Installation Guide

Preliminary
ZUMMESH-KPBATT
Zūm™ Battery-Powered Wireless Keypad
Installation Guide
SPECIFICATION DETAILS
Power Requirements CR2032 coin cell battery (included);
Provides at least 5 years of battery life
Enclosure 1-gang mountable;
Requires decorator-style faceplate (sold separately)
Environmental
Temperature 30° to 104 °F (0° to 40 °C)
Humidity 10% to 90% RH (noncondensing)
Dimensions
Height 4.25 in (108 mm)
Width 1.77 in (45 mm)
Depth 0.39 in (10 mm)
Description
The Crestron
®
ZUMMESH-KPBATT is an extremely slim battery-powered Zūm™ wireless
keypad with exible installation. The ZUMMESH-KPBATT is a versatile and easy-to-use
addition to the Zūm commercial lighting system. Powered by a battery and slim enough
to mount to the surface of a wall, the keypad’s streamlined design and out-of-the-box
functionality make it ideal for new or retrot installations.
Zūm keypads are preprogrammed. Install a keypad in a room with a Zūm J-Box Zone
Controller (sold separately), perform a series of button taps, and then use the keypad to
control the lights in the room – no programming required! Battery-powered Zūm
keypads are designed in the following four congurations:
• Single-Rocker Switch – Simple on and off lighting control
• Four-Button Keypad – Two buttons for on and off control and two scene recall
buttons
• Six-Button Keypad – Two buttons for on and off control, two buttons for dimming
up and dimming down, and two scene recall buttons
• Six-Button Keypad with Sensor Control - Two buttons for on and off control, two
buttons for dimming up and dimming down, one button for scene recall, and one
button for disabling the sensors in the room
A basic single-room Zūm system consists of Zūm mesh devices, i.e., dimmers, switches,
keypads, and sensors. The Zūm mesh devices in the room communicate directly with
each other without the need for a centralized gateway or processor.
To monitor or control the room from a centralized Crestron control system, use the
ZUMMESH-NETBRIDGE.
NOTE: The ZUMMESH-NETBRIDGE requires a J-box device to provide power.
For quick network setup, use the Zūm app on a smartphone or tablet.
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information. Use a QR reader application on your
mobile device to scan the QR image.
Battery
Prior to operation, remove the battery tab to turn on the keypad.
Installation
NOTES: Observe the following points.
• Codes: Install in accordance with all local and national electrical codes.
• Temperature: For use where temperatures are between 32° to 104 °F (0° to 40 °C).
• Electrical Boxes: Several devices can be installed in one electrical box (multigang).
For a smooth appearance, install one-piece multigang faceplates (not supplied).
Mount the ZUMMESH-KPBATT to a single-gang box or directly to a at surface using
double-sided tape.
Single-Gang Box Mounting
Secure the ZUMMESH-KPBATT to a single-gang box using the two supplied screws.
Attach a decorator-style faceplate (not supplied).
Two screws are supplied
for mounting the keypad to
a back box.
Press rmly to ensure
proper adhesion.
Double-Sided Tape Mounting
Secure the ZUMMESH-KPBATT to a at, clean surface using the supplied double-sided
tape.
1. Clean the mounting surface with a light cleaning agent that does not leave a
residue.
2. Remove the backing of one piece of the double-sided tape and apply it to the back
of the keypad. Repeat for the other piece of double-sided tape.
Two pieces of tape are supplied
to mount the keypad without a
backbox.
3. Ensure that the keypad is vertical, and press it against the wall. Press rmly to
ensure that the keypad is properly secured to the wall.
Remove the battery tab prior
to operation.
Battery Replacement
To remove the battery, insert a pin or paper clip into the slot on the left side of the keypad.
The battery slides out of the opposite side of the keypad.
NOTE: The battery must be inserted properly.
NOTE: The keypad will not operate if the battery is inserted incorrectly.
To install a new battery, insert the battery into the battery slot. The — terminal faces
away from the wall.
To remove the battery,
insert a pin or paper clip
into the hole on the side.
Battery CR2032
(—) towards the front of the keypad
Default Button Functions
Crestron offers several ZUMMESH-KPBATT units.The ZUMMESH-KPBATT’s
functionality is based upon its button layout. By default, they control all loads in the
room. If linked to a dimmer, the ZUMMESH-KPBATT controls only its linked loads.
ON
SCENE 2
SCENE 3
OFF
ON
SCENE 2
SENSOR
DISABLE
OFF
ON
SCENE 2
SCENE 3
OFF
ZUMMESH-KP10ABATT Button Functions
Top Button
Press: Recalls Scene 1
Hold: Raises lights
Bottom Button
Press: Turns lights off
Hold: Lowers lights
ZUMMESH-KP10BBATT Button Functions
On
Press: Recalls Scene 1
Hold: Raises lights
SCENE 2
Press: Recalls Scene 2
Hold 5 Seconds: Saves Scene 2
SCENE 3
Press: Recalls Scene 3
Hold 5 Seconds: Saves Scene 3
OFF
Press: Turns lights off
Hold: Lowers lights
ZUMMESH-KP10CBATT Button Functions
On
Press: Recalls Scene 1
Hold: No action
SCENE 2
Press: Recalls Scene 2
Hold 5 Seconds: Saves Scene 2
SCENE 3
Press: Recalls Scene 3
Hold 5 Seconds: Saves Scene 3
OFF
Press: Turns lights off
Hold: Lowers lights
^
Hold: Raises lights
v
Hold: Lowers lights
ZUMMESH-KP10DBATT Button Functions
On
Press: Recalls Scene 1
Hold: No action
SCENE 2
Press: Recalls Scene 2
Hold 5 Seconds: Saves Scene 2
SENSOR DISABLE
Press: Recalls Scene 3
Hold 5 Seconds: Saves Scene 3
OFF
Press: Turns lights off
Hold: Lowers lights
^
Hold: Raises lights
v
Hold: Lowers lights