User and Installation Manual ILT2 motorized screens INTERFACE Manual INTERFACES for ILT2 powered screens rev.
Manual Connections ILT-4 Somfy Your screen is equipped with Somfy ILT2 motors which allows more presets than standard Somfy Motors (LT50 or LS40) This screen needs to be controlled could be controlled using two controllers: SOMFY® interface called “SOMFY® 4ILT interface” RS485 (+ converter RS232) Following instructions concern the “SOMFY® 4ILT control box”. The following interfaces can be used to connect up to 4 ILT2 Somfy motors on the 2‐way or 4‐way masked screens.
Manual Connections ILT-4 Somfy INTRODUCTION This manual is an integral part of the product and must be read and understood in all its parts for safety reasons. It contains norms and directions for correct and safe use of the interface. The manual should never be separated from the product; it must be stored in a suitable place to ensure its integrity, and in such a way as to be easily consulted by authorised personnel. Product user shall be responsible for the manual’s safekeeping.
Manual Connections ILT-4 Somfy General connections 12V Trigger IR Sensor RS485 NC = Not connected RS485 B RS485 A G = Ground + = 5 30V G = Ground Adapter RS232 RS485 A = ‐ RS232 RS485 B = + RS232 Transmission distance: 1000 meters/3281 feet ILT2 motors connections SCREEN Fixed 4 Way Fixed 2 Way lateral Fixed 2 Way Top-Bottom Rolling 4 Way Rolling Top-Bottom ILT plug M1 Left Mask Left Mask Not connected Projection Fabric Projection Fabric ILT plug M2 Right Mask Right Mask Not connected Top Mask
MOTOR SETTING ENGLISH End limits motors setting with MCS-ILT-T setting tool 1. Connect the setting tool to the motor with the phone cable. The LED light turns on. 2. Push the selector switch into the up position. 3. Press the UP or DOWN button of the setting tool. Check if the UP push button controls the UP direction and the DOWN one the DOWN motion. If not, reverse the rotation direction simply by pushing the STOP push button (1 sec). 4.
INSTRUCTION ENGLISH SOFTWARE PROVIDED To control the screens with ILT4 and control serial (RS232 or RS485) are available the following software: EventGhost_0.3.7.r1170 (Software: http://www.eventghost.org /downloads/EventGhost_0.3.7.r1462_Setup.exe ) (Download package: http://www.screenresearch.com/website/documents/software_current/IL T%20interface.rar ) Description: EventGhost Software is an advanced, easy to use and extensible automation tool for MS Windows.
INSTRUCTION ENGLISH INSTALLATION SCREEN and INTERFACE: A) Connect each motor to the power supply B) Connect the ILT interface to the power supply and wait initialization time of 15 seconds C) Plug RJ9 from each motors into the ILT Interface D) Plug your RS485 cable between your computer and the ILT interface as shown in the documentation provided SOFTWARE: A) Install and Launch EventGhost Software B) Load/Open file "Remote control XMask 2.
INSTRUCTION ENGLISH DATA PARAMETER SERIAL Commands Code ASCII Code Hexadécimal Select format 1 7FF3FBFFFFFF000000FE0668 \x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFE\x06\x68 Select format 2 7FF3FBFFFFFF000000FD0667 \x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFD\x06\x67 Select format 3 7FF3FBFFFFFF000000FC0666 \x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFC\x06\x66 Select format 4 7FF3FBFFFFFF000000FB0665 \x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFB\x06\x65 Select format 5 7FF3FBFFFFFF000000FA0664 \x7F\xF3\xFB
RS485 REMOTE ENGLISH SOMFY INFRARED CODE "1" Alternate Pattern "2" Alternate Pattern "3" Alternate Pattern "4" Alternate Pattern "5" Alternate Pattern "6" Alternate Pattern "7" Alternate Pattern "8" Alternate Pattern "UP" Alternate Pattern "DOWN" Alternate Pattern "STOP" Alternate Pattern "1-4" Alternate Pattern "1-8" Alternate Pattern "5-8" Alternate Pattern "PROG" Alternate Pattern 0000 006b 0000 0017 0015 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 00
CONTACTS ADEO SCREEN Sp. z o.o. Ul. Boleslawa Krzywoustego 31 59-500 Zlotoryja Polska - Europe Tel. +48 76 850 53 05 Fax + 48 76 850 53 70 Italia Tel. +39 0461-248211 Fax +39 0461-243850 Email To contact Technical support: techsupport@screenresearch.com info@adeoscreen.com © Copyright 2014 Adeo Screen. All rights reserved. Manual ILT2 motorized screens INTERFACE rev.
