Crestron CEN-WAP-ABG-1G 802.
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2008 Crestron Electronics, Inc.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Contents 802.11a/b/g Wireless Access Point: CEN-WAP-ABG-1G 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Specifications .............................................................................................................
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point 802.11a/b/g Wireless Access Point: CEN-WAP-ABG-1G Introduction The CEN-WAP-ABG-1G wireless access point enables wireless communication for Crestron® Wi-Fi touchpanels, 2-Series control systems, computers, and other devices. With IEEE 802.11a/b/g support, easy setup, flush-mount installation, and enterprise level security and management capabilities, the CEN-WAP-ABG-1G delivers an ideal wireless access point solution for any application.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G No Configuration Required Using the CEN-WAP-ABG-1G, a secure Wi-Fi touchpanel connection can be made quickly and easily right out of the box. Each wireless access point ships with a unique network name and network key printed on a removable sticker on the front of the unit. Entering this information into the touchpanel is all that is required to complete the connection.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Specifications Specifications for the CEN-WAP-ABG-1G are listed in the following table. CEN-WAP-ABG-1G Specifications SPECIFICATION DETAILS RF Wireless RF Transceiver IEEE 802.11a/b/g; 5.8 or 2.
02.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Physical Description This section provides information on the connections, controls and indicators available on your CEN-WAP-ABG-1G. CEN-WAP-ABG-1G Physical View (Front and Rear) CEN-WAP-ABG-1G Overall Dimensions (Front View) 2.60 in (6.60 cm) 2.84 in (7.20 cm) 4.14 in (10.51 cm) 1.29 in (3.28 cm) 1.74 in (4.40 cm) 4 • 802.11a/b/g Wireless Access Point: CEN-WAP-ABG-1G Operations & Installation Guide – DOC.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point CEN-WAP-ABG-1G Overall Dimensions (Side View, Left) 0.10 in (0.24 cm) 2.16 in (5.47 cm) 0.61 in (1.55 cm) 0.30 in (0.77 cm) CEN-WAP-ABG-1G Connectors, Controls & Indicators (Front and Rear) 1 2 3 4 NETWORK PoE 5 Operations & Installation Guide – DOC. 6695B 6 802.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Connectors, Controls & Indicators # CONNECTORS, CONTROLS & INDICATORS 1 Antenna 2 LAN 3 Reset (1) Miniature push button that resets the device.* 4 Wi-Fi (1) Green LED: Solid green indicates wireless network connection; Flashing green indicates wireless data activity. 5 AMBER LED NETWORK PoE NETWORK PoE * Reverse SMA, female; Connects to supplied antenna.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Industry Compliance This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc. (E312979) As of the date of manufacture, the CEN-WAP-ABG-1G has been tested and found to comply with specifications for CE marking. FCC ID: MXF-M930907 Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Setup Network Wiring When wiring the Ethernet network, use CAT5 wiring. CAT5 wiring is a twisted pair cable designed for Ethernet networks. These networks operate at speeds of up to 100 Megabits per second (Mbps) using the 100BaseT standard. For information on connecting Ethernet devices in a Crestron system, refer to the latest version of the Crestron e-Control® Reference Guide (Doc.
Crestron CEN-WAP-ABG-1G Wall Mounting 802.11a/b/g Wireless Access Point The CEN-WAP-ABG-1G mounts into a one-gang low-voltage bracket or electrical box. The recommended depth of the electrical box is a minimum of 2.5 inches. The maximum voltage of the access point is 48 VDC. NOTE: To increase airflow, it is recommended that a low-voltage bracket be used instead of an electrical box.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Hardware Hookup Make the necessary connections as called out in the illustration that follows this paragraph. Apply power after all connections have been made. Hardware Connections for the CEN-WAP-ABG-1G (Front View) ANTENNA: FROM 2.4/5.8 GHz ANTENNA (INCLUDED) ETHERNET: 10BaseT/100BaseTX ETHERNET TO LAN (OPTIONAL) NETWORK PoE Hardware Connections for the CEN-WAP-ABG-1G (Rear View) NETWORK PoE: TO 10BaseT/100BaseTX 802.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Configuration Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at http://support.crestron.com. First-time users will need to establish a user account. NOTE: The CEN-WAP-ABG-1G is designed to be functional right out of the box.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Using a Web Browser To access the configuration utility from a Web browser: 1. Start your Web browser. 2. Go to the IP address or host name of the access point. NOTE: If the default Web management port number of 80 has been changed, you must append the port number to the IP address by entering a colon followed by the new port number. If, for example, the IP address is 192.168.10.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Logging In to the Access Point The user name and password window allows you to log in to the access point. “User Name and Password” Window To log in to the access point: 1. Enter the user name and password. The default user name is admin, and the default password is admin. NOTE: The user name and password are not case sensitive. NOTE: For enhanced security, it is recommended that you change the default user name and password.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G To select the configuration mode, do either of the following: • Click Setup Wizard if you wish to configure the access point using the wizard. Refer to “Using Setup Wizard Configuration Mode” below for detailed information. • Click Custom Settings if you wish to customize the settings of the access point. Refer to “Using Custom Settings Configuration Mode” on page 16 for detailed information.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point “Select Configuration” Page (802.11b/g Configuration Profile Shown) To use the wizard: 1. On the “Select Configuration” page, select a configuration profile (802.11b/g, 802.11a, High Security TPMC-8X, or Standalone Network). For detailed information about each of the configuration profiles, read the information provided in the setup wizard for each profile. 2. Click Next.
