Crestron CAGE2 3-Card Expansion Cage for AV2 Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc.
Crestron CAGE2 3-Card Expansion Cage for AV2 Contents 3-Card Expansion Cage for AV2: CAGE2 1 Description................................................................................................................................. 1 Functional Description ................................................................................................ 1 Physical Description.................................................................................................... 1 Leading Specifications.....
Crestron CAGE2 3-Card Expansion Cage for AV2 3-Card Expansion Cage for AV2: CAGE2 Description Functional Description The CAGE2 is an optional field-upgradeable card cage chassis for the Crestron AV2 integrated control system. When installed, the CAGE2 provides three slots that accept any combination of 2-Series Y-BUS and/or CNX series plug-in control cards to expand and add versatility to the AV2.
3-Card Expansion Cage for AV2 Crestron CAGE2 CAGE2 Top and Side Views 7.12 in (18.08 cm) CAGE2 Reference Diagram EXPANSION CARD GUIDE (TWO PER SLOT) EXPANSION CARD CONNECTORS CAGE2 TO AV2 CONNECTOR J2 FACEPLATE MOUNTING BRACKET (TWO PER SLOT) J3 J1 J4 UNDERSIDE MOUNTING HOLES (ONE PER SIDE) REAR MOUNTING HOLES (FOUR TOTAL) 2 • 3-Card Expansion Cage for AV2: CAGE2 BLANK FACEPLATES PCB INTERCONNECT JUMPER Installation Guide - DOC.
Crestron CAGE2 3-Card Expansion Cage for AV2 Leading Specifications The table below provides a summary of leading specifications for the CAGE2. Dimensions and weight are rounded to the nearest hundredth unit. Leading Specifications of the CAGE2 SPECIFICATION DETAILS SIMPL™ Windows® 2-Series Control System Update File 2 Dimensions & Weight Version 2.00 or later 1 Version 1.000.CUZ or later 3 Height: 3.00 in (7.62 cm) Width: 6.60 in (16.77 cm) Depth: 7.12 in (18.08 cm) Weight: 11.70 oz (0.
3-Card Expansion Cage for AV2 1. Crestron CAGE2 Refer to the diagram below. Using a #2 Phillips screwdriver, remove four cover top screws. CAGE2 Installation (1 of 11) - Remove Cover Top Screws NOTE: The AV2 cover top screws are 0.250 in long and the cover side screws are 0.375 in long. Keep the screws separate to ease reassembly. 2. Refer to the diagram below. Using a #2 Phillips screwdriver, remove six cover screws from each side of the AV2.
Crestron CAGE2 3-Card Expansion Cage for AV2 NOTE: During the next step, the four SEM (attached washer) screws must be retained to install the CAGE2. However, the blank plate will not be reused. 4. Refer to the diagram below. Use a #2 Phillips screwdriver to remove four rear-mounting SEM screws that secure the AV2 blank plate and remove the plate.
3-Card Expansion Cage for AV2 6. Crestron CAGE2 Refer to the diagram below. Attach either long-edge of the supplied PCB jumper to the interconnect connector (J1) on the CAGE2. CAGE2 Installation (5 of 11) - Attach PCB Interconnect Jumper to CAGE2 J1 7. Refer to the diagram below. Rotate the CAGE2 assembly until the CAGE2 connector backplane is towards the AV2 front panel and position into AV2.
Crestron CAGE2 3-Card Expansion Cage for AV2 8. Refer to the diagram below. Align the PCB jumper to the AV2 processor board connector and slide the CAGE2 assembly towards rear of AV2. Make sure that PCB jumper is inserted into the AV2 connector and align the CAGE2 bottom and rear mounting holes. CAGE2 Installation (7 of 11) - Slide CAGE2 Assembly Rearwards 9. Refer to the diagram below.
3-Card Expansion Cage for AV2 Crestron CAGE2 10. Refer to the diagram below. Re-install the the four rear-mounting SEM (attached washer) screws that were removed in step 4 to finger-tight then, using a #2 Phillips tip screwdriver tighten the screws an additional 1/8-turn. CAGE2 Installation (9 of 11) - Re-install Rear-Mounting Screws 11. Position cover onto the AV2. NOTE: The AV2 cover side screws are 0.375 in long and the cover top screws are 0.250 in long.
Crestron CAGE2 3-Card Expansion Cage for AV2 CAGE2 Installation (11 of 11) - Re-install Cover Top Screws 14. Refer to the installation and operation guide supplied with the expansion card for card installation instructions. If more than one plugin expansion card is to be utilized in the AV2, additional face-plate(s) of the CAGE2 must be removed.
3-Card Expansion Cage for AV2 Crestron CAGE2 Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. CAGE2 Troubleshooting POSSIBLE CAUSE(S) TROUBLE Expansion card(s) do not function properly. * PCB interconnect jumper not installed PCB interconnect jumper defective. CAGE2 interconnect connector J1 pin(s) or AV2 backplane connector damaged.
Crestron CAGE2 3-Card Expansion Cage for AV2 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide - DOC. 5964 11.01 Specifications subject to change without notice.
