Specifications

ManualsBrandsCrestron ManualsHome building and DecorCLS-C6

iLux Lighting Systems

Crestron Electronics, Inc. Installation Guide – DOC. 6394F

15 Volvo Drive Rockleigh, NJ 07647 (2013406)

Tel: 888.CRESTRON 03.13

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Introduction

Features and Functions

The iLux

units, CLS-C6 and CLS-C6M, are complete integrated wall-mounted lighting systems that can function

as standalone devices or be part of a total Crestron

solution. The units are functionally identical except that the

CLS-C6M includes a built-in motion sensor.

CLS-C6M with Cover Open (Shown in Almond)

Specifications

Following are specifications for the iLux units.

CLS-C6 & CLS-C6M Specifications

SPECIFICATION DETAILS

Power Requirements

Line Power, 120 Vac, 60 Hz

Load Ratings

Max load per channel

Min load per channel

Max load per unit

800 W/VA (6.6 Amps @ 120 Vac), expandable via CLS-EXP expansion

modules (sold separately)

15 W/VA (0.125 Amps @ 120 Vac)

1920 W/VA (16 Amps @ 120 Vac)

Load Types LED

, Incandescent, Magnetic Low-voltage, Neon/Cold Cathode, 2-Wire

Dimmable Fluorescent, DQG Non-Dim Lighting;

ectronic Low-volt

age, 3 and 4-Wire Fluorescent, High-Inrush Switching,

and 277 V via CLS-EX

P Series expansion modules

Cresnet Power Available

for Local Devices

10 W Maximum

External power supplies sold separately

IR Receiver

Reception Frequency

36 kHz, For use with Crestron IR remote CLS-IRHT8

(Continued on following page)

Summary of content (14 pages)

PAGE 1
iLux Lighting Systems Introduction Features and Functions The iLux® units, CLS-C6 and CLS-C6M, are complete integrated wall-mounted lighting systems that can function as standalone devices or be part of a total Crestron® solution. The units are functionally identical except that the CLS-C6M includes a built-in motion sensor. CLS-C6M with Cover Open (Shown in Almond) Specifications Following are specifications for the iLux units.
PAGE 2
iLux Lighting Systems CLS-C6 & CLS-C6M Specifications (Continued) SPECIFICATION Motion Detector (CLS-C6M only) Type Range Default Net ID Environmental Temperature Humidity Enclosure Overall Dimensions: Height Width Depth Weight DETAILS Infrared 20 to 30 feet at 4-foot elevation (6 to 9 meters at 1.2 meter elevation) 1F 32° to 104° F (0° to 40° C) 10% to 90% RH (non-condensing) Mounts in a 4-gang electrical box, 3 1/2" (89 mm) deep minimum 4.48 in (114 mm) 8.89 in (226 mm) 2.47 in (63 mm) for CLS-C6 2.
PAGE 3
iLux Lighting Systems Installation Important Notes (Read Before Installation) • Codes: Install in accordance with all local and national electrical codes. • Wiring: Use copper wire only. For supply connections, use wires rated for at least 75° C. • Lighting Load Types: LED, incandescent, magnetic low-voltage, neon/cold cathode, 2-wire dimmable fluorescent, and non-dim lighting.
PAGE 4
iLux Lighting Systems CLS-C6M Installation 4-Gang Electrical Box Mounting Screws (4) Control Panel Overlay Front Cover Assembly 3. Remove the control panel overlay from the unit (it is held in place by small tabs and lifts off) to reveal the upper mounting screw holes. 4. Refer to the diagram below for connection of the ac wiring. All wires to be inserted in the screw terminals should be stripped 7/16 inch (~11 mm), and screws should be tightened to between 8 and 10 in.-lbs. (0.90 to 1.
PAGE 5
iLux Lighting Systems Adding External Power Supplies Additional power supplies are required to support more than four keypads or shade controllers on the LOCAL DEVICES network. Also, each C2N-SDC-DC, CSM-QMT50-DCCN and CSC-DCCN shade controller requires its own additional power supply. The diagram below illustrates a scenario where an external power supply is required to add a shade controller and other devices to a network that already contains four shade controllers.
PAGE 6
iLux Lighting Systems Wiring Occupancy Sensors and Photocells NOTE: Ensure that all CLS-C6 and CLS-C6M devices contain the latest firmware to take advantage of the most recently released features.
PAGE 7
iLux Lighting Systems Setup Network Wiring When wiring the network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (http://www.crestron.com/calculators).
PAGE 8
iLux Lighting Systems CLS-C6 Installation Configurations (Continued) Method 3: Same as (1) plus a 2-Series control system communicating with the CLS. 2-Series Control System Cresnet Cresnet (Control System) Other Cresnet Devices Why? Control system can control and monitor operation of the lighting system. Can trigger lighting scenes from touch screens, RF wireless remotes, computers, or real-time clock. Buttons on lighting system can control other functions.
PAGE 9
iLux Lighting Systems Supported Devices The following table lists devices supported by the iLux units and their power requirements. Supported Devices Power Requirements NAME DESCRIPTION CRESNET POWER FACTOR (W) MAX QTY C2N-DB6 6-Button Keypad 3 watts 16 C2N-DB8 8-Button Keypad 3 watts 16 C2N-DB12 12-Button Keypad 3 watts 16 C2N-CBD/CBF (All Models) ® Cameo Keypad 0.5 watts 16 C2NI-CB/ INETI-CB Cameo Keypad (International) 0.
PAGE 10
iLux Lighting Systems Testing The following illustration shows the front panel of the unit and the controls used during installation. Front Panel Controls and Indicators LED Bar Graphs 1 2 3 4 Two-Digit Lights Display Button 5 6 M in S ec ^ ^ S cene 1 S cene 2 S cene 3 S cene 4 S cene 5 Ligh ts S hade s S ave C an cel S cene 6 ^ ON ^ OFF Function Buttons Verify the basic installation and wiring connections as follows: 1.
PAGE 11
iLux Lighting Systems Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. CLS-C6/C6M Installation Troubleshooting TROUBLE Unit does not function. * POSSIBLE CAUSE(S) CORRECTIVE ACTION Unit is not receiving line power. Verify that the unit is properly connected to the power line and that the circuit breaker is closed. Loads are not connected.
PAGE 12
iLux Lighting Systems Strip and Tin Wire When daisy chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors. Twist together the ends of the wires that share a pin on the network connector and tin the twisted connection. Apply solder only to the ends of the twisted wires. Avoid tinning too far up the wires or the end becomes brittle. Insert the tinned connection into the Cresnet connector and tighten the retaining screw.
PAGE 13
iLux Lighting Systems Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
PAGE 14
iLux Lighting Systems This page is intentionally left blank. 14 • iLux Lighting Systems: CLS-C6 & CLS-C6M Installation Guide – DOC.