802.11a/b/g Wireless Access Point 4. Crestron CEN-WAP-ABG-1G Click Next. The “Setup Complete” page opens as shown in the following example. “Setup Complete” Page (802.11b/g Configuration Profile Shown) 5. Review the settings and, if appropriate for your wireless network, click Apply Setting. (If not appropriate, go back to the “Select Configuration” page and select a different configuration profile.) NOTE: When you click Apply Setting, the “Setup Complete” page opens.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Navigating Custom Settings Configuration Mode Custom Settings configuration mode provides four main tabs: BASIC SETUP, WIRELESS, ADMINISTRATION, and STATUS. The BASIC SETUP, WIRELESS, and ADMINISTRATION tabs provide subtabs that allow access to configuration pages. The STATUS tab provides subtabs that allow access to status pages. The following illustration demonstrates the menu tree of Custom Settings configuration mode.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Configuring Basic Setup Settings Basic setup settings allow you to configure the following: Configuring TCP/IP Addressing • TCP/IP addressing • Operational mode • DHCP server settings To configure TCP/IP addressing, click the BASIC SETUP tab and then click the TCP/IP CONFIG subtab. The “TCP/IP Addressing” page opens. “TCP/IP Addressing” Page Refer to the configuration guidelines that follow.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Hostname: (Optional) Enter a name that identifies the access point on the network. The hostname is restricted to the letters a to z (not case sensitive), the digits 1 to 9, and the hyphen. The default setting is CEN-WAP-ABG-1G. Domain name: (Optional) Enter a domain name for the access point. Configuring Operational Mode To configure operational mode, click the BASIC SETUP tab and then click the OPERATIONAL MODE subtab.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G “DHCP Server” Page (DHCP Disabled) Refer to the configuration guidelines that follow. Functionality: From the drop-down list, select either of the following: • Disable: (Default setting) Prevents the access point from functioning as a DHCP server. Select Disable if you do not want a DHCP server or if you already have a DHCP server (such as a router) on your network. • Enable: Allows the access point to function as a DHCP server.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point “DHCP Server” Page – Basic (DHCP Enabled) Default gateway: Enter the IP address of the access point, which is to be used as your network’s gateway. The default gateway address is provided to all client devices that request an IP address from the access point via DHCP. The default setting is 192.168.100.1. Subnet mask: Enter the subnet mask that is set on your network.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Static DHCP Mappings configuration: The following shows the Static DHCP Mappings section of the “DHCP Server” page. “DHCP Server” Page – Static DHCP Mappings The Static DHCP Mappings section allows you to assign static IP addresses to DHCP client devices. As a result, a client device is always assigned the same IP address by the access point.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Static DHCP Mapping Examples Configuring Wireless Settings Wireless settings allow you to configure the following: Configuring Basic Wireless Settings • Basic wireless settings • IEEE 802.11 security settings • MAC filters • Advanced wireless settings • Enterprise (IEEE 802.1x/RADIUS) settings To configure basic wireless settings, click the WIRELESS tab and then click the BASIC subtab. The “Operational Mode” page opens.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Wireless Network Mode: From the drop-down list, select one of the following IEEE wireless standard options: • 11B Only: Specifies 802.11b, which allows a maximum data transfer rate of 11 Mbps and an operating frequency of 2.4 GHz. • 11G Only: Specifies 802.11g, which allows a maximum data transfer rate of 54 Mbps and an operating frequency of 2.4 GHz. • 11 B/G Mixed: (Default setting) Specifies both 802.11b and 802.11g.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Transmit Power: From the drop-down list, select the desired level of transmit power to change the RF coverage: High (default setting), Medium High, Medium, Medium Low, or Low. Setting the transmit power to the highest level maximizes the range, which reduces the number of access points necessary. If you wish to increase the capacity of the network by placing access points closer together, set the transmit power to a lower value to decrease overlap.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Wireless client isolation: From the drop-down list, select either of the following: • Disable: (Default setting) Allows wireless devices connected to the access point to communicate with one another. • Enable: Prevents wireless devices connected to the access point from communicating with one another but allows communication with wired LAN devices.
