1 features a three-position mode selection
switch. Refer to “Operating Button and Switch” on page 5
for more information. In the absence of Cresnet
communications, the dimmer can still be used to control
lighting.
The CLW-DIMS1 (-DIMS1) is similar to the -DIM1 with
the added capability of working with a slave unit
(CLW-SLVD1) in a multi-switch / single circuit
application.
The CLW-SLVD1 (-SLVD1) is a slave unit that when
used in conjunction with the -DIMS1 acts as an additional
dimmer control point in a multi-dimmer / single circuit
application. It does not connect to a Cresnet system and
cannot be used without a -DIMS1. The -SLVD1 does not
have a mode selection switch and is not programmable. It
emulates the operation of the -DIMS1 to which it is
connected.
1. The latest versions can be obtained from the Downloads | Software
Updates section of the Crestron website (www.crestron.com).
Refer to NOTE below.
2. Crestron 2-Series control systems include the AV2 and PRO2.
Consult the latest Crestron Product Catalog for a complete list of
2-Series control systems.
3. Refer to Derating Charts for Multigang Installations on page 3.
The -DIM1, -DIMS1, and -SLVD1 are available in white,
almond, and black. White units are designated by part
numbers ending in “W”. Almond units are designated by
part numbers ending in “A”. Black units are designated by
part numbers ending in “B”. Each dimmer can be covered
with a decorative faceplate (not supplied).
4. VA ratings are for input power to the transformer. If you do not
know the input power requirement of the transformer, use the
bulb’s wattage rating to determine proper rating.
NOTE: Crestron software and any files on the website
are for Authorized Crestron dealers and Crestron
Authorized Independent Programmers (CAIP) only. New
users may be required to register to obtain access to
certain areas of the site (including the FTP site).
Crestron Electronics, Inc. Installation Guide – DOC. 6250
15 Volvo Drive Rockleigh, NJ 07647 07.04
Tel: 888.CRESTRON
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.