Crestron CEN-WAP-ABG-1G • 802.11a/b/g Wireless Access Point Enterprise WPA with TKIP or Enterprise WPA with AES NOTE: Enterprise WPA requires a separate RADIUS (Remote Authentication Dial-In User Service) server to manage the log-in process and network keys. For information about configuring RADIUS settings, refer to “Configuring Enterprise (IEEE 802.1x/RADIUS) Settings” on page 31. Enterprise WPA is the recommended security mode for secure corporate use.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Key 1 - Key 4: (Applicable only to Static WEP security mode) For each key, enter hexadecimal characters. Valid hexadecimal characters are 0 to 9, a to f, and A to F (the string of characters is not case sensitive): • If you selected 64 Bits as the Key length, enter 10 hexadecimal characters. • If you selected 128 Bits as the Key length, enter 26 hexadecimal characters.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point NOTE: A low value causes RTS packets to be sent more often, consuming more of the available bandwidth and therefore reducing the apparent throughput of the network packet. The more packets that are sent, however, the quicker the access point can recover from interference or collisions. If several touchpanels are connected to a single access point, lowering the RTS threshold to a value ranging from 500 to 1000 may improve performance.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Functionality: From the drop-down list, select either of the following: • Disable: Prevents MAC address filtering. • Enable: (Default setting) Allows MAC address filtering. The following shows the “MAC Filter” page when MAC filtering is enabled in the Functionality drop-down list. “MAC Filter” Page (MAC Filtering Enabled) If you have enabled MAC filtering, configure MAC filter settings as follows.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Specify MAC addresses of a maximum of 64 wireless devices whose access you want to control by doing either of the following: • Manually enter MAC addresses one at a time: In the MAC Address text box, enter a MAC address in hexadecimal format (xx-xx-xx-xx-xx-xx), and then click Add. The MAC address appears at the bottom of the MAC filter list. Up to 64 MAC addresses can be added to the list – one address at a time.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G “IEEE 802.1x/RADIUS” Page Refer to the configuration guidelines that follow. Primary RADIUS server address: Enter the IP address of the primary RADIUS server. NOTE: The access point can be configured to communicate with two RADIUS servers: a primary server and a secondary server. If the primary RADIUS server fails to respond, the access point can try to communicate with the secondary RADIUS server.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point RADIUS accounting port: Enter the accounting port number of the RADIUS server. The default setting is 1813. NOTE: The RADIUS accounting port is officially assigned to UDP port 1813. RADIUS servers of Microsoft Corporation default to port 1813; however, RADIUS servers of Juniper Networks, Inc. and Cisco Systems, Inc. default to port 1646.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G NOTE: The user name and password are not case sensitive. Old password: Enter the old password. New user name: Enter a new user name. New password: Enter a new password. Re-enter to confirm: Reenter the new password for confirmation of the password.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Please select a file to restore: In the text box, enter the path to the filename containing previous configuration settings by clicking Browse and selecting the configuration file from your computer’s hard drive. Click Restore to start the configuration restore process. The access point reboots automatically when the configuration restore process is complete.
802.11a/b/g Wireless Access Point Configuring External Control Settings Crestron CEN-WAP-ABG-1G External control settings consist of the following: • Basic security settings that include enabling/disabling the front Ethernet port and assigning a new Web management port number. • UPnP (Universal Plug and Play) Ethernet protocol settings that allow autodiscovery of devices on the local network.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point From the drop-down list, select either of the following: • Disable: Prevents the access point from transmitting UPnP broadcast messages and therefore increases device security on an insecure network. NOTE: Disabling UPnP prevents the Device Discovery Tool of the Crestron Toolbox from finding the access point on the network. As a result, the configuration utility of the access point can only be accessed from a Web browser.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Read-write community: In the text box, enter a text string that functions as a password to allow the SNMP manager to read configuration settings from and write configuration settings to the access point. The default setting is private. The readwrite community text string appears as solid black circles.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Model: Displays the model number of the access point: CEN-WAP-ABG-1G. BIOS/Firmware version: Displays the BIOS (Basic Input/Output System) and firmware versions. Operational Mode: Displays the basic operational mode: WiFi Access Point or WiFi Bridge. MAC address: Displays the MAC address of the access point. System up time (hr:min:sec): Displays the amount of time in hours, minutes, and seconds that the access point has been powered on.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Security mode: Displays the security mode of the access point: Static WEP, Enterprise WEP, WPA-PSK with TKIP, WPA-PSK with AES, WPA2-PSK with TKIP, WPA2-PSK with AES, Enterprise WPA with AES, Enterprise WPA with TKIP, Enterprise WPA2 with AES, or Enterprise WPA2 with TKIP. If security mode is disabled, the setting is displayed as Open System. SSID broadcasts: Displays whether SSID broadcasting is enabled or disabled.
Crestron CEN-WAP-ABG-1G Viewing the System Log 802.11a/b/g Wireless Access Point For troubleshooting purposes, you can view a log of system events that include the following: • General system events, which consist of system and network connectivity status changes. • Built-in access point system events, which consist of wireless client association and authentication status changes. • MIB II traps, which display Cold Start, Warm Start, Link Up, Link Down, and SNMP Authentication Failure trap messages.
802.11a/b/g Wireless Access Point Viewing the Status of Associated Wireless Clients Crestron CEN-WAP-ABG-1G To view the status of wireless clients that are associated with the access point, click the STATUS tab and then click the WIFI CLIENTS subtab. The “Associated Wireless Clients” page opens. “Associated Wireless Clients” Page NOTE: To refresh the screen, click Refresh at the bottom of the screen. For each associated client, the Wireless Clients Status table displays the following information: No.
Crestron CEN-WAP-ABG-1G Viewing DHCP Mappings 802.11a/b/g Wireless Access Point You can view the status of current static and dynamic DHCP mappings. Static DHCP mappings are set in the Static DHCP Mappings section of the “DHCP Server” configuration page. Dynamic DHCP mappings are based on the Starting IP address and Maximum number of DHCP users settings of the “DHCP Server” page. For additional information about DHCP server configuration, refer to “Configuring DHCP Server Settings” on page 19.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. CEN-WAP-ABG-1G Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION LAN LED does not illuminate. Network cable is not connected to the NETWORK PoE port on the rear of the access point or to the 10BaseT/100BaseTX compatible device.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point CEN-WAP-ABG-1G Troubleshooting (Continued) TROUBLE POSSIBLE CAUSE(S) Green LED on front Ethernet port does not illuminate. Low signal strength CORRECTIVE ACTION Network cable is not connected to the front Ethernet port or to the 10BaseT/100BaseTX compatible device. Verify network cable connection to the front Ethernet port and to the network device. Network cable is not the proper type.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G CEN-WAP-ABG-1G Troubleshooting (Continued) TROUBLE Wireless network device cannot connect to the access point and cannot see the SSID. POSSIBLE CAUSE(S) Errors exist with the configuration of the access point. CORRECTIVE ACTION Check that the operational mode is set to WiFi Access Point. For additional information, refer to “Configuring Operational Mode” on page 19. Check that the radio mode (802.11a/b/g) is compatible with the network device.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling Crestron at 1-888-CRESTRON [1-888-273-7876]. You can also log onto the online help section of the Crestron website (www.crestron.com/onlinehelp) to ask questions about Crestron products.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Software License Agreement This License Agreement (“Agreement”) is a legal contract between you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for software referenced in this guide, which includes computer software and as applicable, associated media, printed materials and “online” or electronic documentation (the “Software”).
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity with Your valid licenses from Crestron of its authorized agent.
802.11a/b/g Wireless Access Point Crestron CEN-WAP-ABG-1G Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron CEN-WAP-ABG-1G 802.11a/b/g Wireless Access Point This page is intentionally left blank. This page is intentionally left blank. Operations & Installation Guide – DOC. 6695B 802.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 6695B (2022090) 10.08 Specifications subject to change without notice.
